Page 1
Service SR6009 / U1B/N1B/N1SG /K1B Manual AV SURROUND RECEIVER • For purposes of improvement, specifications and design are subject to change without notice. • Please use this service manual with referring to the operating instructions without fail. • Some illustrations using in this service manual are slightly different from the actual set. Ver.
Contents ABOUT THIS MANUAL .............3 Audio Check PASS ..............107 What you can do with this manual ..........3 CLOCK FLOW & WAVE FORM IN DIGITAL BLOCK ...108 Using Adobe Reader (Windows version) ........4 LEVEL DIAGRAM ..............109 SAFETY PRECAUTIONS ............6 BLOCK DIAGRAM ..............115 NOTE FOR SCHEMATIC DIAGRAM .........7 POWER DIAGRAM ..............116 NOTE FOR PARTS LIST ............7...
ABOUT THIS MANUAL Read the following information before using the service manual. What you can do with this manual Search for a Ref. No. (phrase) Jump to the target of a schematic diagram connector (Ctrl+Shift+F) You can use the search function in Acrobat Reader to search for a Ref.
SAFETY PRECAUTIONS The following items should be checked for continued protection of the customer and the service technician. leakage current check Beforereturningthesettothecustomer,besuretocarryouteither(1)aleakagecurrentcheckor(2)alinetochassis resistance check. If the leakage current exceeds 0.5 milliamps, or if the resistance from chassis to either side of the power cord is less than 460 kohms, the set is defective.
NOTE FOR SCHEMATIC DIAGRAM WARNING: Partsindicatedbythe z markhavecriticalcharacteristics.UseONLYreplacementpartsrecommendedbythemanufacturer. CAUTION: Beforereturningthesettothecustomer,besuretocarryouteither(1)aleakagecurrentcheckor(2)alinetochassisresistancecheck. If the leakage current exceeds 0.5 milliamps, or if the resistance from chassis to either side of the power cord is less than 460 kohms, the set is defective. WARNING: DONOTreturnthesettothecustomerunlesstheproblemisidentifiedandremedied.
PRECAUTIONS DURING SERVICE Initializing This Unit Initialize this unit if you have replaced the microcomputer, one of the parts around the microcomputer, or the digital PCB. Press the power button to turn off the power. Hold down buttons "TUNER PRESET -" and "TUNER PRESET +" at the same time and press the power button to turn on the power.
DISASSEMBLY • Remove each part in the order of the arrows below. • Reassemble removed parts in the reverse order. • Read "Precautions During Work" before reassembling removed parts. • If wire bundles are removed or moved during adjustment or part replacement, reshape the wires after completing the work.
Page 12
Explanatory Photos for DISASSEMBLY • The angles from which the photos are taken are shown by "Photo angle: A, B, C, D". • See the diagram below about the shooting direction of each photograph. • Photographs with no shooting direction indicated were taken from the top of the unit. •...
1. FRONT PANEL ASSY TOP COVER → FRONT PANEL ASSY Proceeding : (1) Remove the screws. View from the bottom (2) Cut the wire clamp, then remove the connector wires and FFC. Remove the screws. Front side CN605 CN916 CN916 CX870 Model CN503 CY920 Model...
2. RADIATOR ASSY TOP COVER → FRONT PANEL ASSY → RADIATOR ASSY Proceeding : (1) Remove the screws. View from the bottom (2) Cut the wire clamp. Remove the screws. (3) Remove the connector wire. CN461 CN704 CN702 CN701 CN703...
3. DIGITAL PCB TOP COVER → BACK CHASSIS → DIGITAL PCB Proceeding : (1) Remove the screws. (2) Cut the wire clamp, then remove the connector wires and FFC. CN916 CN903 CN704 STYLE PIN CON1 CON2 CN901 CN914 CX870 Model STYLE PIN CN903 CN704...
4. VIDEO PCB TOP COVER → BACK CHASSIS → DIGITAL PCB → VIDEO PCB Proceeding : (1) Remove the connector wire. Front side BN21B BN28B BN27B PCB HOLDER 5. INPUT PCB TOP COVER → BACK CHASSIS → DIGITAL PCB → VIDEO PCB → INPUT PCB Proceeding : (1) Remove the connector wire.
6. SPK PCB TOP COVER → BACK CHASSIS → DIGITAL PCB → VIDEO PCB → INPUT PCB Proceeding : → SPK PCB (1) Remove the screws. View from the bottom (2) Remove the connector wire. CN461 CN704 CN702 CN701 CN703 (3) Remove the connector wire.
7. SMPS PCB TOP COVER → BACK CHASSIS → DIGITAL PCB → Proceeding : SMPS PCB See "EXPLODED VIEW" for instructions on how to remove each PCB of the "SMPS PCB". 8. TRANS POWER TOP COVER → BACK CHASSIS → DIGITAL PCB → TRANS POWER Proceeding : See "EXPLODED VIEW"...
SPECIAL MODE Special Mode Configuration Buttons No. 1 - 12 : Hold down buttons A, B and C at the same time and press the power button to turn on the power. No. 13 : Press the A and B buttons simultaneously while inserting the AC plug to turn the power on. Mode Button A Button B Button C Contents...
1. Version Display Mode 1.1. Actions Version information is displayed when the device is started in this mode. 1.2. Starting up Hold down buttons "DIMMER" and "STATUS" at the same time and press the power button to turn on the power. Press the "STATUS"...
Page 21
1.4. Error display See the table below for descriptions of displayed errors and countermeasures for these. Display order is q , w , e , r , t , y , u . Condition States Display TROUBLE SHOOTING F I R M E R R O R M A I N * * * * * * * *...
Page 22
1.5. Version Display in the Setup Menu Follow the steps below to display the firmware information. (1) Press the "SETUP" button on the remote control. (2) Select "General - Information - Firmware". The version information is displayed as a 12-digit number as shown in the screenshot below. General/Firmware XXXX-XXXX-XXXX Version...
2. PANEL / REMOTE LOCK Selection Mode 2.1. Actions Turn the PANEL LOCK and REMOTE LOCK modes on and off. 2.2. Starting up Hold down buttons "M-DAX" and "DIMMER" at the same time and press the power button to turn on the power. Select the mode using the button "TUNER PRESET CH+", and press the button "STATUS"...
3. Selection Modes for Service-related Operations 3.1. Actions Select diagnostic mode (service path check mode), protection history display mode, or 232C standby clear mode. 3.2. Starting up Hold down buttons "ZONE2 SOURCE" and "STATUS" at the same time and press the power button to turn on the power. 3.3.
Page 26
3.4 PROTECTION DIAGRAM PAMP PCB DIGITAL PCB TR_THERMAL uCOM DC 113pin/PD4 PROTECTION LOGIC ASO 112pin/PD5 ⇒ L_activeshutdown ⇒ L_activeshutdown THER PROTF ⇒ L_activeshutdown TR_THERMAL THER PROTB ⇒ L_activeshutdown THER_PROT_E 66pin/P77 THER PROTA ⇒ L_activeshutdown THER_PROT_F 81pin/PB5 THER_PROT_A 125pin/P95 THER_PROT_B 126pin/P94 TR_THERMAL CURRENT (After 90sec ) CURRENT DET 144pin/IRQ8-B...
Page 27
3.5. DIAGNOSTIC MODE (Service Path Check Mode) 3.5.1. Actions This function is convenient for confirming problem paths in the product and executing a path check after repair. The Video and Audio paths can be checked. The backup data is not rewritten. 3.5.2.
Page 28
3.5.6. Audio system confirmation items fig. XX: See the block diagram of the fig.XXth. Paths confirmation item Display Settings Contents of confirmation Remarks Analog Input Source : CBL/SAT ・Analog input ⇒ Speaker output (FRONT L,R) A 0 1 : A N A L O G P A S S Input Mode : ANALOG(fixed) ・Analog input ⇒...
DIAGNOSTIC PATH DIAGRAM SR6009 ANALOG VIDEO BLOCK fig.01 CBL/SAT CBL/SAT_V DVD_V CVBS IN GAME Blu-Ray_V V.AUX(FRONT) V.AUX_V CVBS MONITOR COMPONENT OUT Y CBL/SAT_Y COMPONENT OUT PB CBL/SAT CBL/SAT_PB COMPONENT OUT PR CBL/SAT_PR NJM2595MTE1 V_AUX_V DVD_Y CBL/SAT_V COMPONENT IN DVD_V DVD_PB Blu-Ray_V DVD_PR NJM2586AVC3...
Page 30
SR6009W ANALOG VIDEO BLOCK fig.02a CBL/SAT CBL/SAT_V DVD_V CVBS IN GAME Blu-Ray_V V.AUX(FRONT) V.AUX_V CVBS MONITOR COMPONENT OUT Y CBL/SAT_Y COMPONENT OUT PB CBL/SAT CBL/SAT_PB COMPONENT OUT PR CBL/SAT_PR NJM2595MTE1 V_AUX_V DVD_Y CBL/SAT_V COMPONENT IN DVD_V DVD_PB Blu-Ray_V DVD_PR NJM2586AVC3 DEC_CVBS_IN CH1 IN1 CBL/SAT_Y...
Page 59
3.6. Protection History Display Mode 3.6.1. Actions This mode records and displays an event in which the THERMAL, CURRENT, ASO or DC protection was activated. If protections have been activated multiple times, the latest protection operation is recorded. 3.6.2. Starting up Hold down buttons "ZONE2 SOURCE"...
Page 60
3.6.4. Clearing the Protection History There are two ways to clear the protection history. (1) Start Protection History Display Mode. Press the button "STATUS" to display the protection history. Press and hold the button "DIMMER" for 3 seconds. P R O T E C T H I S T O R Y : D C Press and hold the button "DIMMER"...
Page 61
3.8. Operation Info Mode 3.8.1. Actions This mode displays the accumulated operating time, power on count and each protection count. 3.8.2. Starting up Hold down buttons "ZONE2 SOURCE" and "STATUS" at the same time and press the power button to turn on the power. Select the "4.
Page 62
3.9. TUNER STEP mode 3.9.1. Actions This is a special mode for enabling reception STEP of the ANALOG TUNER to be changed. 3.9.2. Starting up Hold down buttons "ZONE2 SOURCE" and "STATUS" at the same time and press the power button to turn on the power. Select the "5.
4. Protection Pass Mode 4.1. Actions • This mode allows the power to be turned on without activating protections. • This is the same as normal power-on, except that protections are not activated. 4.2. Operations Hold down buttons "DIMMER", "STATUS" and "SOUND MODE" at the same time and press the power button to turn on the power.
6. CX870 / CY920 Initialization mode 6.1. Actions The following items are initialized. (1) Favorites (2) Quick Select (3) Presets (4) Internet Radio Recently Played (5) Flickr contacts (6) User ID (7) Resume Playback station 6.2. Operations Hold down buttons "TUNER PRESET CH -" and "DIMMER" for at least 3 seconds while the power is on. Initializing Display I n i t i a l W a i t...
JIG FOR SERVICING The following jigs (extension cable kit) are used when repairing the PCBs. Order the jigs from your dealer if necessary. CAUTION : Incorrect connections may cause malfunction. • Connection of Jig for DIGITAL PCB -Items to Be Prepared- 8U- 110084S EXTENSION UNIT KIT 1 Set...
Page 66
Front side BN21B BN28B BN27B PCB HOLDER Front side TO CN461 BN26B CN706A BN64C BN23C (3) Remove the DIGITAL PCB from the chassis and turn it over. Place an insulation sheet larger than the PCB underneath the DIGITAL PCB. Connect the earth of the PCB to the chassis using an earth wire, etc. PCB INPUT PCB VIDEO PCB DIGITAL...
Page 67
(4) Connect the expansion cables. PCB FRT CNT PCB HDMI PCB SIDE CNT PCB FRT CNT PCB VIDEO PCB SIDE CNT PCB FRT CNT PCB SIDE CNT PCB VIDEO Connection table of Board to Board Ref. No. Ref. No. 15pin CN27A SIDE CNT BN27A...
PROCEDURE AFTER REPLACING THE MICROPROCESSOR, ETC. The procedure after replacing the u-COM (microprocessor), flash ROM, etc. is as follows. Procedure after PCB Name Ref. No. Description Remark Replacement R5F56108VNFP SOFTWARE: Main DIGITAL IC151 DIGITAL IC171 R5F5210ABDFP SOFTWARE: Sub MX25L1606EM2I-12G SOFTWARE: DSP ROM DIGITAL IC253 MX25L12845EMI-10G...
Page 69
1.2. Unzip Download File Unzip the downloaded file on your computer. SRXXXXXXX USB_SRXXXXXXX_XXXXXXXXXXXX-XXXX.zip copy to USB flash drive You can find "firmwares" folder after unzipped. Copy that folder to USB flash drive. You have to put "firmwares" folder on root directly on USB flash drive(memory). 1.3.
Page 70
1.4. Insert the USB memory in the USB port. NOTE:Remove the LAN cable from this unit when performing updates. Download firmware in USB flash drive. 1.5. Start the update. Hold down buttons "TUNER PRESET CH +" and "STATUS" at the same time and press the power button to turn on the power.
Page 71
1.9 Forced USB All Device Write Mode 1.9.1. Actions Mode used when this unit cannot be recovered. Forcibly switches this unit to USB update mode. 1.9.2. Operations Press the "TUNER PRESET CH +" and "STATUS" buttons simultaneously while inserting the AC plug to turn the power 1.9.2. The firmware update finishes.
Page 72
1.11. About the error code See the table below for error codes and details of faults when the firmware is updated through USB memory. Error USB Update Error Display Details of Error code Coping strategies Code C o n n e c t i o n F a i l Disconnect and connect the USB Unable to detect USB.
Page 73
Error USB Update Error Display Details of Error code Coping strategies Code This unit automatically retries several times. Wait until the FL display stops. U p d a t i n g f a i l Block Write failed while rewriting If the FL display stops at the Error dis- Main.
Page 74
Error USB Update Error Display Details of Error code Coping strategies Code This unit automatically retries several times. Wait until the FL display stops. C o n n e c t i o n F a i l Time Out in USB Check. If the FL display stops at the Error dis- play, press and hold the "Power opera- tion"...
Page 75
Error USB Update Error Display Details of Error code Coping strategies Code This unit automatically retries several NACK received in response or no times. Wait until the FL display stops. U p d a t i n g f a i l response from Sub for L com- If the FL display stops at the Error dis- mand.
Page 76
Error USB Update Error Display Details of Error code Coping strategies Code This unit automatically retries several Abnormal data in Update Packet times. Wait until the FL display stops. U p d a t i n g f a i l received from CX870 / CY920 If the FL display stops at the Error dis- (PacketNoError).
Page 77
Error USB Update Error Display Details of Error code Coping strategies Code This unit automatically retries several times. Wait until the FL display stops. U p d a t i n g f a i l Failed to transit to Application If the FL display stops at the Error dis- Mode.
2. Updating by DPMS Download the latest firmware from the internet and update the firmware. 2.1. Network Connection (1) System Requirements • A broadband internet connection • Modem • Router • Ethernet cable (CAT-5 or greater recommended) (2) Settings Internet Computer Modem ComputerLAN port / Ethernet connector...
Page 79
2.3. About the error code See the following table for details on the error code, details of the error code, display and coping strategies when updating the firmware from DPMS. (DPMS:maranz Product Management Server). Error DPMS Update Error Display Details of Error code Coping strategies Code Initialize the unit and try updating...
Page 80
Error DPMS Update Error Display Details of Error code Coping strategies Code Abnormal data in Update Packet U p d a t i n g f a i l Turn on the power again. Update will received from CX870 (PacketNo- start automatically.
Page 81
Error DPMS Update Error Display Details of Error code Coping strategies Code Check the network connection. Update C o n n e c t i o n F a i l Connect Time Out by DPMS con- in an environment where there is a nection.
Page 82
Error DPMS Update Error Display Details of Error code Coping strategies Code NACK received in response or no U p d a t i n g f a i l Turn on the power again. Update will response from Sub for L com- start automatically.
Page 83
Error DPMS Update Error Display Details of Error code Coping strategies Code Check the network connection. Update C o n n e c t i o n F a i l IP Address acquisition failure in an environment where there is a (Time Out).
Page 84
Device display during firmware update Display of target device during firmware update. Target device DPMS Update Display Error code when an error occurs M a i n 10 - 16 Main CPU * * * m i n 36 - 3F * * % 50 - 52 54 - 58...
ADJUSTMENT Adjusting Idling Current 1. Preparation (1) Prepare a DV voltmeter. (2) Place the unit in normal usage conditions, away from highly ventilated areas such as next to an air conditioning machine or electric fan. The set requires an ambient temperature of 15℃ to 30℃ and standard humidity. (3) Settings of This Unit •...
SURROUND MODES AND PARAMETERS Contents Connections Playback Settings Tips Appendix Sound modes and channel output S This indicates the audio output channels or surround parameters that can be set. D This indicates the audio output channels. The output channels depend on the settings of “Speaker Config.” (v p. 196). Channel output Sound mode (v p.
Page 87
Contents Connections Playback Settings Tips Appendix Surround Parameter (v p. 158) Neo:X Audyssey (v p. 164) Pro Logicg/gx Music mode only mode Tone M-DAX only Sound mode (v p. 122) (v p. (v p. Panorama Dimension Center Center Dynamic Dynamic Audyssey MultEQ ®...
Page 88
Contents Connections Playback Settings Tips Appendix Types of input signals, and corresponding sound modes F This indicates the default sound mode. S This indicates the selectable sound mode. 2-channel signal Multi-channel signal Analog / Dolby DTS-HD DTS ES DTS ES Dolby Dolby Dolby...
TROUBLE SHOOTING 1. POWER 1.1. The unit does not power on The unit does not power on Does the power indicator on Does the power indicator on the the front panel flash in green front panel flash in red when the or white when the power is power is turned on? turned on?
2. Analog video COMPONENT/HDMI OUT NG Input CVBS Input COMPONENT Input Function : CBL / SAT Function : CBL / SAT HDMI TO "3 HDMI/DVI" To A <DIGITAL PCB> test point JK382 T222 JK394 JK393 JK392 JK391 JK384 JK383 JK381 T224 BN111 C4371...
Page 91
Input CVBS / COMPONENT Check the input signal to the VIDEO DECODER. Can a signal be confirmed at the following points? DIGITAL PCB Check the connection between Input CVBS:Check B : R3527 the PCBs. Input COPONENT:Check C COMPONENT-Y : R3530 COMPONENT-Cb : R3528 COMPONENT-Cr : R3529...
Page 92
Input CVBS Check the set value of each IC. Are the voltage values as follows? DIGITAL PCB The DIGITAL PCB is faulty. BN21A - 6pin : Hi(3.3V) BN21A - 7pin : Hi(3.3V) BN21A - 9pin : Lo(0V) Use the jigs to extend the DIGITAL PCB.
Page 93
Input COMPONENT Check the set value of each IC. Are the voltage values as follows? The DIGITAL PCB is faulty. DIGITAL PCB BN21A - 4pin : Lo(0V) BN21A - 3pin : Hi(3.3V) Use the jigs to extend the DIGITAL PCB. Is the power supply voltage Check the connection between the being output correctly?
3. HDMI/DVI 3.1. No picture or sound is output (HDMI to HDMI) No picture or sound is output. Check the connection of the HDMI/DVI cable. (1) Is the HDMI/DVI cable correctly inserted? Check the connection of the HDMI/DVI cable. (2) Is an HDMI/DVI selector, repeater or image quality improvement Remove all of these and connect only the HDMI/DVI device being used? cable.
Page 95
(11) Are a picture and sound output when a different Blu-ray/DVD The Blu-ray/DVD player is faulty. player is used? Check the TV. Use a TV that supports HDCP. Computer monitors can- (12) Does the TV support HDCP? not be used. If the TV does not support 1080P/4K, a picture cannot be (13) Does the TV support 1080P/4K? output even if the Blu-ray/DVD player is set to 1080P/4K.
4. AUDIO 4.1. AUDIO CHECK No audio output See "Audio Check PATH" (107 page). CHECK1 INPUT SURROND MODE SOURCE Check the ANALOG AUDIO BLOCK Audio output OK? ANALOG 2CH DIRECT ANALOG CHECK2 INPUT SURROND MODE SOURCE Check the DIGITAL AUDIO Legacy BLOCK Audio output OK?
Page 97
4.2. Power AMP (AMP PCB) No audio output. Protection is activated. Is the power transistor open or short circuit- Replace the power transistor. 2SB1647/2SD2560 Is the emitter resistor of the power transistor open? Replace the emitter resistor. 0.47Ω Is the base resistor of the power transistor open? Replace the base resistor.
Page 98
4.3. Analog audio No audio output. Is a voltage of ±7V supplied to SIDE Repair the ±7V power supply. CNT PCB CN64C 4-7pin? Is there an audio signal in INPUT Repair the power amplifier. PCB CN461? Connect the connectors correctly. Is electron volume serial data be- Is the connector correctly connected ing sent to SIDE CNT PCB CN23C...
5. Network/Bluetooth/USB 5.1. Cannot connect to the network Check the connection environment Insert the LAN cable correctly and then turn Is the LAN cable correctly inserted? on the power again. Check the connection environment Set the IP address, etc. correctly. If the IP settings are fixed, check that no Are the network settings of this unit correct? other devices have the same IP address and...
Page 100
Can an output voltage (3.3V) to Is E_POWER1 (IC151 uCOM 53pin) The circuit of E_POWER1 between Q1252(FET_SW) be confirmed? "Hi" ? IC151 and Q1252 are faulty. The circuit around Q1252(FET_SW) is faulty. Can an output voltage (1.2V) to IC115 Is E_POWER4 (IC151 uCOM 56pin) The circuit of E_POWER4 between be confirmed? "Hi"...
Page 101
5.2.1. Cannot connect to the Bluetooth (Case of CX870 model) Check the Bluetooth Is the Bluetooth device compatible with the A2DP profile? Use a device that is A2DP profile compatible. Enable the Bluetooth function and try connecting Is the Bluetooth function enabled on the Bluetooth device? again.
Page 102
5.2.2. Cannot connect to the Bluetooth (Case of CY920 model) Check the Bluetooth Is the Bluetooth device compatible with the A2DP profile? Use a device that is A2DP profile compatible. Enable the Bluetooth function and try connecting Is the Bluetooth function enabled on the Bluetooth device? again.
Page 103
5.3. A connected USB device is not recognized. Check the USB device being used Is a USB hub being used? Do not use a USB hub. Is the USB device supported by this unit? This unit supports devices in the FAT16 and FAT32- formatted mass storage class, MTP-compatible devices and iPods (with the exception of some models).
6. SMPS DC 5V is not output. Replace the IC901 (TOP256YN) and Is IC901 (TOP256YN) damaged? D9001 / D9002 / D9003 / D9004. Are there the damage in IC901 and Has a fuse (F9001) broken? Replace the damaged part(s). D9001 / D9002 / D9003 / D9004 / C9004? Are there any short circuits caused by Repair the short circuited area(s) by the...
Page 106
Operation waveform for each part OPTION AC100 ~ 120V CCQF2E104KZE-T Primary drain After primary side rectification AC220 ~ 240V OPEN (Caution: High voltage, electric shock) (Caution: High voltage, electric shock) C9002 0.01uF 250V OPTION HEATSINK (16*16*30) D9001 1N4007 or CHASSIS After secondary rectifications D9002 1N4007 D9012...
LEVEL DIAGRAM SR6009 LEVEL DIAGRAM FRONT ch R2A15218FP ANALOG H/P OUT SPEAKER LINE IN HDAM + GAIN ADJ. + MUTE PRE OUT PCM1690 + PCM9211 + (N Only) - - +30dB 4.22Vrms:A/D FULL SCALE SP OUT R2A15218FP MAX. OUTPUT 3.8Vrms 4.48Vrms/8Ω...
Page 110
SR6009 LEVEL DIAGRAM CENTER ch R2A15218FP HDAM + SPEAKER GAIN ADJ. MUTE PRE OUT PCM1690 + + (N Only) - - +30dB SP OUT R2A15218FP MAX. OUTPUT 3.8Vrms 4.48Vrms/8Ω Differential Out PCM1690 2.83Vrms=0dBFS MAX. SIGNAL LEVEL +20dB +20dB DOLBY LIMIT LEVEL (ALLch-3dBFS) +29dB -10dBFS +10dB...
Page 111
SR6009 LEVEL DIAGRAM SUBWOOFER ch R2A15218FP HDAM MUTE PRE OUT GAIN ADJ. PCM1690 + + - - +30dB MAX. SIGNAL LEVEL R2A15218FP MAX. OUTPUT 3.8Vrms Differential Out PCM1690 DOLBY LIMIT LEVEL (ALLch-3dBFS) 2.83Vrms=0dBFS +20dB +20dB -10dBFS +10dB +10dB PREOUT 310mVrms -20dBFS 200mVrms PRE OUT...
Page 112
SR6009 LEVEL DIAGRAM SURROUND ch R2A15218FP SPEAKER HDAM + GAIN ADJ. MUTE PRE OUT PCM1690 + + (N Only) - - +30dB SP OUT R2A15218FP MAX. OUTPUT 3.8Vrms 4.48Vrms/8Ω Differential Out PCM1690 2.83Vrms=0dBFS MAX. SIGNAL LEVEL +20dB +20dB DOLBY LIMIT LEVEL (ALLch-3dBFS) +29dB -10dBFS +10dB...
Page 113
SR6009 LEVEL DIAGRAM SURR.BACK/FRONT HEIGHT/FRONT WIDE ch R2A15218FP SPEAKER HDAM + GAIN ADJ. MUTE PRE OUT PCM1690 + + (N Only) - - +30dB SP OUT R2A15218FP MAX. OUTPUT 3.8Vrms 4.48Vrms/8Ω Differential Out PCM1690 2.83Vrms=0dBFS MAX. SIGNAL LEVEL +20dB +20dB DOLBY LIMIT LEVEL (ALLch-3dBFS) +29dB -10dBFS...
Page 114
SR6009 LEVEL DIAGRAM ZONE2 R2A15218FP from F-ch from D/A To MAIN SPEAKER SB-ch + LINE IN ZONE GAIN ADJ. NJW1194 MONO TONE MUTE PRE OUT PCM5100 MONO +30dB SP OUT R2A15218FP MAX. OUTPUT 3.8Vrms 4.48Vrms/8Ω PCM5100 MAX. SIGNAL LEVEL 2.0Vrms=0dBFS +20dB +20dB +29dB...
TO 0C TO A3 TO A5 R1571 4.7K R1572 4.7K 4.7K R1573 R1574 OPEN R1575 OPEN R1576 OPEN R1577 OPEN OPEN R1578 R1579 OPEN M3.3V SWM3.3V DGND MAINPOWER MAINPOWER M_RESET M_RESET BDOWN BDOWN REMOTEPOWER REMOTEPOWER C1510 R1546 33 CPUPOWER ACK_SIMO CPUPOWER SCPUPOWER SCPUPOWER...
TO 1D TO 2D TO 3D TO 4D TO F6 TO 5D SCPU5V DGND R1781 OPEN SCPU3.3V R1782 OPEN SUBBDOWN R1783 4.7K SUBBDOWN TO B8 CEC_POWER R1784 4.7K CEC_POWER R1785 4.7K DV_POWER2 DV_POWER2 R1786 4.7K DV_POWER1 DV_POWER1 R1787 4.7K DA_POWER DA_POWER SCPU Z2PLDAERR...
ANALOG VDIEO PART OPEN BLU-RAY CBL/SAT IC511 NJM2595MTE1 MONITOR_OUT VIDEO+5V R5113 75(1%) TO 0G VGND R5114 JK511 BLU-RAY_CVBS_IN OPEN C5111 VIDEO-5V CBL/SAT 10/50V C5112 DVD_CVBS_IN 10/50V R5119 Q5117 75(1%) R5116 OPEN MONITOR OUT CVTRT1N141C CBL/SAT_CVBS_IN R5117 75(1%) R5115 AUX_CVBS_IN C5121 V.AUX_V_IN MEDIA PLAYER R5121...
R9821 TUNER PART R9825 C9827 OPEN OPEN C9821 C9825 OPEN L9821 OPEN OPEN R9823 R9827 OPEN C9809 OPEN C9810 OPEN CHASSIS C9828 R9826 OPTION A OPEN OPEN C9826 C9811 L9822 OPEN OPEN 0.1uF R9824 CHASSIS R9828 OPEN C9822 OPEN TU901 TUNER_L L-OUT TUNER_R...
EXPLODED VIEW Please see the last chapter for the part list. S17 X2 C42-1 C42-2 S10 x2 S8 x2 S5 x21 CX870 ONLY CY920 ONLY S3 X2 S3 X2 P18 x3 CX870 ONLY S2 x4 WARNING: Parts marked with this symbol z have critical characteristics. Use ONLY replacement parts recommended by the manufacturer.
SEMICONDUCTORS Only major semiconductors are shown, general semiconductors etc. are omitted to list. The semiconductor which described a detailed drawing in a schematic diagram are omitted to list. 1. IC's R5F56108VNFP (HDMI : IC151) PE0/D8 PC4/A20 PD7/D7 PC5/A21/SCK5/CS5#-D PD6/D6 PC6/A22/RxD5/CS6#-D PD5/D5 PC7/A23/TxD5/CS4#-D/CS7#-D PD4/D4...
Page 161
Pull up/ Pin Name Symbol LvCnv STBY STOP Function down STBY 17 P86 (CEC POWER2) Reserve (CEC POWER2 control) R E M O T E 232C POWER SUPPLY (REMOTE 18 P85 POWER(232C) 3.3V) control pin.(ON: H) 19 RES# RESET Reset input (reset: L) 20 XTAL XTAL Clock input...
Page 162
Pull up/ Pin Name Symbol LvCnv STBY STOP Function down STBY ETHERNET communication control pin 55 P54/TRDATA0 E SPI MIEO N3VPu (DM860) ETHERNET communication control pin 56 P83 E SPI CLK N3VPu (DM860) 57 VSS 58 P82/TRCLK FL CE VFD control pin 59 VCC +3.3V 60 P81/TRSYNC...
Page 163
Pull up/ Pin Name Symbol LvCnv STBY STOP Function down STBY P A 3 / A 3 / P O 1 9 / D A C ( E T H E R ) DAC (ETHER) MUTE control pin T I O C C 6 / T I O C D 6 / MUTE (PCM5100 for DM860) TCLKF...
Page 164
Pull up/ Pin Name Symbol LvCnv STBY STOP Function down STBY HDMI INPUT 5V (for EDID / HOT 139 P41/IRQ9-B/AN1 HDMI IN 5V SET PLUG) detection pin 140 AVSS AVSS 141 P40/IRQ8-B/AN0 CEC_IN SW3VPu CEC-D signal input pin Reference voltage (+3.3V) input pin for 142 VREF VREF A/D port...
Page 165
RX210 Group 1. Overview R5F5210ABDFP (HDMI : IC171) RX210 Group PLQP0100KB-A (100-pin LQFP) (Top view) VREFL0 VREFH0 AVCC0 AVSS0 R5F5210ABDFP Terminal Functions Note: • This figure indicates the power supply pins and I/O port pins. For the pin configuration, see the table “List of Pins and Pin Functions (100-Pin LQFP)”.
Page 166
Symbol Pin Name Pu/Pd STBY Function LvCnv STBY 34 P12/SCL/IRQ2 778_1_RST HDMI MN8647781(TX) RESET control pin ※ 35 PH3 HSDA HDMI I2C- MN8647781 3VPu 36 PH2/IRQ1 HSCL HDMI I2C- MN8647781 3VPu 37 PH1/IRQ0 778_1_HINT HDMI MN8647781(TX) HDMI INT input pin 38 PH0 778_2_RST HDMI MN8647781(RX) RESET control pin...
Page 167
Symbol Pin Name Pu/Pd STBY Function LvCnv STBY 85 PD1/IRQ1 DSP1CS DSP control pin (ADSP21487KSWZ-3B) 3VPu 86 PD0/IRQ0 DSP1FLAG0 DSP control pin (ADSP21487KSWZ-3B) 87 P47/AN007 88 P46/AN006 VIN A COMPOSITE VIDEO SELECT IC(NJM2595) 89 P45/AN005 VIN B COMPOSITE VIDEO SELECT IC(NJM2595) 90 P44/AN004 VIN C COMPOSITE VIDEO SELECT IC(NJM2595)
Page 173
A3V56S30FTP A3V56S40FTP 256M Single Data Rate Synchronous DRAM A3V64S40GTP-60 Pin Function Pin Descriptions SYMBOL TYPE DESCRIPTION Clock: CLK is driven by the system clock. All SDRAM input signals are sampled on the positive edge of CLK. CLK also increments the internal burst counter and controls the output registers. Input Clock Enable: CKE activates (HIGH) and deactivates (LOW) the CLK signal.
Page 174
A3V56S30FTP A3V56S40FTP 256M Single Data Rate Synchronous DRAM A3V64S40GTP-60 Block Diagram Note:This figure shows the A3V56S30FTP The A3V56S40FTP configuration is 8192x512x16 of cell array and DQ0-15 Type Designation Code A 3V 56 S40F TP-G6 Speed Grade 75: 133MHz@CL=3 7: 143MHz@CL=3 6:...
Page 176
SLAS764 – MAY 2011 www.ti.com DEVICE INFORMATION TERMINAL FUNCTIONS, PCM510x PCM5100 (DIGITAL:IC203) PCM510X (top view) Table 2. TERMINAL FUNCTIONS, PCM510x TERMINAL DESCRIPTION NAME CPVDD Charge pump power supply, 3.3V CAPP Charge pump flying capacitor terminal for positive rail CPGND Charge pump ground CAPM Charge pump flying capacitor terminal for negative rail VNEG...
Page 177
PCM1690(DIGITAL:IC301) PCM1690 Pin Function TERMINAL PULL- DESCRIPTION NAME DOWN TOLERANT RSV2 — — — Reserved, tied to analog ground RSV1 — — — Reserved, left open RSV2 — — — Reserved, tied to analog ground RSV1 — — — Reserved, left open RSV2 —...
Page 178
TERMINAL PULL- DESCRIPTION DOWN TOLERANT NAME VOUT1+ Positive analog output from DAC1 VOUT1- Negative analog output from DAC1 PCM1690 RSV2 — — — Reserved, tied to analog ground AGND2 — — — Analog ground 2 VCC2 — — — Analog power supply 2, +5 V RSV2 —...
Page 179
CONFIDENTIAL 8-CHANNEL ELECTRONIC VOLUME With 11-Input selector And Tone control BLOCK DIAGRAM AND PIN CONFIGURATION (TOP VIEW) R2A15218FP (INPUT : IC471) AVCC MUTE AVCC N.C. AVEE AVEE N.C. TREL 0/-6/-12/-18dB ADCL BASSL2 BASSL1 ADCR N.C. AGND Bass/ Treble 0~-95dB, -14~+14dB -∞...
Page 180
R2A15218FP R2A15218FP CONFIDENTIAL 8-CHANNEL ELECTRONIC VOLUME With 11-Input selector And Tone control PIN DESCRIPTION R2A15218FP Pin Function PIN No. Function Name 23,21, FROUT,FLOUT, 17,15, COUT,SWOUT, Output pin of FL/FR/C/SW/SL/SR/SBL/SBR channel 11,9, SROUT, SLOUT, SBROUT,SBLOUT 24,20, FRC,FLC, 18,14, CC,SWC, Connects capacitor for reducing click noise of 12,8, SRC,SLC, L/R/C/SW/SL/SR/SBL/SBR channel volume...
Page 183
FRONT FRONT PCB ASS'Y ※Parts indicated by "nsp"on this table cannot be supplied. ※The parts listed below are only for maintenance. Therefore they might differ from the parts used in the unit in appearances or dimensions. NOTE:The symbols in the column Remarks indicate the following destinations. U : North America model N : Europe model K : China model F : Japan model B : Black model SG : Silver Gold model...
Page 184
FRONT REF No. Part No. Part Name Remarks Q'ty New OTHER PARTS GROUP BK601 BRACKET,VFD CMD1A793 BK604,605 BRACKET,PCB CMD1A629 BN605 WIREASS'Y(5P,2.0MM,600MM,UL2725#24/#28,1P+2C)USB CWB8A005600HC EXPLODED_C2 BN63A WIREASS'Y,(5P,100mm,2mmPITCH,UL1007,#24) CWB1C005100CC BU601 SUPPORT,IR CHG1A533 CN605 WAFER/ANGLE/2.5mm/07P CJP07GB03ZY CN69A WAFER,FFC(40P-1mm,ANGLE) CJP40GB284ZN ! F6001 943652500550D FUSE(372Series/200mA/TR5) CBA2D0200A3EYT FL601 172010008005S CFLGP1261AI...
Page 185
AMP PCB ASS'Y ※Parts indicated by "nsp"on this table cannot be supplied. ※The parts listed below are only for maintenance. Therefore they might differ from the parts used in the unit in appearances or dimensions. NOTE:The symbols in the column Remarks indicate the following destinations. U : North America model N : Europe model K : China model F : Japan model B : Black model SG : Silver Gold model...
Page 188
REF No. Part No. Part Name Remarks Q'ty New R7744 RES,CHIP(3216/5%/22Kohm) CRJ14CJ223T R7745 RES,CARBON(1/5W,22Kohm,J) CRD20TJ223T CAPACIITORS GROUP C7001 CAP,CHIP(1608,50V/0.01uF,X7R)_SAMSUNG CCUS1H103KCS C7011,7012 CAP,ELECT(10V/330uF) CCEA1AH331T C7013 CAP,ELECT(10V/47uF) CCEA1AH470T C7101 00D2544574919 CAP,ELECT(50V/47uF),ELNA/RA3 CCEA1HRA3470T C7102 CAP,PE-FILM(100V/470pF/J) CCME2A471JR11T C7104 CAP,PE-FILM(100V/220pF/J) CCME2A221JR11T C7106 00D2544569937 CAP,ELECT(25V/220uF,ELNA/RA3) CCEA1ERA38P221T C7107 CAP,MYLAR(50V/2200pF/J) HCQI1H222JZT...
Page 189
INPUT INPUT PCB ASS'Y ※Parts indicated by "nsp"on this table cannot be supplied. ※The parts listed below are only for maintenance. Therefore they might differ from the parts used in the unit in appearances or dimensions. NOTE:The symbols in the column Remarks indicate the following destinations. U : North America model N : Europe model K : China model F : Japan model B : Black model SG : Silver Gold model...
Page 193
VIDEO VIDEO PCB ASS'Y ※Parts indicated by "nsp"on this table cannot be supplied. ※The parts listed below are only for maintenance. Therefore they might differ from the parts used in the unit in appearances or dimensions. NOTE:The symbols in the column Remarks indicate the following destinations. U : North America model N : Europe model K : China model F : Japan model B : Black model SG : Silver Gold model...
Page 194
SPK PCB ASS'Y ※Parts indicated by "nsp"on this table cannot be supplied. ※The parts listed below are only for maintenance. Therefore they might differ from the parts used in the unit in appearances or dimensions. NOTE:The symbols in the column Remarks indicate the following destinations. U : North America model N : Europe model K : China model F : Japan model B : Black model SG : Silver Gold model...
Page 196
CNT PCB ASS'Y ※Parts indicated by "nsp"on this table cannot be supplied. ※The parts listed below are only for maintenance. Therefore they might differ from the parts used in the unit in appearances or dimensions. NOTE:The symbols in the column Remarks indicate the following destinations. U : North America model N : Europe model K : China model F : Japan model B : Black model SG : Silver Gold model...
Page 197
SMPS SMPS PCB ASS'Y ※Parts indicated by "nsp"on this table cannot be supplied. ※The parts listed below are only for maintenance. Therefore they might differ from the parts used in the unit in appearances or dimensions. NOTE:The symbols in the column Remarks indicate the following destinations. U : North America model N : Europe model K : China model F : Japan model B : Black model SG : Silver Gold model...
Page 198
F-HDMI F-HDMI PCB ASS'Y ※Parts indicated by "nsp"on this table cannot be supplied. ※The parts listed below are only for maintenance. Therefore they might differ from the parts used in the unit in appearances or dimensions. NOTE:The symbols in the column Remarks indicate the following destinations. U : North America model N : Europe model K : China model F : Japan model B : Black model SG : Silver Gold model...
Page 199
N CX870 Model CVIANAM2048AV ┗IC151 943243102280M R5F56108VNFP (MAIN CPU for CY920) U CY920 Model CVIANAM2014AV IC152 943239101500S I.C,EEPROM(128KBIT,SOP-8P) CVIR1EX24128BSAS 1 IC171 I.C,CPU(32BIT,1MFLASH) CVIR5F5210ABDFP ┗IC171 943243102860S I.C,SUBCPU(SR6009/U1B) CVIANAM2015AV ┗IC171 943243102890S I.C,SUBCPU(SR6009/N) CVIANAM2023AV IC191 00D2623448908 I.C,3STATEQUADBUFFER CVITC74VHC125FT IC201 943236101350D I.C,DIR/DIT(WITHADC,LQFP-48P) CVIPCM9211PTR IC202 943236101520D I.C,DIR(SSOP-16)
Page 200
DIGITAL REF No. Part No. Part Name Remarks Q'ty New R1115 RES,CHIP(1608/1%/169Kohm) CRJ10DF1693T R1116 RES,CHIP(1608/5%/0ohm) CRJ10DJ0R0T R1122 RES,CHIP(1608/5%/4.7Kohm) CRJ10DJ472T R1123 RES,CHIP(1608/5%/100Kohm) CRJ10DJ104T R1124 RES,CHIP(1608/1%/348Kohm) CRJ10DF3483T R1125 RES,CHIP(1608/1%/76.8Kohm) CRJ10DF7682T R1126 RES,CHIP(1608/5%/0ohm) CRJ10DJ0R0T R1129 RES,CHIP(1608/5%/10ohm) CRJ10DJ100T R1131 RES,CHIP(1608/5%/82Kohm) CRJ10DJ823T R1133 RES,CHIP(1608/5%/100Kohm) CRJ10DJ104T R1134 RES,CHIP(1608/1%/348Kohm) CRJ10DF3483T...
Page 201
DIGITAL REF No. Part No. Part Name Remarks Q'ty New R1720 RES,CHIP(1005/5%/33ohm) CRJ06IJ330T R1721 RES,CHIP(1005/5%/10Kohm) CRJ06IJ103T R1722-1724 RES,CHIP(1005/5%/33ohm) CRJ06IJ330T R1726-1730 RES,CHIP(1005/5%/33ohm) CRJ06IJ330T R1731 RES,CHIP(1005/5%/4.7Kohm) CRJ06IJ472T R1732 RES,CHIP(1005/5%/33ohm) CRJ06IJ330T R1734-1736 RES,CHIP(1005/5%/33ohm) CRJ06IJ330T R1739-1743 RES,CHIP(1005/5%/33ohm) CRJ06IJ330T R1747 RES,CHIP(1005/5%/4.7Kohm) CRJ06IJ472T R1751 RES,CHIP(1005/5%/10Kohm) CRJ06IJ103T R1752 RES,CHIP(1005/5%/100Kohm) CRJ06IJ104T...
Page 202
DIGITAL REF No. Part No. Part Name Remarks Q'ty New R2527 RES,CHIP(1005/5%/10Kohm) CRJ06IJ103T R2528,2529 RES,CHIP(1005/5%/4.7Kohm) CRJ06IJ472T R2530 RES,CHIP(1005/5%/33ohm) CRJ06IJ330T R2531 RES,CHIP(1005/5%/10Kohm) CRJ06IJ103T R2532 RES,CHIP(1005/5%/4.7Kohm) CRJ06IJ472T R2535-2538 RES,CHIP(1608/5%/33ohm) CRJ10DJ330T R2539 RES,CHIP(1005/5%/91ohm) CRJ06IJ910T R2540 RES,CHIP(1005/5%/0ohm) CRJ06IJ0R0T R2541,2542 RES,CHIP(1005/5%/10Kohm) CRJ06IJ103T R2543 RES,CHIP(1005/5%/33ohm) CRJ06IJ330T R2545 RES,CHIP(1005/5%/10Kohm) CRJ06IJ103T...
Page 203
DIGITAL REF No. Part No. Part Name Remarks Q'ty New R3846 RES,CHIP(1005/5%/47Kohm) CRJ06IJ473T R3847,3848 RES,CHIP(1005/5%/0ohm) CRJ06IJ0R0T R3851 RES,CHIP(1005/5%/1Kohm) CRJ06IJ102T R3852 RES,CHIP(1005/5%/10Kohm) CRJ06IJ103T R3853,3854 RES,CHIP(1005/5%/47Kohm) CRJ06IJ473T R3855 RES,CHIP(1608/5%/0ohm) CRJ10DJ0R0T R3856 RES,CHIP(1005/5%/47Kohm) CRJ06IJ473T R3857,3858 RES,CHIP(1005/5%/0ohm) CRJ06IJ0R0T R3861 RES,CHIP(1005/5%/1Kohm) CRJ06IJ102T R3862 RES,CHIP(1005/5%/10Kohm) CRJ06IJ103T R3863,3864 RES,CHIP(1005/5%/47Kohm) CRJ06IJ473T...
Page 204
DIGITAL REF No. Part No. Part Name Remarks Q'ty New R4356 RES,CHIP(1005/5%/10Kohm) CRJ06IJ103T R4357,4358 RES,CHIP(1608/1%/51ohm) CRJ10DF51R0T R4359 RES,CHIP(1005/5%/0ohm) CRJ06IJ0R0T R4367 RES,CHIP(1608/5%/330ohm) CRJ10DJ331T R5001-5003 RES,CHIP(1005/5%/0ohm) CRJ06IJ0R0T R5004 RES,CHIP(1005/5%/100ohm) CRJ06IJ101T R5005 RES,CHIP(1005/5%/0ohm) CRJ06IJ0R0T R5006 RES,CHIP(1005/5%/100ohm) CRJ06IJ101T R5007 RES,CHIP(1005/5%/0ohm) CRJ06IJ0R0T R5008 RES,CHIP(1005/5%/100ohm) CRJ06IJ101T R5009 RES,CHIP(1005/5%/10Kohm) CRJ06IJ103T...
Page 205
DIGITAL REF No. Part No. Part Name Remarks Q'ty New C1165 CAP,CHIP(2012,6.3V/22uF,X5R)_SAMSUNG CCUC0J226KCS C1166 CAP,CHIP(2012,6.3V/10uF,X5R)_SAMSUNG CCUC0J106KCS C1169 CAP,CHIP(2012,50V/0.1uF,X7R)_SAMSUNG CCUC1H104KCS C1171 CAP,CHIP(1005,16V/0.1uF,X7R)_SAMSUNG CCUI1C104KCS C1172 CAP,CHIP(2012,6.3V/10uF,X5R)_SAMSUNG CCUC0J106KCS C1173 CAP,CHIP(1608,10V/1uF,X7R,X7S)_SAMSUNG CCUS1A105KCS C1174 CAP,CHIP(1608,50V/7pF,C0G)_SAMSUNG CCUS1H070DAS C1175 CAP,CHIP(2012,6.3V/22uF,X5R)_SAMSUNG CCUC0J226KCS C1176 CAP,CHIP(2012,6.3V/10uF,X5R)_SAMSUNG CCUC0J106KCS C1179 CAP,CHIP(2012,50V/0.1uF,X7R)_SAMSUNG CCUC1H104KCS C1181 CAP,CHIP(1005,16V/0.1uF,X7R)_SAMSUNG CCUI1C104KCS...
Page 206
DIGITAL REF No. Part No. Part Name Remarks Q'ty New C2046 CAP,CHIP(1005,16V/0.1uF,X7R)_SAMSUNG CCUI1C104KCS C2047,2048 CAP,CHIP(1005,50V/33pF,C0G)_SAMSUNG CCUI1H330JAS C2049 CAP,CHIP(1005,16V/0.1uF,X7R)_SAMSUNG CCUI1C104KCS C2051,2052 CAP,CHIP(1005,16V/0.1uF,X7R)_SAMSUNG CCUI1C104KCS C2201,2202 CAP,CHIP(1005,50V/100pF,C0G)_SAMSUNG CCUI1H101JAS C2203 CAP,CHIP(1005,50V/1000pF,X7R)_SAMSUNG CCUI1H102KCS C2204-2212 CAP,CHIP(1005,16V/0.1uF,X7R)_SAMSUNG CCUI1C104KCS C2217 CAP,CHIP(1005,50V/100pF,C0G)_SAMSUNG CCUI1H101JAS C2501-2503 CAP,CHIP(1005,16V/0.1uF,X7R)_SAMSUNG CCUI1C104KCS C2504,2505 CAP,CHIP(1608,50V/18pF,C0G)_SAMSUNG CCUS1H180JAS C2506-2541 CAP,CHIP(1005,16V/0.1uF,X7R)_SAMSUNG CCUI1C104KCS...
Page 207
DIGITAL REF No. Part No. Part Name Remarks Q'ty New C3576 CAP,CHIP(1005,16V/0.1uF,X7R)_SAMSUNG CCUI1C104KCS C3577 CAP,CHIP(1005,25V/0.01uF,X7R)_SAMSUNG CCUI1E103KCS C3578 CAP,CHIP(1005,16V/0.1uF,X7R)_SAMSUNG CCUI1C104KCS C3579 CAP,CHIP(1005,25V/0.01uF,X7R)_SAMSUNG CCUI1E103KCS C3580 CAP,CHIP(1005,16V/0.1uF,X7R)_SAMSUNG CCUI1C104KCS C3581 CAP,CHIP(1005,25V/0.01uF,X7R)_SAMSUNG CCUI1E103KCS C3582 CAP,CHIP(1005,16V/0.1uF,X7R)_SAMSUNG CCUI1C104KCS C3583 CAP,CHIP(1005,25V/0.01uF,X7R)_SAMSUNG CCUI1E103KCS C3584 CAP,CHIP(1005,16V/0.1uF,X7R)_SAMSUNG CCUI1C104KCS C3585 CAP,CHIP(1005,25V/0.01uF,X7R)_SAMSUNG CCUI1E103KCS C3586 CAP,CHIP(1005,16V/0.1uF,X7R)_SAMSUNG CCUI1C104KCS...
Page 208
DIGITAL REF No. Part No. Part Name Remarks Q'ty New C3716 CAP,CHIP(1005,16V/0.1uF,X7R)_SAMSUNG CCUI1C104KCS C3717 CAP,CHIP(1005,25V/0.01uF,X7R)_SAMSUNG CCUI1E103KCS C3718 CAP,CHIP(1005,16V/0.1uF,X7R)_SAMSUNG CCUI1C104KCS C3719 CAP,CHIP(1005,25V/0.01uF,X7R)_SAMSUNG CCUI1E103KCS C3720 CAP,CHIP(1005,16V/0.1uF,X7R)_SAMSUNG CCUI1C104KCS C3721 CAP,CHIP(1005,25V/0.01uF,X7R)_SAMSUNG CCUI1E103KCS C3722 CAP,CHIP(1005,16V/0.1uF,X7R)_SAMSUNG CCUI1C104KCS C3723 CAP,CHIP(1005,25V/0.01uF,X7R)_SAMSUNG CCUI1E103KCS C3724 CAP,CHIP(1005,16V/0.1uF,X7R)_SAMSUNG CCUI1C104KCS C3725 CAP,CHIP(1005,25V/0.01uF,X7R)_SAMSUNG CCUI1E103KCS C3726 CAP,CHIP(1005,16V/0.1uF,X7R)_SAMSUNG CCUI1C104KCS...
Page 209
DIGITAL REF No. Part No. Part Name Remarks Q'ty New C4097 CAP,CHIP(1005,16V/0.1uF,X7R)_SAMSUNG CCUI1C104KCS C4098 CAP,CHIP(1005,25V/0.01uF,X7R)_SAMSUNG CCUI1E103KCS C4099 CAP,CHIP(1005,16V/0.1uF,X7R)_SAMSUNG CCUI1C104KCS C4100 CAP,CHIP(1005,25V/0.01uF,X7R)_SAMSUNG CCUI1E103KCS C4101 CAP,CHIP(1005,16V/0.1uF,X7R)_SAMSUNG CCUI1C104KCS C4102 CAP,CHIP(1005,25V/0.01uF,X7R)_SAMSUNG CCUI1E103KCS C4103 CAP,CHIP(1005,16V/0.1uF,X7R)_SAMSUNG CCUI1C104KCS C4104 CAP,CHIP(1005,25V/0.01uF,X7R)_SAMSUNG CCUI1E103KCS C4105 CAP,CHIP(1005,16V/0.1uF,X7R)_SAMSUNG CCUI1C104KCS C4106 CAP,CHIP(1005,25V/0.01uF,X7R)_SAMSUNG CCUI1E103KCS C4107 CAP,CHIP(1608,6.3V/4.7uF,X5R)_SAMSUNG CCUS0J475KCS...
Page 210
DIGITAL REF No. Part No. Part Name Remarks Q'ty New C5091 CAP,CHIP(1005,16V/0.1uF,X7R)_SAMSUNG CY920 Model CCUI1C104KCS C5092,5093 CAP,CHIP(1608,10V/1uF,X7R,X7S)_SAMSUNG CY920 Model CCUS1A105KCS C5094 CAP,CHIP(1005,16V/0.1uF,X7R)_SAMSUNG CY920 Model CCUI1C104KCS C5101 CAP,CHIP(1005,16V/0.1uF,X7R)_SAMSUNG CCUI1C104KCS C5111 CAP,CHIP(1005,25V/0.022uF,X7R)_SAMSUNG CCUI1E223KCS OTHER PARTS GROUP BK102,103 BRACKET,PCB CMD1A569-V1 BK501,502 BRACKET,NETWORKA CMD1A900 BN111 WIREASS'Y(4P,2.0MM,120MM,UL1007#24) CWB1C004120LC...
Page 211
CX870CONNECTOR CX870CONNECTOR PCB ASS'Y ※Parts indicated by "nsp"on this table cannot be supplied. ※The parts listed below are only for maintenance. Therefore they might differ from the parts used in the unit in appearances or dimensions. NOTE:The symbols in the column Remarks indicate the following destinations. U : North America model N : Europe model K : China model F : Japan model B : Black model SG : Silver Gold model...
Page 212
943101102530D TRANS,POWER(EI96X65) CLT5V068ZE 2PWIREASS'Y(100MM) CWZPM5003TW91A ┣TW91 2PWIREASS'Y(100MM) CWZPM5003TW91 ! ┗RT01 00MYJ04002640 RECEPTACLE,AC(15A/250V,R-301,B21) CJJ8A006ZW TERMINAL,GROUND CMA1A006 421410006004M BADGE,MARANTZ CGB1A206 943402104840M PANEL AL FRONT (U) CKM1A249QC23 943402104820M PANEL AL FRONT (N1B) CKM1A249PC23 943402104810M PANEL AL FRONT (N1SG) N1SG CKM1A249OC62 412410005014M VOLUMEKNOBASS'Y CGK1A133YA...
Page 214
PACING PACING ※Parts indicated by "nsp"on this table cannot be supplied. ※The parts listed below are only for maintenance. Therefore they might differ from the parts used in the unit in appearances or dimensions. NOTE:The symbols in the column Remarks indicate the following destinations. U : North America model N : Europe model K : China model F : Japan model B : Black model SG : Silver Gold model...