Page 1
PACIFIC RANGE HOOD OPERATING INSTRUCTION Model Number: SC9830AS, SC9836AS Read all instructions before operating the range hood. Airflow Control Technology www.pacifichoods.com www.2pacific.com 331-01-000467(2)
Safety Information READ AND SAVE THESE INSTRUCTIONS Your safety and the safety of others are very important. WARNING We have provided many important safety messages in this manual for your appliance. Always read and obey all safety messages. WARNING - TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING: a) Use this unit only in the manner intended by the manufacturer.
Page 4
Safety Information READ AND SAVE THESE INSTRUCTIONS WARNING WARNING WARNING - TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, WARNING - TO REDUCE THE RISK OF INJURY TO PERSONS OR INJURY TO PERSONS, OBSERVE THE FOLLOWING: IN THE EVENT OF A RANGE TOP GREASE FIRE, OBSERVE THE Installation work and electrical wiring must be done by qualified person(s) in accordance with all applicable codes and SMOTHER FLAMES with a close-fitting lid, cookie sheet, or...
Page 5
Safety Information READ AND SAVE THESE INSTRUCTIONS Operation Always leave safety grilles and filters in place. Without these components, operating blowers could catch onto hair, fingers and loose clothing. The manufacturer declines all responsibility in the event of failure to observe the instructions given here for installation, maintenance and suitable use of the product.
5. 3-min and 5-min automatic delay off 6. Built-in timer 7. Built-in air quality detector (AQI) 8. Airflow Control Technology (ACT™) 9. Compatible with Pacific Kitchen + App 10. Compatible with Google Home and Amazon Alexa Performance Specification Chart Model...
List of Materials Supplied STANDARD CONFIGURATION HARDWARE PACKAGE CONTENTS P3 Wire nuts Hood #6 x 1" Wood screws #6 x 1-1/2" Wood screws 7”Collar #6 x 2 " Wood screws 5 x 24 x 1T washers 3/16 x 10 " screws Oil cup Holder, Deflector Board 太...
Installation Guidelines 1.Location • Air turbulence from window/door may reduce the effectiveness of hood. Suggest to close window/door before using the hood .(FIG. 1) 2.Mounting Height and Position • The installation height is measured vertically from the center of the (FIG.1) hood to the top of the cooktop.
Page 12
Installation Instructions – Under Cabinet 1.Open package to confirm contents and check product appearance. 2.Refer the mounting height on Page 9. 3.Locate the wooden beam and mark the location. (see Fig. 1) (Fig. 1) 4. Place the template at the desired location on the wall, and drill the holes as indicated on the template, remove the template after all holes were drilled.
Page 13
Installation Instructions – Under Cabinet 6.Attach the mounting bracket to the wall using (6) #6 x 2”screws.(see Fig. 4) (Fig. 4) 7.Remove the bottom panel from the hood by using a Phillips head screwdriver to remove each screw. Use caution when removing the bottom panel. Be careful not to scratch side panels during removal.
Page 14
Installation Instructions – Under Cabinet 9.Lift the hood and insert mounting bracket into (2) lower holes on the hood's back panel. (see Fig. 7) (Fig. 7) Push the hood against the bottom of cabinet and secure the hood using (4) #6 screw to the drilled screw holes. (see Fig. 8) (Fig.
Page 15
Installation Instructions – Under Cabinet 12.Reinstall bottom panel. Use caution when installing bottom panel. Be careful not to scratch side panels during installation.(see Fig. 9) (Fig. 9) 13.Install the deflector board and oil cup. Press the left and right side clip to engage the deflector board with clip holder.(see Fig. 10) (Fig.
Page 16
Installation Instructions – Wall 1.Open package to confirm contents and check product appearance. 2.Refer the mounting height on Page 9. 3. Locate the wooden beam and mark the location. (see Fig. 1) (Fig. 1) 4.Place the mounting bracket to the desired location and secure the bracket using (6) #6x2 screws.
Page 17
Installation Instructions – Wall 5.Attach the round rubbers on the lower back panel of the hood. (see Fig. 3) Round Rubber (Fig. 3) Round Rubber 6.Remove bottom panel from hood using a Philips head screwdriver to remove each of the screws. Use caution when removing the bottom panel.
Page 18
Installation Instructions – Wall 7.Install collar and duct work, then seal with aluminum duct tape. (see Fig. 5) (Fig. 5) 8.Lift the hood and insert mounting bracket into (2) upper holes on the hood's back panel. (see Fig. 6) (Fig. 6) Then fasten (2) 6# x 2”screws into wall on the back panel of the hood.
Page 19
Installation Instructions – Wall 11.Reinstall bottom panel. Use caution when installing bottom panel. Be careful not to scratch side panels during installation. (see Fig. 8) (Fig. 8) 12.Install the deflector board and oil cup. Press the left and right side clip to engage the deflector board with clip holder.(see Fig. 9) (Fig.
Installation Instructions – Optional Duct Cover P1C-0098 Duct cover Optional Duct Cover : 30-9/16"- 57-3/16" Model #: P1C-0098 Note: P1C-0098 is not supplied in the package, To order it, please visit us online at www.2pacific.com or call 888-833-8833. Installation 1. Attach the bottom bracket on the top of hood using (2) M4x8 screws to secure on each side.
Page 21
Installation Instructions – Optional Duct Cover 2. set the front of the lower duct cover against the front of the hood using (2) M4x8 screw to secure from inside of the hood. Then secure the side of the lower duct cover to the bottom bracket by using (2) M4x8 screws. 3.
Page 22
Installation Instructions – Optional Duct Cover SC0930/SC0936 Duct cover Optional Duct Cover :12" Model #: SC0930 (30”) / SC0936 (36”) Note: SC0930/SC0936 is not supplied in the package, To order it, please visit us online at www.2pacific.com or call 888-833-8833. pacifichoods.com 718-633-3688 12”...
Page 23
Installation Instructions – Optional Duct Cover 2. Place assembled duct cover on top of hood. Make sure the screw holes of the center panel are facing down and match up with the holes on top of hood. 3. Attach the duct cover to the top of hood by securing the rest of the screws to it from the inside of the hood.
Operating Instructions Timer A Q I PROXIMITY SENSOR Approaching the hood while the power is off, the clock will illuminate. If neither the fan nor lights are turned on within 60 seconds, the clock will turn off. The icons will not disappear until the fan and lights are turned off. 1.
Page 25
Operating Instructions Timer A Q I Delay off While the fan is on, press the Delay off button to enable the delay off timer, it provides the options for either 3 or 5 minutes, press one time for 5 minutes, press again for 3 minutes, the delay off timer will automatically operate after 3 seconds when the timer is selected.
Page 26
Operating Instructions Timer A Q I 7. AQI While the fan is off, press the AQI button to start detecting the air quality near the hood, the icon will illuminate. After completed the detective, the icon will indicate the air quality level in three different colors. (1) Green -The air quality is good, will keep the fan off.
Page 27
Download the app. Pacific Kitchen + NOTE: The Pacific Kitchen+ app is available on iOS devices using iOS 11.0 or later or Android devices using Android version 8 or later. 3. Binding To add your hood , please scan the QR code located on the cover of your manual or inside the hood (typically located behind the oil cup).
Page 28
“Add devices” go to “Set up” screen. the “Add and manage”screen. screen. (5) Login with Pacific Kitchen + (6) Close the window to continue. (4) Find “Pacific Kitchen +” App account. in search bar and click “Pacific Kitchen +”...
Features & Controls Control Type Amazon Alexa Voice Commands Description Alexa, Turn on [Hood Name] Turn on range hood power Power Alexa, Turn off [Hood Name] Turn off range hood power Alexa, Increase [Hood Name] Fan Speed Increase fan speed on range hood Alexa, Decrease [Hood Name] Fan Speed Decrease fan speed on range hood Alexa, Set [Hood Name] Fan Speed to [1-6]...
Page 30
Some local codes limit the maximum amount of CFM a range hood can move. ACT™ allows you to control the maximum blower CFM of select Pacific range hoods without the need for expensive make up air kits. ACT™ enables the installer to easily set the maximum blower speed to one of three most commonly specified CFM levels;...
Surface Maintenance Surface Maintenance 1. Please clean the range hood surface regularly with warm soapy water and wipe with a cotton cloth to prevent grease from accumulating. 2. Please do not use harsh cleansers or coarse material to clean the surface because that will damage the surface.
Steam Clean Function Remarks Functions 1. The range hood should be cleaned by using distilled water or decalcified water only. The cleaning process works by centrifuga force and cleaning power generated by revolving motors at high speed, It will keep the inside of the blower housing clean and prolong the lifespan of the range hood.
Troubleshooting Make sure the circuit breaker and the unit’s After installation, the The power source is not turned ON. unit doesn’t work. power is ON. The power line and the cable Check the power connection with the unit is locking connector is not connecting connected properly.
Page 34
Troubleshooting The unit turns on by Remote control may be paired Resynchronize the remote control to connect to a different channel itself. incorrectly. Someone is controlling the hood via Determine who is controlling the hood with the Zephyr Connect app. the app.
Page 35
The temperature of IPM on main PC board is 00 01 too high. Please contact Pacific product support The main PC board generates the IPM-FO signal. 00 02 and provide the fault code. The running current of the main PC board is too low.
Page 36
Product Registration Congratulations on your PACIFIC range hood purchase! Please take a moment to register your new range hood at https://www.2pacific.com/en-us/ productregistration IT’S IMPORTANT Prompt registration helps in more ways than one. Ensures warranty coverage should you need service. Ownership verification for insurance purposes.
Page 62
功能與控制 Control Type Amazon Alexa Voice Commands Description Alexa, Turn on [Hood Name] Turn on range hood power Power Alexa, Turn off [Hood Name] Turn off range hood power Alexa, Increase [Hood Name] Fan Speed Increase fan speed on range hood Alexa, Decrease [Hood Name] Fan Speed Decrease fan speed on range hood Alexa, Set [Hood Name] Fan Speed to [1-6]...