Freestyle Predator Watch Manual

Buttons

S1. Start/stop Button
S2. Lap/reset Button
S3. Mode Button
S4. Light Button
S5. Lap/reset Button

DISPLAY MODES

The watch has seven display modes: HOME TIME, FOREIGN TIME (T2), ALARM 1 (AL1), ALARM2 (AL2), CHRONOGRAPH (CHR), PACER and TIMER (TMR).
To change from one display mode to another, press S3 button once.

NOTE: In any setting mode, if there is no manipulation for around 2 minutes, the watch will automatically save the entered data and exit the setting procedure.

TO SET THE TIME AND CALENDAR

1. Press S3 button to select HOME TIME mode.
2. Press and hold S2 button for around 3 seconds, the second digits will blink.
3. Press S1 button to reset the second digits to 00. This will increase the time by 1 minute of the original setting is at 30 to 59 seconds.
4. Press S3 button, the minute digits will blink.
5. Press S1 button to set the minute digits. Holding down the button will speed up the process.
6. Press S3 button, the hour digits will blink.
7. Press S1 button to set the hour digits. Holding down the button will speed up the process.
8. Follow the same pattern to set day (of the week), year, month and date.
9. After finished making all the settings, press S2 button to confirm.

NOTE: The year can be set within the range of 2000 to 2099.

TO SET THE FOREIGN TIME

1. Press S3 button to select FOREIGN TIME mode.
2. Press and hold S2 button for around 3 second. The hour digits will blink.
3. Press S1 button to set the hour digits. Holding down the button will speed up the process.
4. After finished making all the settings, press S2 button to confirm.

NOTE: In FOREIGN TIME settings, only hour digits are open to setting. The minutes and seconds counts are synchronized between HOME TIME and FOREIGN TIME mode.

TO SET THE HOUR FORMAT

In HOME TIME mode, press S2 button to toggle between 12-hour and 24-hour format. The A.M. and P.M. indicators will be displayed in 12-hour format.

NOTE: The chosen hour format will apply to both HOME TIME mode and FOREIGN TIME mode.

TO TURN ON/OFF THE HOURLY CHIME

In HOME TIME mode,

1. Press S1 button to activate or deactivate the hourly chime function.
2. When the hourly chime function is activated, the hourly chime indicator will appear.

TO SET THE DAILY ALARMS

1. Press S3 button to select ALARM1 or ALARM2 mode to set.
2. Press and hold S2 button for around 3 seconds, the minute digits will blink.
3. Press S1 button to set the minute digits. Holding down the button will speed up the process.
4. Press S3 button, the hour digits will blink.
5. Press S1 button to set the hour digits. Holding down the button will speed up the process.
6. After finished making all the settings, press S2 button to confirm.

TO TURN ON/OFF THE DAILY ALARMS

In ALARM1 or ALARM2 mode,

1. Press S1 button to activate or deactivate the alarm function.
2. While the alarm function is activated, the alarm indicator will appear.

WHEN AN ALARM GOES OFF

An alarm tune will be emitted at the designated time when the alarm is activated. To stop the tune, press any button.

TO USE THE CHRONOGRAPH

Press S3 button to select CHRONOGRAPH mode.

1. The chronograph will then be displayed in its current state – reset, running, or stopped.
2. To resume a counting, press S1 button to resume from where it left off.
3. To start a new counting, reset the stop watch to zero first.
4. Press S1 button to stop counting, then press S2 button to reset the counter to zero.

For the measurement of elapsed time:
In CHRONOGRAPH mode,

1. Press S1 button to start counting.
   To stop counting, press S1 button.
2. Press S1 button again to resume from where it left off.
3. To reset to zero, press S1 button to stop counting and then press S2 button.

For the measurement of split time:
In CHRONOGRAPH mode,

1. Press S1 button to start counting.
2. While the chronograph is running, press S2/S5 button to register a lap. The chronograph is still running in the background.
   After around 8 seconds, the currently accumulated time will be displayed.
3. Repeat the last step until all the laps have been registered.
4. To stop counting, press S1 button. Press S1 button again to resume from where it left off.
5. To reset to zero, press S1 button to stop counting, then press S2 button to reset the counter to zero.

NOTE: The chronograph can record up to a maximum of 10 laps. If you try to record more than 10 laps, the lap number will show a flashing "F" and the extra laps will not be recorded.

NOTE: You can leave the chronograph running while switching over to other operating modes.

NOTE: The chronograph will count up to 9 hours, 59 minutes and 59.99 seconds before starting from zero again.

TO USE THE RECALL FUNCTION

1. Press S3 button to select RECALL mode.
2. Press S1 button to scroll through the recorded individual lap and split time.

NOTE: The recall function is available only when there is lap record stored.

NOTE: The previous set of lap record will automatically be replaced by the next set of lap record.

TO USE THE PACER

1. Press S3 button to select PACER mode.
2. The pacer frequency will be dis played above the home time.
3. Press S2 button to cycle among the preset values 40, 45, 50, 55, 60, 65, 70, 75, 80, 85, 90, 95, 100, 110, 120, 130, 140, 150 and 160 beeps per minute.
4. After finished making all the settings, press S1 button to start the pacer.
5. To stop the pacer, press S1 button again.

TO SET THE TIMER

1. Press S3 button to select TIMER mode.
2. Press and hold S2 button, the second digits will blink.
3. Press S1 button to set the second digits. Holding down the button will speed up the process.
4. Press S3 button, the minute digits will blink.
5. Press S1 button to set the minute digits. Holding down the button will speed up the process.
6. Press S3 button, the hour digits will blink.
7. Press S1 button to set the hour digits. Holding down the button will speed up the process.
8. After finished making all the settings, press S2 button to confirm.

NOTE: The timer can be set up to a maximum of 9 hours, 59 minutes and 59 seconds.

TO USE THE TIMER

1. Press S3 button to select TIMER mode.
2. The timer will be displayed in its current state – reset, running, or stopped.
3. To resume a counting, press S1 button to resume from where it left off.
4. To start a new counting, reload the timer first. Press S1 button to stop counting and then press S2 button.
5. After reaching zero in a countdown, a tune will be emitted. To stop the tune, press any button.

NOTE: You can leave the timer running while switching over to other operating modes.

NOTE: The timer will automatically count up when the timer reaches zero in a countdown.

TO USE THE BACKLIGHT

Press S4 button to turn on the backlight for around 3 seconds.

Documents / Resources

Download manual

Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.

Download Freestyle Predator Watch Manual