Thank you for purchasing the Clarion TB741P/TB742P/TB743W. * Please read this Owner’s manual & Installation manual in its entirety before proceeding with wire connection and installation. * After reading this manual, be sure to keep it in a handy place (e.g., glove compartment).
I Preset Tuning (total of 12 stations), Manual Tuning and Automatic Tuning Facilities for Speedy Selection of Any Broadcast Station I Very Easy and Functional Operation I Built-in 4-channel Diversity Unit I 2 AV input (RCA/DIN) I 1 AV output (RCA) I RADIO ANT IN/OUT (TB741P, TB742P only) TB741P/TB742P/TB743W...
∗ If the reception is poor, switch to a station with good reception. CHANGES OR MODIFICATIONS TO THIS PRODUCT NOT APPROVED BY THE MANUFACTURER WILL VOID THE WAR- RANTY. TB741P/TB742P/TB743W...
• Press and hold this button for 1 second or longer to switch the display sizes. [PWR] button • Press this button to turn on/off the power. TB741P/TB742P/TB743W [BND] button • Press this button to switch the receiving bands. • Press and hold this button for 1 second or longer to turn on/off the monitor.
TV program or other software media, you will not be able to view the original pictures as was originally intended. Bear this point in mind when selecting the screen mode. TB741P/TB742P/TB743W...
6. REMOTE CONTROL Operating range: 30˚ in all directions Remote control unit [ POWER ] TB741P/TB742P/TB743W Receiver for remote control unit Signal transmitter Inserting the Battery [ BAND/RTN/ADJ ] 1. Turn the remote control unit over, then slide the rear cover in the direction of the arrow.
• Hold down for 1 second for Seek tuning. [PS/AS] button • Preset scan. • Hold down for 1 second for auto store. [1-6] buttons • Selecting the preset channel directly. • Hold down for 1 second to store the current station into preset memory. TB741P/TB742P/TB743W...
3. Press the [PWR] button to turn off the power for the unit. TB741P/TB742P/TB743W Note: Be sure to read this chapter referring to the front diagrams of chapter “1. CONTROL” on page 3 (spread). Standing up the liquid crystal panel 1.
∗ When a button is pressed or during security monitoring, the monitor-off mode is canceled. Car stereo adjustments 1. Set the car stereo’s radio frequency to the modulator frequency. (TB741P/TB742P only) ∗ The factory set for the modulator frequency is 88.1 MHz. (Refer to the section on selecting the FM modulator frequency on page 15.)
Page 12
G Normal mode NORMAL Black bands appear all around the screen. TB741P/TB742P/TB743W Note: • When the wide mode or full wide mode is used to display a normal 4:3 picture which is not a wide picture so that it fills the whole wide TV screen,...
6. To cancel the manual memory mode, press the [MEMO] button again and press the [DISP] button. Note: • The memory contents are returned to the default settings when the battery is replaced or the power supply is otherwise suspended. F.WIDE A.STORE TB741P/TB742P/TB743W...
[ MODULATOR ] [ MODU FREQ ] 2. Press the [w] or [z] button to select the desired adjustment menu. TB741P/TB742P/TB743W Adjusting the brightness and tone of color 1. Display the adjustment menu as described in the section, “Selecting the adjustment menu”.
Page 15
∗ The factory default setting is “ON”. Selecting the FM modulator frequency (TB741P/TB742P only) 1. Display the adjustment menu as described in the section, “Selecting the adjustment menu”. [ MONI...
Page 16
3. Press the [ADJ] button to return to the normal screen mode. ∗ The factory default setting is “HI”. TB741P/TB742P/TB743W Changing the TV reception area (TB741P only) ∗ The factory default setting is “OTHERS”. 1. Display the adjustment menu as described in the section, “Selecting the adjustment menu”.
∗ When the reset button is pressed, frequencies of TV, etc. stored in memory are cleared. When direct rays of the sun fall on the light-receptive part of the remote controller, it may not work. Check the batteries of the remote controller unit. Measure The Reset button TB741P/TB742P/TB743W...
Page 18
There are red, green, and blue points in the display. TB741P/TB742P/TB743W Cause Check that the parking brake is applied. Adjust the brightness properly. The temperature inside the vehicle may be 0˚C or less. Set to an appropriate temperature (25˚C or so) and check it again.
Special screw ... 1 GENERAL CAUTIONS 1. Do not open the case. There are no user serviceable parts inside. If you drop anything into the unit during installation, consult your dealer or an authorized Clarion service center. TB741P TB742P TB743W...
Using other screws can cause damage. (Figure 4) Chassis Chassis Max. 8 mm Figure 4 TB741P/TB742P/TB743W 6. The main unit has mounting screw holes for NISSAN (N marks) and TOYOTA (T marks) vehicles. (Figure 5) Shift stick Damage Figure 5...
Screwdriver Main Unit Outer escutcheon Notes: 1) Some car models require special mounting kits for proper installation. Consult your Clarion dealer for details. 2) Fasten the front stopper securely to prevent the main unit from coming loose. Instrument panel Hole...
Page 24
Note 1: In some cases, the center panel may require some modification (trimming, filling, etc.). TB741P/TB742P/TB743W 2. Secure the mounting brackets to the chassis as shown in Figure 8. Holes are pre-tapped for TOYOTA and NISSAN vehicles;...
Keep the hook plate. You cannot remove the main unit without disengaging the hook plate. Instrument panel Main Unit Figure 9 Figure 10 Fuse holder Figure 11 TB741P/TB742P/TB743W Spring Screw on car Fasten securely to a clean metal plate on the car. Fuse...
Illumination power supply lead Parking brake lead (✻6) (✻8) *1: Connect this to the antenna input terminal on the car stereo. (TB741P/TB742P only) *2: Connect the vehicle’s radio antenna to this. (TB741P/TB742P only) *3: Connect to the power supply terminal which can be turned on and off by the ignition switch.
Page 27
• When the parking brake lead is not connected, the monitor will stay off. Insulating tape Parking brake lamp + lead to battery Connect these three leads. - cord parking brake signal Parking brake lead lead (bright green) Parking brake TB741P/TB742P/TB743W...
SAMPLE SYSTEMS TB741P/TB742P only Radio antenna Clarion products or Car stereo with FM Tuner (sold sepatately) Speakers TB741P/TB742P/TB743W Notes: • For details on the connecting terminals, refer to the section on wire connections (page 26). TB741P/TB742P/TB743W 4-system TV diversity antenna...
Page 29
ZCB-303 TV antenna (diversity) for vehicles * Various conversion adaptors, extension cords, antennas and other parts are available in addition to what is listed above. For details, consult your dealer or your nearest Clarion service outlet. Application No. of systems...
Need help?
Do you have a question about the TB741P and is the answer not in the manual?
Questions and answers