Thank you for purchasing the Clarion TB731P/TB732P/TB733W. * Please read this Owner’s manual & Installation manual in its entirety before proceeding with wire connection and installation. * After reading this manual, be sure to keep it in a handy place (e.g., glove compartment).
I Very Easy and Functional Operation I Built-in 4-channel Diversity Unit I 2 AV input (RCA/DIN) I 1 AV output (RCA) I RADIO ANT IN/OUT (TB731P, TB732P only) 2. PRECAUTIONS CAUTION For your safety, the driver should not watch the TV or operate the controls while driving.
TV program or other software media, you will not be able to view the original pictures as was originally intended. Bear this point in mind when selecting the screen mode. TB731P/TB732P/TB733W...
[ 1-6 ] batteries. • Do not dispose of batteries into fire or water. • Dispose of spent batteries properly. Rear side TB731P/TB732P/TB733W Functions of Remote Control Unit Buttons [POWER] button • Power on/off. [DISP] button • Showing the information on the screen.
∗ There are 3 adjustable positions available on 1. Set the car stereo’s radio frequency to the this panel. modulator frequency. (TB731P/TB732P only) ∗ The factory set for the modulator frequency is 88.1 MHz. (Refer to the section on selecting the FM modulator frequency on page 15.)
NORMAL Wide mode, full wide Black bands appear all around the screen. TB731P/TB732P/TB733W TV Mode Operations For your safety, the driver should not watch the TV or operate the controls while driving. Please note that watching and operating the TV while driving is prohibited by law in some countries.
Page 9
Color COLOR screen mode. MONI ADJ ∗ The factory default setting is “ON”. Selecting the FM modulator frequency (TB731P/TB732P only) 1. Display the adjustment menu as described in the section, “Selecting the adjustment menu”. [ MONI BEEP [ MODULATER ] MODU FREQ 2.
3. Press the [ADJ] button to return to the normal screen mode. ∗ The factory default setting is “HI”. TB731P/TB732P/TB733W 8. TROUBLESHOOTING I If you think that something has gone wrong with your unit, check out the following points before requesting servicing.
CCIR NEW ZEALAND 1 to 11 ch AUSTRALIA UHF: CCIR NEW ZEALAND 21 to 69 ch AUSTRALIA • TB732P VHF: 1 to 12 ch (48.5 to 223 MHz) UHF: 13 to 57 ch (470 to 870 MHz) • TB733W VHF:...
Never use a rough cloth, thinner, benzine, or into the unit during installation, consult your alcohol, etc. For tough dirt, apply a little cold dealer or an authorized Clarion service or warm water to a soft cloth and wipe off center.
Outer escutcheon INSTALLING THE MAIN UNIT Notes: 1) Some car models require special mounting kits for proper installation. Consult your Clarion dealer for details. 2) Fasten the front stopper securely to prevent the main unit from coming loose. 182 mm...
Note 1: In some cases, the center panel may Note 2: If a hook on the installation bracket require some modification (trimming, filling, etc.). TB731P/TB732P/TB733W 1. When the rear of the main unit has been secured with the method shown in Figure 6 unfasten the special screw.
(✻8) *1: Connect this to the antenna input terminal *6: Connect to the ground lead of the parking on the car stereo. (TB731P/TB732P only) brake lamp in the instrument panel. *2: Connect the vehicle’s radio antenna to this. *7: There are four antenna terminals: Main and (TB731P/TB732P only) sub.
* Various conversion adaptors, extension cords, antennas and other parts are available in addition to what is Connected to audio output terminals listed above. For details, consult your dealer or your nearest Clarion service outlet. (RCA pin jacks) (sold separately)
Need help?
Do you have a question about the TB732P and is the answer not in the manual?
Questions and answers