Table of Contents
Advertisement
8
heating function
Under heating mode, press "TEMP" and "CLOCK" buttons simultaneously to start up or turn off 8
this function is started up, "
at 8
. Press "TEMP" and "CLOCK" buttons simultaneously again to exit 8
Note:
Under 8
heating function, fan speed is defaulted at auto speed and it can't be adjusted.
heating function, set temperature can't be adjusted. Press " TURBO " button and the remote controller won't
Under 8
send signal.
Sleep function and 8
cooling mode, press sleep button will cancel 8
the 8
heating function will cancel sleep function.
Under
temperature display, the remote controller will display 46
If "H1" is displayed on the remote controller while it's not operated by the professional person/after-sales person, it belongs to the
misoperation.
Please operate it as below to cancel it.Under the OFF status of remote controller, hold the Mode button for 5s to cancel "H1"
display.
Note:
If remote controller displays "H1", it belongs to the normal function reminder. If the unit is defrosting under heating mode, it
operates according to H1 defrosting mode. "H1" won't be displayed on the panel of indoor unit;
Once you set H1 mode, if you turn off unit by remote controller, H1 will display 3 times on the remote controller and then
disappear;
Also, when you set H1 mode, when you change to heating mode, H1 will display 3 times on the remote controller and then
disappear.
Child lock function
Press "▲" and "
" simultaneously to turn on or turn off child lock function. When child lock function is on, "
displayed on remote controller . If you operate the remote controlle r , the "
the unit.
Temperature display switchover function
Under OFF status, press "
Multi timer function
THREE TIMERS
Press uninterruptedly "LIGHT" button 6 times in 5 seconds thus we enter the "Multi Timer" mode as well as three-minute-
counting-down stars. If three couples of times commands are valid and well-received in 3 minutes, the "Multi Timer" will be
activated along with the success sound of four buzzing, and the former "Multi Timer" settings with be replaced. If not, then
"Multi Timer" mode exits along with the failure sound of six buzzing, and the former "Multi Timer" settings still remain effective.
TWO TIMERS
Press uninterruptedly "LIGHT" button 4 times in 5 seconds thus we enter the "Multi Timer" mode as well as two-minute-counting
-down stars. If two couples of times commands are valid and well-received in 2 minutes, the "Multi Timer" will be activated
along with the success sound of four buzzing, and the former "Multi Timer" settings with be replaced. If not, then "Multi Timer"
mode exits along with the failure sound of six buzzing, and the former "Multi Timer" settings still remain effective.
TIMER CANCELLATION
Press uninterruptedly "LIGHT" button 8 times in 5 seconds all the "Multi Timer"settings will be erased.
Replacement of batteries in remote controller
1. Press the back side of remote controller marked
fig, and then push out the cover of battery box along the arrow direction.
2. Replace two 7# (AAA 1.5V) dry batteries, and make sure the position of
"+" polar and "-" polar are correct.
3. Reinstall the cover of battery box.
NOTE:
During operation, point the remote control signal sender at the receiving window on indoor unit.
The distance between signal sender and receiving window should be no more than 8m, and there should be no obstacles
between them.
Signal may be interfered easily in the room where there is fluorescent lamp or wireless telephone; remote controller should
be close to indoor unit during operation.
Replace new batteries of the same model when replacement is required.
When you don't use remote controller for a long time, please take out the batteries.
If the display on remote controller is fuzzy or there 's no display, please replace batteries.
18
" and "8
" will be shown on remote controller, and the air conditioner keep the heating status
heating function can't operate at the same time. If 8
heating function. If sleep function has been set under cooling mode, start up
" and "MODE" buttons simultaneously to switch temp-erature display between
with "
heating function.
heating function has been set under
heating.
" icon will blink three times without sending signal to
", as shown in the
heating function. When
" icon is
and
signal sender
battery
reinstall
remove
Cover of battery box
Technical Information
.
Advertisement
Table of Contents
