Marantz av surround receiver user guide (15 pages)
Summary of Contents for Marantz SR5010/U1B
Page 1
Service SR5010 / U1B/N1B/N1SG /K1B Manual AV SURROUND RECEIVER • For purposes of improvement, specifications and design are subject to change without notice. • Please use this service manual with referring to the operating instructions without fail. • Some illustrations using in this service manual are slightly different from the actual set. Ver.
Contents ABOUT THIS MANUAL ..............3 CLOCK FLOW & WAVE FORM IN DIGITAL BLOCK .....90 What you can do with this manual ...........3 LEVEL DIAGRAM ...............91 Using Adobe Reader (Windows version) ........4 BLOCK DIAGRAM ..............97 SAFETY PRECAUTIONS ...............6 POWER DIAGRAM ..............100 NOTE FOR SCHEMATIC DIAGRAM ..........7 WIRING DIAGRAM ..............101 NOTE FOR PARTS LIST ..............7...
ABOUT THIS MANUAL Read the following information before using the service manual. What you can do with this manual Search for a Ref. No. (phrase) Jump to the target of a schematic diagram connector (Ctrl+Shift+F) You can use the search function in Acrobat Reader to search for a Ref.
SAFETY PRECAUTIONS The following items should be checked for continued protection of the customer and the service technician. leakage current check Beforereturningthesettothecustomer,besuretocarryouteither(1)aleakagecurrentcheckor(2)alinetochassis resistance check. If the leakage current exceeds 0.5 milliamps, or if the resistance from chassis to either side of the power cord is less than 460 kohms, the set is defective.
NOTE FOR SCHEMATIC DIAGRAM WARNING: Partsindicatedbythe z markhavecriticalcharacteristics.UseONLYreplacementpartsrecommendedbythemanufacturer. CAUTION: Beforereturningthesettothecustomer,besuretocarryouteither(1)aleakagecurrentcheckor(2)alinetochassisresistancecheck. If the leakage current exceeds 0.5 milliamps, or if the resistance from chassis to either side of the power cord is less than 460 kohms, the set is defective. WARNING: DONOTreturnthesettothecustomerunlesstheproblemisidentifiedandremedied.
TECHNICAL SPECIFICATIONS n Audio section n Wireless LAN section • Power amplifier Network type (wireless LAN standard) : Conforming to IEEE 802.11b Conforming to IEEE 802.11g Rated output : Conforming to IEEE 802.11n Front : (Wi-Fi® compliant)z1 100 W + 100 W ( 8 Ω, 20 Hz - 20 kHz with 0.08 % T.H.D.) Security : WEP 64 bit, WEP 128 bit 140 W + 140 W ( 6 Ω, 1 kHz with 0.7 % T.H.D.)
CAUTION IN SERVICING Initializing This Unit Make sure to initialize this unit after replacing the microcomputer or any peripheral equipment, or the digital PCB. Press the power button to turn off the power. While holding down buttons "TUNER PRESET CH -" and "TUNER PRESET CH +" simultaneously, press the power button to turn on the power.
DISASSEMBLY • Remove each part following the flow below. • Reassemble the removed parts in the reverse order. Read "Precautions During Work"before reassembling the removed parts. • • If wire bundles are removed or moved during adjustment or part replacement, reshape the wires after completing the work.
Page 13
Explanatory Photos for DISASSEMBLY • For the shooting direction of each photos used in this manual, see the photo below. • A, B, C and D in the photo below indicate the shooting directions of photos. • The photographs with no shooting direction indicated were taken from the top of the unit. •...
1. FRONT PANEL ASSY Proceeding : TOP COVER FRONT PANEL ASSY → (1) Remove the screws. View from the bottom (2) Remove the screws. Remove the CORD HOLDERs and the connector wires. Remove the FFC. CP4400 CORD HOLDER N1008 2. RADIATOR ASSY Proceeding : TOP COVER FRONT PANEL ASSY RADIATOR ASSY...
3. HDMI PCB Proceeding : TOP COVER BACK CHASSIS HDMI PCB → → (1) Remove the screws. Shooting direction: A (2) Cut the wire clamps, and then remove the CORD HOLDERs and the connector wires. Remove the FFC. CORD HOLDER x 5 N1033 N1008 (3) Cut the wire clamp and remove the connector.
4. VIDEO PCB Proceeding : TOP COVER BACK CHASSIS HDMI PCB VIDEO PCB → → → (1) Remove the connector. CN5000 CN5000 5. PREOUT PCB Proceeding : TOP COVER → BACK CHASSIS → HDMI PCB → VIDEO PCB → PREOUT PCB (1) Remove the connectors.
6. MAIN PCB Proceeding : TOP COVER BACK CHASSIS HDMI PCB VIDEO PCB PREOUT PCB MAIN PCB → → → → → (1) Remove the screws. View from the bottom (2) Remove the screws. CP402 from CP403 from CP405 CP401 CP5003 7.
SPECIAL MODE Special mode setting button No. 1 - 6, 9 : While holding down buttons "A", "B" and "C" simultaneously, press the power button to turn on the power. No. 7, 8 : While the power is on, hold down buttons "A" and "B" for at least 3 seconds . No.
1. Version Display Mode 1.1. Actions Version information is displayed when the device is started in this mode. 1.2. Starting up While holding down buttons "DIMMER" and "STATUS" simultaneously, press the power button to turn on the power. then press the "STATUS" button to display the information in section 1.3 on the display. The version list is also displayed on GUI while the version is displayed on the display.
Page 20
1.4. Error display See the table below for descriptions of the displayed errors and countermeasures for these. If multiple errors occur, only one item is displayed. The priority order is w , e , r , t , y , q . Condition States Display...
Page 21
1.5. Version Display in the Setup Menu Follow the steps below to display the firmware information. (1) Press the "SETUP" button on the remote control. (2) Select "General - Information - Firmware". The version information is displayed as a 12-digit number as shown in the screenshot below. General/Firmware XXXX-XXXX-XXXX Version...
2. PANEL / REMOTE LOCK Selection Mode 2.1. Actions Switch the PANEL LOCK and REMOTE LOCK modes between on and off. 2.2. Starting up While holding down buttons "M-DAX" and "DIMMER" simultaneously, press the power button to turn on the power. Select the desired mode using the "TUNER PRESET CH+"...
3. Selecting the Mode for Service-related Operations 3.1. Actions Select diagnostic mode (service path check mode), protection history display mode, or 232C standby clear mode. 3.2. Starting up While holding down buttons "ZONE2 SOUCE" and "STATUS" simultaneously, press the power button to turn on the power.
Page 24
3.4. DIAGNOSTIC MODE (Service Path Check Mode) 3.4.1. Actions This function is convenient for confirming problem paths in the product and checking the paths after repairing. The Video and Audio paths can be checked. The backup data is not rewritten. 3.4.2.
Page 25
3.4.6. Confirmation items for the video system See the block diagram fig.XXth. Paths to be confirmed Display Settings What to confirm Analog Video pass Input Source : CBL/SAT ・ Component input ⇒ Component output Upper V 0 1 V I D E Video Convert (IP Scaler) : OFF, All sources ・...
DIAGNOSTIC PATH DIAGRAM ANALOG AUDIO DIAGRAM fig.01 TO DIGITAL AUDIO BLOCK H/P-L HEADPHONE OUT H/P-R SPK OUT SBL(FL-B/FL-H/BI-AMP/ZONE) SBR(FR-B/FR-H/BI-AMP/ZONE) ANA_FL DSP_FL EXT_FL CBL/SAT ANA_FR ANALOG DSP_FR INPUT EXT_FR GAME DSP_C EXT_C FRONT AUX1 INPUT PREOUT DSP_SW EXT_SW TUNER VOLUME IC ALL MODEL : FM/AM DSP_SL EXT_SL BD34704KS2...
Page 28
ANALOG AUDIO DIAGRAM fig.02b TO DIGITAL AUDIO BLOCK H/P-L HEADPHONE OUT H/P-R SPK OUT SBL(FL-B/FL-H/BI-AMP/ZONE) SBR(FR-B/FR-H/BI-AMP/ZONE) ANA_FL DSP_FL EXT_FL CBL/SAT ANALOG ANA_FR DSP_FR INPUT EXT_FR GAME DSP_C EXT_C FRONT AUX1 INPUT PREOUT DSP_SW EXT_SW TUNER VOLUME IC ALL MODEL : FM/AM DSP_SL EXT_SL BD34704KS2...
Page 30
ANALOG AUDIO DIAGRAM fig.03b TO DIGITAL AUDIO BLOCK H/P-L HEADPHONE OUT H/P-R SPK OUT SBL(FL-B/FL-H/BI-AMP/ZONE) SBR(FR-B/FR-H/BI-AMP/ZONE) ANA_FL DSP_FL EXT_FL CBL/SAT ANALOG ANA_FR DSP_FR INPUT EXT_FR GAME DSP_C EXT_C FRONT AUX1 INPUT PREOUT DSP_SW EXT_SW TUNER VOLUME IC ALL MODEL : FM/AM DSP_SL EXT_SL BD34704KS2...
Page 32
ANALOG AUDIO DIAGRAM fig.04b TO DIGITAL AUDIO BLOCK H/P-L HEADPHONE OUT H/P-R SPK OUT SBL(FL-B/FL-H/BI-AMP/ZONE) SBR(FR-B/FR-H/BI-AMP/ZONE) ANA_FL DSP_FL EXT_FL CBL/SAT ANALOG ANA_FR DSP_FR INPUT EXT_FR GAME DSP_C EXT_C FRONT AUX1 INPUT PREOUT DSP_SW EXT_SW TUNER VOLUME IC ALL MODEL : FM/AM DSP_SL EXT_SL BD34704KS2...
Page 34
ANALOG AUDIO DIAGRAM fig.05b TO DIGITAL AUDIO BLOCK H/P-L HEADPHONE OUT H/P-R SPK OUT SBL(FL-B/FL-H/BI-AMP/ZONE) SBR(FR-B/FR-H/BI-AMP/ZONE) ANA_FL DSP_FL EXT_FL CBL/SAT ANALOG ANA_FR DSP_FR INPUT EXT_FR GAME DSP_C EXT_C FRONT AUX1 INPUT PREOUT DSP_SW EXT_SW TUNER VOLUME IC ALL MODEL : FM/AM DSP_SL EXT_SL BD34704KS2...
Page 35
ANALOG AUDIO DIAGRAM fig.06 TO DIGITAL AUDIO BLOCK H/P-L HEADPHONE OUT H/P-R SPK OUT SBL(FL-B/FL-H/BI-AMP/ZONE) SBR(FR-B/FR-H/BI-AMP/ZONE) ANA_FL DSP_FL EXT_FL CBL/SAT ANALOG ANA_FR DSP_FR INPUT EXT_FR GAME DSP_C EXT_C FRONT AUX1 INPUT PREOUT DSP_SW EXT_SW TUNER VOLUME IC ALL MODEL : FM/AM DSP_SL EXT_SL BD34704KS2...
Page 36
VIDEO DIAGRAM fig.07 ADV8195 FRONT HDMI TMDS IN BUFFER OUT0 TMDS OUTPUT HDMI OUT1 TMDS IN HDMI1 HDMI2.0 RX MN864788 HDMI2.0 TX (2.2 4 INPUTS) MN864788 HDMI2 MX25L12835FMI TMDS OUTPUT HDMI IN HDMI OUT2 TMDS OUT TMDS IN HDMI3 OUT1 HDMI4 TMDS OUT HDMI5...
Page 37
VIDEO DIAGRAM fig.08 ADV8195 FRONT HDMI TMDS IN BUFFER OUT0 TMDS OUTPUT HDMI OUT1 TMDS IN HDMI1 HDMI2.0 RX MN864788 HDMI2.0 TX (2.2 4 INPUTS) MN864788 HDMI2 MX25L12835FMI TMDS OUTPUT HDMI IN HDMI OUT2 TMDS OUT TMDS IN HDMI3 OUT1 HDMI4 TMDS OUT HDMI5...
Page 38
VIDEO DIAGRAM fig.09 ADV8195 FRONT HDMI TMDS IN BUFFER OUT0 TMDS OUTPUT HDMI OUT1 TMDS IN HDMI1 HDMI2.0 RX MN864788 HDMI2.0 TX (2.2 4 INPUTS) MN864788 HDMI2 MX25L12835FMI TMDS OUTPUT HDMI IN HDMI OUT2 TMDS OUT TMDS IN HDMI3 OUT1 HDMI4 TMDS OUT HDMI5...
Page 39
VIDEO DIAGRAM fig.10 ADV8195 FRONT HDMI TMDS IN BUFFER OUT0 TMDS OUTPUT HDMI OUT1 TMDS IN HDMI1 HDMI2.0 RX MN864788 HDMI2.0 TX (2.2 4 INPUTS) MN864788 HDMI2 MX25L12835FMI TMDS OUTPUT HDMI IN HDMI OUT2 TMDS OUT TMDS IN HDMI3 OUT1 HDMI4 TMDS OUT uCOM...
Page 41
ANALOG AUDIO DIAGRAM fig.11b TO DIGITAL AUDIO BLOCK H/P-L HEADPHONE OUT H/P-R SPK OUT SBL(FL-B/FL-H/BI-AMP/ZONE) SBR(FR-B/FR-H/BI-AMP/ZONE) ANA_FL DSP_FL EXT_FL CBL/SAT ANALOG ANA_FR DSP_FR INPUT EXT_FR GAME DSP_C EXT_C FRONT AUX1 INPUT PREOUT DSP_SW EXT_SW TUNER VOLUME IC ALL MODEL : FM/AM DSP_SL EXT_SL BD34704KS2...
Page 43
VIDEO DIAGRAM fig.13 ADV8195 FRONT HDMI TMDS IN BUFFER OUT0 TMDS OUTPUT HDMI OUT1 TMDS IN HDMI1 HDMI2.0 RX MN864788 HDMI2.0 TX (2.2 4 INPUTS) MN864788 HDMI2 MX25L12835FMI TMDS OUTPUT HDMI IN HDMI OUT2 TMDS OUT TMDS IN HDMI3 OUT1 HDMI4 TMDS OUT HDMI5...
Page 44
3.5. Protection History Display Mode 3.5.1. Actions This mode enables the unit to record and display the event when the THERMAL, ASO or DC protection is activated. If protections have been activated multiple times, the latest protection operation is recorded. 3.5.2.
Page 45
3.5.4. Clearing the Protection History There are two ways to clear the protection history. (a) Activate Protection History Display Mode. Press the "STATUS" button to display the protection history. Press and hold the "DIMMER" button for 3 seconds. P R O T E C T H I S T O R Y : D C Press and hold the "DIMMER"...
Page 46
3.6. Operation Info Mode 3.6.1. Actions This mode enables the unit to display the accumulated operating time, power on count and each protection count. 3.6.2. Starting up While holding down buttons "ZONE2 SOURCE" and "STATUS" simultaneously, press the power button to turn on the power.
Page 47
3.7. TUNER STEP mode (U / N only) 3.3.1. Actions This is a special mode for enabling reception STEP of the ANALOG TUNER to be changed. 3.7.2. Starting up While holding down buttons "ZONE2 SOURCE" and "STATUS" simultaneously, press the power button to turn on the power.
4. Protection Pass Mode 4.1. Actions • This mode allows the power to be turned on without activating protections. • This mode functions in the same way as normal power-on, except that protections are not activated. 4.2. Operations While holding down buttons "DIMMER", "STATUS" and "SOUND MODE" simultaneously, press the power button to turn on the power.
6. CY920 Initialization Mode 6.1. Actions The following items are initialized. (1) Favorites (2) Quick Select (3) Presets (4) Internet Radio Recently Played (5) Flickr contacts (6) User ID (7) Resume Playback station 6.2. Operations While the power is on, hold down buttons "TUNER PRESET CH -" and "DIMMER" for at least 3 seconds. Initializing Display I n i t i a l W a i t...
JIG FOR SERVICING Use the following jigs (extension cable kit) when repairing the PCBs. Order with your dealer for the jigs your dealer if necessary. CAUTION : Incorrect connections may cause malfunction. • Connection of Jig for HDMI PCB ---Items to Be Prepared--- 8U-110084S EXTENSION UNIT KIT 1Sets...
Page 51
CN5601 TO CP401 CN5602 CN4704 (3) Remove the HDMI PCB from the chassis and turn it over. Place an insulation sheet larger than the PCB underneath the HDMI PCB. Connect the earth of the PCB to the chassis using an earth wire, etc. PCB PREOUT PCB VIDEO Insulation sheet...
PROCEDURE AFTER REPLACING THE MICROPROCESSOR, ETC. The procedure after replacing the u-COM (microprocessor), flash ROM, etc. is as follows. Proce- dure after PCB Name Ref. No. Description Remark Replace- ment R5F564MJCDFC 32BIT SOFTWARE : Main HDMI U1018 HDMI U1025 MX25L6406EM2I-12G 64M SOFTWARE : DSP1 ROM HDMI U1027...
FIRMWARE UPDATE PROCEDURE 1. Updating via USB The latest firmware can be downloaded to a USB memory for updates. 1.1. Connecting to the USB Memory (1) Preparation • Use a memory that supports USB2.0. • USB format : Prepare a USB memory formatted in FAT16 or FAT32. •...
Page 54
1.3. File structure on USB Memory Copy the update files to the USB memory with the following structure. USB memory root Model Name Model Area Product ID SR5010U North America (U) 100100410100 SU5010N Europe (N) 100100410200 SR5010K China (K) 100100410500 + firmwares + X00100XXXXXX + APLD.bin...
Page 55
1.8. The firmware update finishes. When the update is completed, the following message appears on the display, then the unit returns to the normal status. Display U p d a t i n g C o m p l e t e ---Cautions on Firmware Update--- •...
Page 56
1.10. About the error codes See the table below for error codes and details of faults when the firmware is updated through USB memory. Error USB Update Error Display Details of Error code Remedies Code C o n n e c t i o n F a i l Disconnect and reconnect the USB Unable to detect USB.
Page 57
Error USB Update Error Display Details of Error code Remedies Code This unit automatically retries the request several times. Wait until the E r a s e f a i l Error in Verify after rewriting Main Display stops. If the Display stops at the (Check Sum Error).
Page 58
Error USB Update Error Display Details of Error code Remedies Code This unit automatically retries the request several times. Wait until the U p d a t i n g f a i l Error notification received while Display stops. If the Display stops at the requesting the Firmware Info.
Page 59
Error USB Update Error Display Details of Error code Remedies Code This unit automatically retries the request several times. Wait until the U p d a t i n g f a i l Setup failure of the XModem Display stops. If the Display stops at the transfer method.
Page 60
Error USB Update Error Display Details of Error code Remedies Code This unit automatically retries the request several times. Wait until the F i l e s N o t F o u n d No Firmware File in USB. Display stops.
Page 61
1.11. Device display during the firmware update Display the device being updated and the update progress. Target device USB Update Display Error code when an error occurs M a i n 10 - 16 Main CPU 36 - 3D * * * m i n * * % 50 - 52 Audio PLD...
2. Updating via DPMS Download the latest firmware from our website and update the firmware. 2.1. Network Connection (1) System Requirements • Internet Connection by Broadband Circuit • Modem • Router • Ethernet cable (CAT-5 or greater is recommended) (2) Setting Internet Computer Modem...
Page 63
2.3. About the error codes See the following table for details on the error code display, details of the error code, remedies when updating the firm- ware via DPMS. (DPMS : D&M Product Management Server) Error DPMS Update Error Display Details of Error code Remedies Code...
Page 64
Error DPMS Update Error Display Details of Error code Remedies Code Abnormal data in Update Packet U p d a t i n g f a i l Turn off and on the power. Updating received from CY920 (Packet No starts automatically.
Page 65
Error DPMS Update Error Display Details of Error code Remedies Code Check the network connection. Carry C o n n e c t i o n F a i l DPMS connection Time Out Error. out the update in an environment that has little network load.
Page 66
Error DPMS Update Error Display Details of Error code Remedies Code NACK received in response or U p d a t i n g f a i l Turn off and on the power. Updating no response from Sub for the "L" starts automatically.
Page 67
Error DPMS Update Error Display Details of Error code Remedies Code Check the network connection. Carry C o n n e c t i o n F a i l IP Address acquisition failure out the update in an environment that (Time Out).
Page 68
Device display during the firmware update Display the device being updated and the update progress. Target device DPMS Update Display Error code when an error occurs M a i n 10 - 16 Main CPU * * * m i n 36 - 3F * * % 50 - 52...
ADJUSTMENT Adjusting Idling Current 1. Preparation (1) Prepare a DC voltmeter. (2) Place the unit under normal usage conditions, away from highly ventilated areas such as next to an air conditioning machine or electric fan. The set requires an ambient temperature of 15℃ to 30℃ and standard humidity. (3) Settings of This Unit •...
SURROUND MODES AND PARAMETERS Sound modes and channel output S This indicates the audio output channels or surround parameters that can be set. D This indicates the audio output channels. The output channels depend on the settings of “Speaker Config.”. Channel output Front Dolby Surround Dolby...
Page 71
Surround Parameter Audyssey Tone M-DAX Sound mode MultEQ® XT Dynamic EQ Dynamic Volume Center Spread DTS Neural:X Direct/Pure Direct (2-channel) z5 Direct/Pure Direct (Multi-channel) z5 Stereo Multi Ch In Dolby Surround DTS Neural:X Dolby Digital Dolby Digital Plus Dolby TrueHD Dolby Atmos DTS Surround DTS 96/24...
Page 72
Types of input signals, and corresponding sound modes F This indicates the default sound mode. S This indicates the selectable sound mode. c - i Dolby Dolby Dolby Sound mode NOTE Analog / DTS ES DTS ES Dolby Dolby Digital DTS:X DTS-HD Digital...
TROUBLE SHOOTING 1. POWER 1.1. The unit does not power on The unit does not power on Does the power indicator Does the power indicator on on the front panel flash in the front panel flash in red green or white when the when the power is turned on? power is turned on? Is a fuse blown?
2. Analog video CVBS / COMPONENT / HDMI OUT NG Input CVBS Input COMPONENT Input Function : CBL / SAT Function : CBL / SAT HDMI To "3 HDMI/DVI" To "A" <HDMI PCB> test point N1039 N1019 7020-07808-020-0S [MP] N1017 C1295 R1369 C1292...
Page 75
Input CVBS / COMPONENT Check the input signal to the VIDEO DECODER. Can a signal be confirmed at the follow- ing points? HDMI PCB : R2092 Input CVBS : Check B Check the connection between the COMPONENT-Y : R2089 boards. Input COPONENT : Check C COMPONENT-Cb : R2091...
Page 76
Input CVBS Check the settings of each IC. Are the following voltages set? HDMI PCB HDMI PCB faulty. N1039 - 12 pin : Hi (3.3 V) N1039 - 13 pin : Hi (3.3 V) N1039 - 14 pin : Lo (0 V) Extend the HDMI PCB using the jig.
Page 77
Input COMPONENT Check the settings of each IC. Are the following voltages set? HDMI PCB faulty. HDMI PCB N1039 - 11 pin : Lo (0 V) N1039 - 15 pin : Hi (3.3 V) Extend the HDMI PCB using the jig. Is the power voltage being output correctly? Check the connection between the FRONT...
(7) Are the HDMI output settings of the Blu-ray/DVD player correct? and set the HDMI output correctly. (8) When using a Marantz Blu-ray/DVD player, is the "HDMI" indicator of the fluorescent display lit? Proceed to YES when using a Blu-ray/DVD player produced by other manufactures.
Page 79
(11) Are a picture and sound output when a different Blu-ray/DVD The Blu-ray/DVD player is faulty. player is used? Check the TV. Use a TV that supports HDCP. Computer monitors can- (12) Does the TV support HDCP? not be used. If the TV does not support 1080P/4K, a picture cannot be (13) Does the TV support 1080P/4K? output even if the Blu-ray/DVD player is set to 1080P/4K.
4. AUDIO 4.1. AUDIO CHECK No audio output CHECK1 INPUT SURROND MODE SOURCE Check the ANALOG AUDIO BLOCK Audio output OK? ANALOG 2CH DIRECT ANALOG CHECK2 INPUT SURROND MODE SOURCE Check the DIGITAL AUDIO BLOCK Legacy Audio output OK? COAX or OPT (PCM or DolbyDigital or dts…) CHECK3 INPUT...
Page 81
4.2. Power AMP (AMP PCB) No audio output. Protection is activated. Is the power transistor open or short circuited? Replace the power transistor. 2SB1560 / 2SD2390 Is the emitter resistor of the power transistor open? Replace the emitter resistor. 0.47 Ω Is the base resistor of the power transistor open? Replace the base resistor.
Page 82
4.3. Analog audio No audio output. Is a voltage of ± 8 V supplied to Repair the ± 8 V power supply. INPUT PCB CN4006? Is there an audio signal in INPUT PCB Repair the power amplifier. CN401? Connect the connectors correctly. Is the connector correctly connected to the HDMI PCB? Repair the HDMI PCB.
5. Network / Bluetooth / USB 5.1. Cannot connect to the network Check the connection environment Insert the LAN cable correctly and then turn on the pow- Is the LAN cable correctly inserted? er again. Check the connection environment Set the IP address, etc. correctly. When the static IP address is used, check that no other Are the network settings of this unit correct? devices have the same IP address and that the subnet...
Page 84
Can the NET3.3V output voltage (3.3 V) Is E_POWER1 (U1018 uCOM 132 pin) The circuit of E_POWER1 between to Q1071 (FET-SW) be confirmed? "Hi" ? U1018 and Q1071 are faulty. The circuit around Q1071 (FET-SW) is faulty. Can the NET1.2V output voltage (1.2 V) Is E_POWER4 (U1018 uCOM 132 pin) The circuit of E_POWER4 between to U1070 (DC-DC Conv.) be confirmed?
Page 85
5.2. Cannot establish a Bluetooth connection Check the Bluetooth device being used Is the Bluetooth device compatible with the A2DP profile? Use a device that is A2DP profile compatible. Is the Bluetooth function enabled on the Bluetooth device? Enable the Bluetooth function and try connecting again. Checking the unit Is the Wi-Fi/BT antenna cable inserted correctly into CY920? Connect the Wi-Fi/BT antenna cable correctly.
Page 86
5.3. Cannot recognize the connected USB device Check the USB device being used Is a USB hub being used? Do not use a USB hub. This unit supports devices in the FAT16- and FAT32-for- Is the USB device supported by this unit? matted mass storage class, MTP-compatible devices and iPod devices (except for some models).
6. SMPS DC 5V is not output. Replace the IC4140 (TOP268VG) and Is IC4140 (TOP268VG) damaged? D4142 / D4143 /D4144 / D4145. Is the fuse (F4140) functioning proper- Replace the damaged part. Is D4142, D4143, D4144, D4145 or IC4140 damaged? Are there any short circuits caused by Repair the short circuited area on the the soldering on the PCB?
Page 89
Operation waveform for each part Primary drain After primary side rectification (Caution: High voltage, electric shock) (Caution: High voltage, electric shock) C4148 0.01/250v OPTION OPTION D4142 1N4007 ZD4151 D4143 1N4007 ZD4147 ZJ22B ZJ39B After secondary rectifications ZD4152 D4144 1N4007 ZD4148 ZJ22B ZJ39B D4145...
LEVEL DIAGRAM SR5010 LEVEL DIAGRAM FRONT ch BD34704 ANALOG H/POUT + SPEAKER LINE IN GAIN + PCM1690 + PCM9211 + - - MUTE PRE OUT ZONE2 EXT IN (SR5010 ONLY) +30dB SP OUT 4.48Vrms/8Ω MAX SIGNAL LEVEL 0dBFS +20dB +20dB 1.41Vrms PCM1690 DOLBY LIMIT LEVEL (ALLch-3dBFS)
Page 92
SR5010 LEVEL DIAGRAM CENTER ch BD34704 + SPEAKER GAIN PCM1690 (SR5010 ONLY) + + - - MUTE PRE OUT EXT IN (SR5010 ONLY) +30dB SP OUT 4.48Vrms/8Ω 0dBFS MAX SIGNAL LEVEL 1.41Vrms +20dB +20dB DOLBY LIMIT LEVEL (ALLch-3dBFS) 0dBFS +29dB +10dB +10dB -10dBFS...
Page 93
SR5010 LEVEL DIAGRAM SUBWOOFER ch BD34704 MUTE PRE OUT GAIN PCM1690 + + (SR5010 ONLY) - - MUTE PRE OUT EXT IN (SR5010 ONLY) +30dB MAX SIGNAL LEVEL Config1 DOLBY LIMIT LEVEL (ALLch-3dBFS) 0dBFS 0.88Vrms +20dB +20dB 0dBFS +10dB +10dB -10dBFS PREOUT 317mVrms...
Page 94
SR5010 LEVEL DIAGRAM SURROUND ch BD34704 + SPEAKER GAIN PCM1690 (SR5010 ONLY) + + - - MUTE PRE OUT EXT IN (SR5010 ONLY) +30dB SP OUT 4.48Vrms/8Ω 0dBFS MAX SIGNAL LEVEL 1.41Vrms +20dB +20dB DOLBY LIMIT LEVEL (ALLch-3dBFS) 0dBFS +29dB +10dB +10dB -10dBFS...
Page 95
SR5010 LEVEL DIAGRAM SURR.BACK ch BD34704 + SPEAKER GAIN PCM1690 + (SR5010 ONLY) + - - MUTE PRE OUT EXT IN (SR5010 ONLY) +30dB SP OUT NON CLICP MAX SIGNAL LEVEL 4.0Vrms 4.48Vrms/8Ω SP OUT(D/A OUT) 0dBFS DOLBY LIMIT LEVEL 1.41Vrms(ALLch-3dBFS) 1.41Vrms +20dB +20dB...
Page 96
SR5010 LEVEL DIAGRAM ZONE2 BD34704 from F-ch from DA SB-ch SPEAKER + LINE IN + MAIN NET/USB DAC + ZONE2 +30dB SP OUT 0dBFS PCM5100 2.0Vrms MAX SIGNAL LEVEL 2.00Vrms +20dB +20dB 0dBFS -10dBFS +10dB +10dB -20dBFS(DIG.IN) -2.0dB LINE IN 200mV -20dBFS PREOUT...
BLOCK DIAGRAM ANALOG AUDIO DIAGRAM TO DIGITAL AUDIO BLOCK H/P-L HEADPHONE OUT H/P-R SPK OUT SBL(FL-B/FL-H/BI-AMP/ZONE) SBR(FR-B/FR-H/BI-AMP/ZONE) ANA_FL DSP_FL EXT_FL CBL/SAT ANALOG ANA_FR DSP_FR INPUT EXT_FR GAME DSP_C EXT_C FRONT AUX1 INPUT PREOUT DSP_SW EXT_SW TUNER VOLUME IC ALL MODEL : FM/AM DSP_SL EXT_SL BD34704KS2...
CPU LEVEL CHG TO 7B REMOTE3.3V SWM3.3V M3.3V DGND TO 6B SWM3.3V R1366 DGND R1379 R1385 14 13 12 11 10 z OPTION TABLE OTHER AVR1 OTHER AVR2 E3 OTHER AVR2 E2/E1/E1C/K SR5010 U1B/N1B/K R1379 OPEN OPEN R1385 100N-K C1298 100N-K OPEN OPEN...
TO 8C TO C1 MP OPEN N1034 1.0-16-6PB-2 R2099 R2100 DSP1CS DSP1MISO R2079 DSP1MOSI DSP1CLK DGND R2098 DA3.3V OPTION A 19 18 17 MODEL R1866 R1868 OTHER AVR2 OPEN L1129 OTHER AVR1 OPEN CB05YTYH221 Q2202 RT1N141C SR5010 OPEN NR1606 OPEN L1130 CB05YTYH221 R2077...
DIR/A.PLD TO A2 TO A7 TO 2E TO B2 TO D8 TO C2 *FILTER COMPONENTS VALUE TYPE TOLERANCE R1907 METAL FILM OR CARBON 0 ¥Ø ≤ 5% C2065 0.068UF FILM OR CERAMIC (CH OR C0G) ≤ 5% C2067 0.0047UF FILM OR CERAMIC (CH OR C0G) ≤...
CN4701 CP4200 CP4201 CP4205 CP4202 CN4006 CN4703 TO CN5602 TO CP4006 TO CP4007 OPTION D OPTION A TO N1020 PREOUT TO N1016 TO N1014 OTHER AVR2 E3 : 7P N4700 1.0-9-4PW OPTION A TO CP4700 MODEL OTHER AVR1 OTHER AVR2 SR5010 AREA E2/E1C/K...
VIDEO PART VIDEO_F/CNT 1/3 JACK5000 Y/V. CVBS OUT C5033 SR ONLY OPEN CVBS INPUT SW NJM2595MTE1 SR ONLY INPUT OTHER AVR1 OUT PUT SR5010 SW4 SW5 OTHER AVR2 MUTE MUTE VIN 3 CBL/SAT CHASSIS VIN 4 VIN 2 NOT USED V.AUX IC5001 NJM2595MTE1...
VIDEO_F/CNT 2/3 FRONT_CNT PART CP3401 TO N1039 CP3401 CP5000 FUSE F5006,F5007,F5008,F5009 F5005 OTHER AVR1 / OTHER AVR2 OPEN T1.6AL/250V SR5010 CP5000 F5005A F5005B T1.25AL 250V F5005 C5046 TRG_15V_A AVR ONLY (21P) OPEN SR ONLY 25P TO CN5000 CP5003 F5006 T1.6AL 250V F5006B F5006A AC_IN...
TUNER / REG PART TO E6 CP4003 OPTION A CP4002 TO CN4003 OTHER AVR1 / OTHER AVR2 : TO CN4002 4700UF/25V OPTION D SR5010 : 6800UF/25V OPTION C CP4006 OPTION B * MODEL / AREA OPTION MODEL OTHER AVR1 OTHER AVR2 SR5010 AREA E3/E2/E1C/K...
RS_CNT PART (OTHER AVR2 E3 / SR5010 ONLY) CP4700 TO CN4701 OTHER AVR2 E3 : 7P SR_5010 : 11P CP4702 SR5010 ONLY RS232 PART TO CN4702 AUDIO IN PART (AVR SERIES ONLY) PREMUTE_F PRE_SW1 AGND ZONE2_R AGND ZONE2_L MUTE_Z2 AGND CD_R AGND CD_L...
RS232 PART CN4702 RS_CNT PART TO CP4702 SCHEMATIC DIAGRAMS (26/29) GND LINE POWER+ LINE POWER- LINE ANALOG AUDIO DIGITAL AUDIO TMDS SIGNAL ANALOG VIDEO DIGITAL VIDEO HDMI STBY POWER SCH26_FRONT_RS232...
HDMI JACK/TUNER PACK/M3/BRACKET/MX JACK K X23 A X4 F X2 3 X2 20X2 23 X4 2 MARANTZ 22 X4 M X2 SR5010 ALL WARNING: Parts marked with this symbol z have critical characteristics. Use ONLY replacement parts recommended by the manufacturer.
PACKING VIEW Please see the last chapter for the part list. MANUAL POLYBAG ASSY POLYBAG CODE: 6337-04006-201-0S POLYBAG CODE: 6337-21071-900-0S ZIPPER (A4size) Notes on RADIO ( ALL ) SAFETY INST. ( ALL ) JAPAN POST CARD ( F Only) WARRANTY ( U Only ) SPK WIRE LABEL ( ALL ) ZIPPER BAG (A5size) INST.
SEMICONDUCTORS Only major semiconductors are shown, general semiconductors etc. are omitted to list. The semiconductor which described a detailed drawing in a schematic diagram are omitted to list. 1. IC's R5F564MJCDFC (HDMI : U1018) R5F56108VNFP Terminal Functions Pin Name Symbol Function Pu/Pd STBY...
Page 142
Pin Name Symbol Function Pu/Pd STBY STOP STBY UPSEL/P35(IN)/NMI DSP FLAG3 DSP control pin P34/SCK6/SCK0/IRQ4 BDOWN Power failure detection pin P33/TIOCD0/RXD6/ RC IN Remote control signal input pin RXD0/IRQ3-DS NC(NR1606(EU/ P32/TIOCC0/TXD6/TXD0/ JP))/FLASHER FLASHER (RC-5) input pin (NR1606 :U Version Only IRQ2-DS IN(NR1606(NA)/ , SR5010 : All Version)
Page 143
Pin Name Symbol Function Pu/Pd STBY STOP STBY PC1/SCK5/IRQ12 DAC.PLD ERR PLD ERROR detection pin POWER pin PC0/IRQ14 H/P RL HEADPHONE RLY control pin FRONT RL SPEAKER RELAY control pin PB7/TXD9 HSDA HDMI I2C- MN864788 CEC3VPu PB6/RXD9 HSCL HDMI I2C- MN864788 CEC3VPu PB5/SCK9 JTAG TDO...
Page 144
Pin Name Symbol Function Pu/Pd STBY STOP STBY PD4/IRQ4/AN112 Unused DE_RST HDMI ADV7850 RESET control pin PD3/IRQ3/AN111 788_1_HINT HDMI MN864788(TX) HDMI INT input pin 788_1_RST HDMI MN864788(TX) RESET control pin ※ POWER pin PD2/IRQ2/AN110 788_2_HINT HDMI MN864788(RX) HDMI INT input pin 788_2_RST HDMI MN864788(RX) RESET control pin ※...
Page 149
W9864G6KH-5 (HDMI : U1023) W9864G6KH W9864G6KH-5 Pin description 5. PIN DESCRIPTION PIN NUMBER PIN NAME FUNCTION DESCRIPTION Multiplexed pins for row and column address. Row address: A0 A11. Column address: A0 A7. 23 ~ 26, 22, Address A0 A11 A10 is sampled during a precharge command to 29 ~35 determine if all banks are to be precharged or bank selected by BS0, BS1.
Page 150
W9864G6KH-5 Block diagram CLOCK BUFFER CONTROL SIGNAL GENER ATOR COMMAND DECODER COLUMN DECODER COLUMN DECODER CELL ARRAY CELL ARRAY BANK #0 BANK #1 MODE REGIST ER SENSE AMPLIFIER SENSE AMPLIFIER ADDRESS BUFFER DATA CONTROL CIRCUIT BUFFER COLUMN REFRESH COUNTER COUNTER COLUMN DECODER COLUMN DECODER CELL ARRAY...
Page 151
PCM1690 (HDMI : U1048) PCM1690 Pin Function TERMINAL PULL- DESCRIPTION NAME DOWN TOLERANT RSV2 — — — Reserved, tied to analog ground RSV1 — — — Reserved, left open RSV2 — — — Reserved, tied to analog ground RSV1 — —...
Page 152
TERMINAL PULL- DESCRIPTION DOWN TOLERANT NAME VOUT1+ Positive analog output from DAC1 VOUT1- Negative analog output from DAC1 PCM1690 RSV2 — — — Reserved, tied to analog ground AGND2 — — — Analog ground 2 VCC2 — — — Analog power supply 2, +5 V RSV2 —...
Page 153
SLAS764 – MAY 2011 www.ti.com DEVICE INFORMATION TERMINAL FUNCTIONS, PCM510x PCM5100 (HDMI:U1052) PCM510X (top view) Table 2. TERMINAL FUNCTIONS, PCM510x TERMINAL DESCRIPTION NAME CPVDD Charge pump power supply, 3.3V CAPP Charge pump flying capacitor terminal for positive rail CPGND Charge pump ground CAPM Charge pump flying capacitor terminal for negative rail VNEG...
Page 154
ゾーン 3 対応 ゾーン用の 2ch ボリューム搭載 2 線シリアルバスコントロールは、3.3/5V に対応 SQFP-T80C 用途 BD34704KS2 (INPUT : IC4200) AV レシーバ、ホームシアタシステムに最適。 基本アプリケーション回路 Figure 1. 応用回路例 PIN No. SYMBOL PIN No. SYMBOL PIN No. SYMBOL PIN No. SYMBOL SBLIN INR9(SBRIN2) SRIN INL9(SBLIN2) ○製品構造:シリコンモノリシック集積回路...
Page 155
G Internal 75Ω Driver GENERAL DESCRIPTION PACKAGE OUT G Bipolar Technology G Package Outline DIP16,DMP16 The NJM2586A is a wide band 3-input 1-output 3-circuit video amplifier. It is suitable for Y, Pb, and Pr signal because frequency range is 50MHz.The NJM2586A is suitable for AV receiver, STB, I PIN CONFIGURATION and BLOCK DIAGRAM and other high quality AV systems.
Page 158
MAIN MAIN PCB ASS'Y ※Parts indicated by "nsp"on this table cannot be supplied. ※The parts listed below are only for maintenance. Therefore they might differ from the parts used in the unit in appearances or dimensions NOTE:The symbols in the column Remarks indicate the following destinations. U : North America model N : Europe model K : China model F : Japan model B : Black model SG : Silver Gold model...
Page 159
MAIN REF No. Part No. Part Name Remarks Q'ty New Ver C4050,4051 C,FILM POLYESTER RED-0.1UF-K/250V-5RE PCMT365 D02010407H080S C4052 963134501800D C,ELECT GE 85C 10000UF-M/71V,35*50 BULK LAO-71V103MS57P5W1#B D040103089220S C4053 C,ELECT GE 85C 10UF-M/50V,5*11-5RE.SMS SY D040100087070S C4054 963134501800D C,ELECT GE 85C 10000UF-M/71V,35*50 BULK LAO-71V103MS57P5W1#B D040103089220S C4057 963133502380S...
Page 160
FRONT FRONT PCB ASS'Y ※Parts indicated by "nsp"on this table cannot be supplied. ※The parts listed below are only for maintenance. Therefore they might differ from the parts used in the unit in appearances or dimensions NOTE:The symbols in the column Remarks indicate the following destinations. U : North America model N : Europe model K : China model F : Japan model B : Black model SG : Silver Gold model...
Page 162
VIDEO VIDEO PCB ASS'Y ※Parts indicated by "nsp"on this table cannot be supplied. ※The parts listed below are only for maintenance. Therefore they might differ from the parts used in the unit in appearances or dimensions NOTE:The symbols in the column Remarks indicate the following destinations. U : North America model N : Europe model K : China model F : Japan model B : Black model SG : Silver Gold model...
Page 163
INPUT INPUT PCB ASS'Y ※Parts indicated by "nsp"on this table cannot be supplied. ※The parts listed below are only for maintenance. Therefore they might differ from the parts used in the unit in appearances or dimensions NOTE:The symbols in the column Remarks indicate the following destinations. U : North America model N : Europe model K : China model F : Japan model B : Black model SG : Silver Gold model...
Page 164
INPUT REF No. Part No. Part Name Remarks Q'ty New Ver C2148 C,CERAMIC CHIP T.C CH)330PF-J/50V-1608REEL GRM1882C1H331JA01D D010331167165S C2151 C,CERAMIC CHIP T.C CH)1500PF-J/50V-1608REEL GRM1882C1H152JA01D D010152167165S C2152,2153 C,CERAMIC CHIP T.C CH)330PF-J/50V-1608REEL GRM1882C1H331JA01D D010331167165S C2155 C,CERAMIC CHIP T.C CH)240PF-J/50V-1608REEL GRM1882C1H241JA01D D010241167165S C2157 C,CERAMIC CHIP T.C CH)1500PF-J/50V-1608REEL GRM1882C1H152JA01D D010152167165S C2158...
Page 165
SMPS SMPS PCB ASS'Y ※Parts indicated by "nsp"on this table cannot be supplied. ※The parts listed below are only for maintenance. Therefore they might differ from the parts used in the unit in appearances or dimensions NOTE:The symbols in the column Remarks indicate the following destinations. U : North America model N : Europe model K : China model F : Japan model B : Black model SG : Silver Gold model...
Page 166
7CH_AMP 7CH_AMP PCB ASS'Y ※Parts indicated by "nsp"on this table cannot be supplied. ※The parts listed below are only for maintenance. Therefore they might differ from the parts used in the unit in appearances or dimensions NOTE:The symbols in the column Remarks indicate the following destinations. U : North America model N : Europe model K : China model F : Japan model B : Black model SG : Silver Gold model...
Page 167
7CH_AMP REF No. Part No. Part Name Remarks Q'ty New Ver R473 R,CARBON FILM 33K-J,1/5W-52RE-AX C00003336P520S R474,475 00D9630345903 R,FIXED,M.O. RSD-R1-2WJ-0.47 3.5*8.6 P=5MM SMALL R.REEL N113136647820S R476 R,CARBON FILM 2.7K-J,1/5W-52RE-AX C00002726P520S R477 R,CARBON FILM 220K-J,1/5W-52RE-AX C00002246P520S R478 R,METAL FILM 100PPM 3.3K-J,1W-R.REEL C060033265050S R479 R,CARBON FILM 560-J,1/5W-52RE-AX...
Page 168
7CH_AMP REF No. Part No. Part Name Remarks Q'ty New Ver R618 R,CARBON FILM 100K-J,1/5W-52RE-AX C00001046P520S R619 R,METAL FILM 100PPM 270-J,1W-R.RELL C060027165060S R621 R,METAL FILM 100PPM 270-J,1W-R.RELL C060027165060S R623 963252100150S POSISTOR DHPTF1608 471P 115T SMD PTC THERMISTOR F320471001150S R625 R,CARBON FILM 150K-J,1/5W-52RE-AX C00001546P520S R627 R,CARBON FILM 680K-J,1/5W-52RE-AX...
Page 169
7CH_AMP REF No. Part No. Part Name Remarks Q'ty New Ver C461 C,CERAMIC CHIP HIK X7R2200PF-K/50V-2012REEL D011222777200S C463,464 C,ELECT GE 85C 10UF-M/100V,6.3*11-5RE,SMS SY D04010008C050S C466 C,CERAMIC CHIP HIK X7R)0.1UF-K/50V-1608REEL D011104577160S C469 C,CERAMIC CHIP T.C C0G)220PF-J/50V-1608REEL D010221167160S C470 963133502490S C,FILM POLYESTER ST-0.00022UF-J/100V-5RE HPE221J2AP050T DAEHUNG D02022106C250S C471 C,ELECT GE 85C 47UF-M/50V,6.3*11 KR3-050V470ME110-T/A5.0S KOSHIN...
Page 170
HDMI HDMI PCB ASS'Y ※Parts indicated by "nsp"on this table cannot be supplied. ※The parts listed below are only for maintenance. Therefore they might differ from the parts used in the unit in appearances or dimensions NOTE:The symbols in the column Remarks indicate the following destinations. U : North America model N : Europe model K : China model F : Japan model B : Black model SG : Silver Gold model...
Page 171
HDMI REF No. Part No. Part Name Remarks Q'ty New Ver R1044,1045 R,CHIP THICK 0-J,1/16W-1005REEL C20000006M101S R1052 R,CHIP THICK 1.8K-J,1/16W-1005REEL C20001826M101S R1053 R,CHIP THICK 0-J,1/16W-1005REEL C20000006M101S R1055 R,CHIP THICK 1.8K-J,1/16W-1005REEL C20001826M101S R1057,1058 R,CHIP THICK 1.8K-J,1/16W-1005REEL C20001826M101S R1060-1062 R,CHIP THICK 47-J,1/16W-1005REEL C20004706M101S R1063 R,CHIP THICK 1M-J,1/16W-1005REEL...
Page 172
HDMI REF No. Part No. Part Name Remarks Q'ty New Ver R1379 R,CHIP THICK 0-J,1/16W-1005REEL C20000006M101S R1385 R,CHIP THICK 0-J,1/16W-1005REEL C20000006M101S R1393,1394 R,CHIP THICK 4.7K-J,1/16W-1005REEL C20004726M101S R1452 R,CHIP THICK 100-J,1/16W-1005REEL C20001016M101S R1453,1454 R,CHIP THICK 10K-J,1/16W-1005REEL C20001036M111S R1455,1456 R,CHIP THICK 1K-J,1/16W-1005REEL C20001026M101S R1457,1458 R,CHIP THICK 4.7K-J,1/16W-1005REEL...
Page 173
HDMI REF No. Part No. Part Name Remarks Q'ty New Ver R1695-1700 R,NETWORK A-TYPE 47-J 1/16W SMD(1005)*4 WA04X C180470042100S R1701,1702 R,CHIP THICK 47-J,1/16W-1005REEL C20004706M101S R1703-1710 R,NETWORK A-TYPE 47-J 1/16W SMD(1005)*4 WA04X C180470042100S R1711 R,CHIP THICK 47-J,1/16W-1005REEL C20004706M101S R1715,1716 R,CHIP THICK 1K-D,1/16W-1608REEL C20001021M160S R1717,1718 R,CHIP THICK 10K-J,1/16W-1005REEL...
Page 174
HDMI REF No. Part No. Part Name Remarks Q'ty New Ver R1910 R,NETWORK A-TYPE 10K-J*4 1/16W SMD(1005) WA04 C180103042100S R1911 R,CHIP THICK 0-J,1/16W-1005REEL C20000006M101S R1914,1915 R,CHIP THICK 33-J,1/16W-1005REEL C20003306M101S R1916,1917 R,NETWORK A-TYPE 33-J 1/16W SMD(1005)*4 WA04X C180330042100S R1919 R,CHIP THICK 0-J,1/16W-1608REEL C20000006M160S R1920,1921 R,CHIP THICK 33-J,1/16W-1005REEL...
Page 175
HDMI REF No. Part No. Part Name Remarks Q'ty New Ver R2097 R,CHIP THICK 2.2K-J,1/16W-1005REEL C20002226M101S R2098-2100 R,CHIP THICK 100-J,1/16W-1005REEL C20001016M101S R2101-2103 R,CHIP THICK 3.3K-J,1/16W-1005REEL C20003326M101S R2104 R,CHIP THICK 4.7K-J,1/16W-1005REEL C20004726M101S R2105 R,CHIP THICK 3.3K-J,1/16W-1005REEL C20003326M101S R2108 R,CHIP THICK 3.3K-J,1/16W-1005REEL C20003326M101S R2109 R,CHIP THICK 10K-J,1/16W-1005REEL...
Page 176
HDMI REF No. Part No. Part Name Remarks Q'ty New Ver C1359-1368 C,CERAMIC CHIP HIK X7R)0.1UF-K/16V-1005REEL D011104177101S C1370-1372 C,CERAMIC CHIP HIK X7R)0.1UF-K/16V-1005REEL D011104177101S C1380S C,CERAMIC CHIP HIK X5R)10UF-K/16V-2012REEL GRM21BR61C106KE15L D011106573200S C1385S-1387 C,CERAMIC CHIP HIK X7R)0.1UF-K/16V-1005REEL D011104177101S C1388S C,CERAMIC CHIP HIK X7R)0.01UF-K/25V-1005REEL D011103174101S C1389S,1390 C,CERAMIC CHIP HIK X7R)0.1UF-K/16V-1005REEL...
Page 180
HDAM HDAM PCB ASS'Y ※Parts indicated by "nsp"on this table cannot be supplied. ※The parts listed below are only for maintenance. Therefore they might differ from the parts used in the unit in appearances or dimensions NOTE:The symbols in the column Remarks indicate the following destinations. U : North America model N : Europe model K : China model F : Japan model B : Black model SG : Silver Gold model...
Page 181
HDAM REF No. Part No. Part Name Remarks Q'ty New Ver R4281 R,CHIP THICK 1M-J,1/16W-1608REEL C20001056M160S R4282 R,CHIP THICK 22-J,1/16W-1608REEL C20002206M160S R4283 R,CHIP THICK 1M-J,1/16W-1608REEL C20001056M160S R4284 R,CHIP THICK 22-J,1/16W-1608REEL C20002206M160S R4285,4286 R,CHIP THICK 33K-J,1/16W-1608REEL C20003336M160S R4287,4288 R,CHIP THICK 150-J,1/16W-1608REEL C20001516M160S R4289 R,CHIP THICK 5.6K-J,1/16W-1608REEL...
Page 182
PREOUT PREOUT PCB ASS'Y ※Parts indicated by "nsp"on this table cannot be supplied. ※The parts listed below are only for maintenance. Therefore they might differ from the parts used in the unit in appearances or dimensions. NOTE:The symbols in the column Remarks indicate the following destinations. U : North America model N : Europe model K : China model F : Japan model B : Black model SG : Silver Gold model...