Table of Contents
Advertisement
Sleep3- the sleep curve setting under Sleep mode by DIY could be inquired:
The user could accord to sleep curve setting method to inquire the presetting sleep curve, enter into user individuation sleep
setting status, but do not change the tempera-ture, press "Turbo" button directly for confirmation. Note: In the above presetting or
enquiry procedure, if continuously within 10s, there is no button pressed, the sleep curve setting within 10s, there is no button
pressed, the sleep curve setting status will be automatically quit and resume to display the original displaying. In the presetting or
enquiry procedure, press "ON/OFF" button, "Mode" button, "Timer" button or "Sleep" button, the sleep curve setting
or enquiry status will quit similarly.
9.I FEEL button
Press this button to start I FEEL function and "
controller will send the detected ambient temperature to the controller and the unit will automatically adjust the indoor
temperature according to the detected temperature. Press this button again to close I FEEL function and "
Please put the remote controller near user when this function is set. Do not put
temperature or low temperature in order to avoid detecting inaccurate
When I FEEL function is turned on, the remote controller should be put within the area where indoor unit can receive the
signal sent by the remote controller.
10.TIMER ON / TIMER OFF button
TIMER ON button
"TIMER ON" button can set the time for timer on. After pressing this button, "
remote controller blinks. Press "▲" or
TIMER ON setting will increase or decrease 1min. Hold "▲" or "
until reaching your required time. Press "TIMER ON" to confirm it. The word "ON" will stop blinking. "
resumes displaying. Cancel TIMER ON: Under the condition that TIMER ON is started up, press "TIMER ON"
button to cancel it.
TIMER OFF button
"TIMER OFF" button can set the time for timer off. After pressing this button,"
on remote controller blinks. Press "▲" or
TIMER OFF setting will increase or decrease 1min. Hold "▲" or "
until reaching your required time.
Press "TIMER OFF" word "OFF" will stop blinking. "
Cancel TIMER OFF. Under the condition that TIMER OFF is started up, press "TIMER OFF" button to cancel it.
Note:
Under on and off status, you can set TIMER OFF or TIMER ON simultaneously.
Before setting TIMER ON or TIMER OFF, please adjust the clock time.
After starting up TIMER ON or TIMER OFF, set the constant circulating valid.
After that, air conditioner will be turned on or turned off according to setting time.
ON/OFF button has no effect on setting. If you don't need this function, please use remote controller to cancel it.
11.CLOCK button
Press this button to set clock time. "
Each pressing of "▲" or "
time will change quickly. Release this button when reaching your required time.
Press "CLOCK" button to confirm the time. "
Note:
Clock time adopts 24-hour mode.
The interval between two operation can't exceeds 5s. Otherwise, remote contro- ller will quit setting status. Operation for
TIMER ON/TIMER OFF is the same.
12.QUIET button
Press this button, the Quiet status is under the Auto Quiet mode (display "
(display "
" singal) and Quiet OFF (there is no signal of "
Note:
The Quiet function can be set up in all modes; Under the Quiet mode,the fan speed is not available.
When quiet function is selected:
Under cooling mode: indoor fan operates at notch 4 speed. 10 minutes later or when indoor ambient temperature≤28
, indoor fan will operate at notch 2 speed or quiet mode according to the compari son between indoor ambinet temperature
and set temperature.
Under heating mode: indoor fan operat e s at notch 3 speed or quiet mode according to the comparison between indoor
ambient temperature and set temperature.
Under dry, fan mode: indoor fan operates at quiet mode.
Under auto mode: the indoor fan operates at the auto quiet mode according to
16
" will be displayed on the remote controller. After this function is set, the remote
" button to adjust TIMER ON setting. After each pressing "▲" or "
"
"
" button to adjust TIMER OFF setting. After each pressing "▲" or "
" icon on remote controller will blink. Press "▲" or "
" button, clock time will increase or decrease 1 minute. If hold "▲" or "
" icon stops blinking.
the remote controller near the object of high
ambient temperature.
"
icon disappears and the word "ON" on
" button, 2s later , the time will change quickly
"
" button, 2s later , the time will change quickly
" icon resumes displaying.
,
" and "AUTO" signal ) and Quiet mode
" displayed), after powered on, the Quiet OFF is defaulted.
actual cooling, heating or fan mode.
" will disappear.
" icon
icon disappears and the word "OFF"
" button within 5s to set clock time.
" button, 2s later
Technical Information
" button,
" button,
Advertisement
Table of Contents
