FreeStyle Avalon,Aviator, Ballistic Diver - Quartz Analog Watch Manual

TWO-HAND / THREE-HAND MODELS

1. Second Hand

TO SET THE TIME

1. Pull crown out to first click position B.
2. Turn crown to set time.
3. Push crown back to position A.

TWO-HAND / THREE-HAND DATE MODELS

1. Date Indicator

TO SET THE TIME

1. Pull crown out to second click position C.
2. Turn crown to set time.
3. Push crown back to position A.

TO SET THE DATE

1. Pull crown out to first click position B.
2. Turn crown counter-clockwise to set date.
3. Push crown back to position A.

NOTE: Do not set the date between 9:00 P.M. and 1:00 A.M. Otherwise, the date may not change properly on the following day. If it is necessary to set the date during that time period, first change the time to any time outside it, then set the date and then reset to the correct time.

THREE-HAND DAY-DATE MODELS

1. Day (of the week) Indicator
2. Date Indicator

TO SET THE TIME

1. Pull crown out to second click position C.
2. Turn crown to set time.
3. Push crown back to position A.

TO SET THE DAY (OF THE WEEK)

1. Pull crown out to first click position B.
2. Turn crown clockwise to set day.
3. Push crown back to position A.

NOTE: Do not set the day between 9:00 P.M. and 1:00 A.M. Otherwise, the day may not change properly on the following day. If it is necessary to set the day during that time period, first change the time to any time outside it, then set the day and then reset to the correct time.

TO SET THE DATE

1. Pull crown out to first click position B.
2. Turn crown counter-clockwise to set date.
3. Push crown back to position A.

NOTE: Do not set the date between 9:00 P.M. and 1:00 A.M. Otherwise, the date may not change properly on the following day. If it is necessary to set the date during that time period, first change the time to any time outside it, then set the date and then reset to the correct time.

TWO-EYE MULTI-FUNCTION MODELS

6P23

1. Second Hand
2. Day Hand
3. Date Hand

TO SET THE DAY (OF THE WEEK)

1. Pull crown out to second click position C.
2. Turn crown clockwise to set day.
3. Push crown back to position A.

NOTE: The Day Hand will move together with the Hour Hand and Minute Hand. Keep turning the crown until the desired day has been reached.

TO SET THE TIME

1. Pull crown out to second click position C.
2. Turn crown to set time.
3. Push crown back to position A.

TO SET THE DATE

1. Pull crown out to first click position B.
2. Turn crown counter-clockwise to set date.
3. Push crown back to position A.

NOTE: Do not set the date between 9:00 P.M. and 1:00 A.M. Otherwise, the date may not change properly on the following day. If it is necessary to set the date during that time period, first change the time to any time outside it, then set the date and then reset to the correct time.

6P25

1. Second Hand
2. Date Hand
3. 24 Hour Hand

TO SET THE TIME

1. Pull crown out to second click position C.
2. Turn crown to set time.
3. Push crown back to position A.

NOTE: The 24 Hour Hand will also be set during time setting.

TO SET THE DATE

1. Pull crown out to first click position B.
2. Turn crown counter-clockwise to set date.
3. Push crown back to position A.

NOTE: Do not set the date between 9:00 P.M. and 1:00 A.M. Otherwise, the date may not change properly on the following day. If it is necessary to set the date during that time period, first change the time to any time outside it, then set the date and then reset to the correct time.

THREE-EYE MULTI-FUNCTION MODELS

1. Hour Hand
2. Minute Hand
3. Second Hand
4. Date Hand
5. Day Hand
6. 24 Hour Hand

TO SET THE DAY (OF THE WEEK)

1. Pull crown out to second click position C.
2. Turn crown clockwise to set day.
3. Push crown back to position A.

NOTE: The Day Hand will move together with the Hour Hand and Minute Hand. Keep turning the crown until the desired day has been reached.

TO SET THE TIME

1. Pull crown out to second click position C.
2. Turn crown to set time.
3. Push crown back to position A.

NOTE: The 24 Hour Hand will also be set during time setting.

TO SET THE DATE

1. Pull crown out to first click position B.
2. Turn crown either clockwise or counter-clockwise to set date.
3. Push crown back to position A.

NOTE: The direction of crown turning for date setting varies on different watch models.

NOTE: Do not set the date between 9:00 P.M. and 1:00 A.M. Otherwise, the date may not change properly on the following day. If it is necessary to set the date during that time period, first change the time to any time outside it, then set the date and then reset to the correct time.

THREE-EYE CHRONOGRAPH MODELS

OS20

1. Hour Hand
2. Minute Hand
3. Second Hand
4. 24 Hour Hand
5. Chronograph Minute Hand
6. Chronograph Second Hand
7. Date Indicator

S1 – Chronograph start/stop button
S2 – Chronograph reset button

TO ADJUST THE CHRONOGRAPH HANDS POSITION

Before setting the time, check if the Chronograph Second Hand and Chronograph Minute Hand are at the 12 o'clock position.

If the chronograph is in use, press the button in the following order to reset it, and then check if the chronograph hands have returned to 12 o'clock position.

If the chronograph is counting:		S1→S2
If the chronograph is stopped:		S2

In case one or several chronograph hands are not at the zero position due to certain reasons (e.g. following a battery change), that needs to be adjusted.

1. Pull crown out to second click position C.
2. Press S1 button to set the Chronograph Second Hand. Holding down the button will allow quick advance.
3. Push crown back to position A.

TO SET THE TIME

1. Pull crown out to second click position C.
2. Turn crown to set time.
3. Push crown back to position A.

NOTE: The 24 Hour Hand will also be set during time setting.

TO SET THE DATE

1. Pull crown out to first click position B.
2. Turn crown counter-clockwise to set date.
3. Push crown back to position A.

NOTE: Do not set the date between 9:00 P.M. and 1:00 A.M. Otherwise, the date may not change properly on the following day. If it is necessary to set the date during that time period, first change the time to any time outside it, then set the date and then reset to the correct time.

TO USE THE CHRONOGRAPH (STOP-WATCH)

1. Press S1 button to start counting.
2. To stop counting, press S1 button once. Press S1 button again to resume from where it left off.
3. To reset to zero, press S1 button to stop counting and then press S2 button.

VD53

1. Hour Hand
2. Minute Hand
3. Second Hand
4. 24 Hour Hand
5. Chronograph Minute Hand
6. Chronograph Second Hand
7. Calendar

S1 – Chronograph start/stop button
S2 – Chronograph split/split release/reset button

TO ADJUST THE CHRONOGRAPH HANDS POSITION

Before setting the time, check if the Chronograph Second Hand and Chronograph Minute Hand are at the 12 o'clock position.

If the chronograph is in use, press the button in the following order to reset it, and then check if the chronograph hands have returned to 12 o'clock position.

If the chronograph is counting:	S1→S2
If the chronograph is stopped:	S2
If the split time is displayed:	S2→S1→S2

In case one or several chronograph hands are not at the 12 o'clock position due to certain reasons (e.g. following a battery change), that needs to be adjusted.

1. Pull crown out to second click position C.
2. Press S1 or S2 button to set the Chronograph Second Hand and Chronograph Minute Hand (mechanically coupled). By pressing S1 or S2 button, the hands will move counterclockwise or clockwise respectively.
3. Push crown back to position A.

TO SET THE TIME

1. Pull crown out to second click position C.
2. Turn crown to set time.
3. Push crown back to position A.

NOTE: The 24 Hour Hand will also be set during time setting.

TO SET THE DATE

1. Pull crown out to first click position B.
2. Turn crown clockwise to set date.
3. Push crown back to position A.

NOTE: Do not set the date between 9:00 P.M. and 1:00 A.M. Otherwise, the date may not change properly on the following day. If it is necessary to set the date during that time period, first change the time to any time outside it, then set the date and then reset to the correct time.

TO USE THE CHRONOGRAPH (STOP-WATCH)

For the measurement of elapsed time,

1. Press S1 button to start counting.
2. To stop counting, press S1 button once. Press S1 button again to resume from where it left off.
3. To reset to zero, press S1 button to stop counting and then press S2 button.

For the measurement of split time,

1. Press S1 button to start counting.
2. While the chronograph is running, press S2 button once to register a lap. The chronograph is still running in the background.
   To display the currently accumulated time, press S2 button again. The chronograph hands will quickly advance to the ongoing measured time.
3. Repeat the last step until all the laps have been registered.
4. To reset to zero, press S1 button to stop counting and then press S2 button.

NOTE: The chronograph is able to measure up to 60 minutes.

JS50

1. Hour Hand
2. Minute Hand
3. Second Hand
4. 24 hour Hand
5. Chronograph Second Hand
6. Chronograph Minute Hand

S1 – Chronograph start/stop button
S2 – Chronograph reset button

TO ADJUST THE CHRONOGRAPH HANDS POSITION

Before setting the time, check if the Chronograph Second Hand and Chronograph Minute Hand are at the zero position.

If the chronograph is in use, press the button in the following order to reset it, and then check if the chronograph hands have returned to zero position.

If the chronograph is counting:		S1→S2
If the chronograph is stopped:		S2

In case one or several chronograph hands are not at the zero position due to certain reasons (e.g. following a battery change), that needs to be adjusted.

1. Pull crown out to first click position B.
2. Press S1 button to set the Chronograph Second Hand and Chronograph Minute Hand (mechanically coupled). Holding down the button will allow quick advance.
3. Push crown back to position A.

TO SET THE TIME

1. Pull crown out to first click position B.
2. Turn crown to set time.
3. Push crown back to position A.

NOTE: The 24 Hour Hand will also be set during time setting.

TO USE THE CHRONOGRAPH (STOP-WATCH)

For the measurement of elapsed time.

1. Press S1 button to start counting.
2. To stop counting, press S1 button once. Press S1 button again to resume from where it left off.
3. To reset to zero, press S1 button to stop counting and then press S2 button.

NOTE: The chronograph is able to measure and display time in 1 second unit up to maximum of 29 minutes 59 seconds. The chronograph will stop automatically after running continuously for 30 minutes.

TO USE THE BACKLIGHT

Some watch models are equipped with an electroluminescence (EL) backlight. To turn on the backlight, press the backlight button.

If there is no separate backlight button, press the crown to activate the backlight.

SCREW-DOWN CROWN

Some watch models are equipped with a screw-down crown. Make sure to unscrew the crown before pulling out the crown for setting, then screw the crown back in tightly after setting to avoid any water entry.

TO USE THE COMPASS

The red pointer of the compass represents the direction of magnetic North (N).

With reference to the red pointer, you can then locate the directions of East, South and West.

DISCLAIMER - The compass should not be relied upon to determine precise location, proximity, distance or direction. In addition, some areas have more magnetic interference than others. This interference may result in further distortion of the compass reading. This compass is designed to point to magnetic north, not true north. Please take into consideration the level of declination based on your global position.

To reduce carbon foot print, these Freestyle instructions are printed with soy inks on recycled paper.