Marantz SR7009/U1B Service Manual page 31

3.5.6 Video system confirmation items
fig. XX: Refer to the block diagram of the fig.XXth.
Confirmation items
Analog Video through (signal) Path
V 0 1 V I D E O
fig.17
V01 * * * . * d B
video convert
V 0 2 C O N V .
(analog or HDMI ⇒ HDMI)
* * * . * d B
fig.18a, fig.18b
V02
HDMI through (signal) Path
V 0 3 H D M I
(Main Zone)
fig.19
V03
* * * . * d B
CEC
V 0 4 C E C
( Control Monitor : HDMI Monitor1 )
* * * . * d B
V04
fig.20
HDMI audio
V 0 5 H - A V R
(audio: AVR)
V05
* * * . * d B
fig.21a, fig.21b, fig21c
HDMI audio
V 0 6 H - T V
(audio: TV)
V06 fig.22a, fig.22b
* * * . * d B
OSD
V 0 7 M E N U
fig.23
* * * . * d B
V07
HDMI (signal) Path
V 0 8 Z 2 H D
(ZONE2)
fig.24
V08 * * * . * d B
FL display
Input Source : CBL / SAT
Video Convert ( IP Scaler ) : OFF, All sources
MAIN ZONE : ON
ZONE2 : ON
Input Source : CBL/SAT
Video Convert ( IP Scaler ) : ON, All sources
IP Scaler : "Analog&HDMI", All sources
Resolution : "Auto", All sources
MAIN ZONE : ON
ZONE2 : OFF
ZONE3 : OFF
Input Source : CBL/SAT
Video Convert ( IP Scaler ) : OFF , All Sources
MAIN ZONE : ON
ZONE2 : OFF
ZONE3 : OFF
Input Source : CBL/SAT
HDMI Control : ON
Control Monitor : Monitor1(HDMI Monitor Out 1)
MAIN ZONE : ON
ZONE2 : OFF
ZONE3 : OFF
Input Source : CBL/SAT
HDMI Control : OFF
HDMI Audio : AVR (audio output from AVR)
HDMI Audio : TV (audio output from TV)
Input Source : CBL/SAT
Video Convert(IP Scaler) : ON, All sources
IP Scaler : "Analog&HDMI", All sources
Resolution : "AUTO", All sources
Setup Menu ON
MAIN ZONE : ON
ZONE2 : OFF
ZONE3 : OFF
Input Source : CBL/SAT
ZONE2 Source : Source
MAIN ZONE : ON
ZONE2 : ON
ZONE3 : OFF
Settings
·Component input ⇒ Component output
( b As the input source, you can switch from CBL/SAT to other ones.)
·CVBS input ⇒ IP Scaler Through ⇒ HDMI output
·Component input ⇒ IP Scaler ⇒ HDMI output
·HDMI input ⇒ IP Scaler ⇒ HDMI output
·ETHERNET input ⇒ IP Scaler ⇒ HDMI output
( b As the input source, you can switch from CBL/SAT to other ones.)
·HDMI input ( MAIN Function ) ⇒ HDMI output (MAIN)
( b As the input source, you can switch from CBL/SAT to other ones.)
·When the power supply of a TV is put in the standby mode, make sure that the power supply
of this unit is also put in the standby mode.
( b As the input source, you can switch from CBL/SAT to other ones.)
·To check ARC path, switch the input source to "TV AUDIO".
·HDMI input(PCM , DolbyDigital , DTS) ⇒ Speaker output
·HDMI input(HD audio) ⇒ Speaker output
( b As the input source, you can switch from CBL/SAT to other ones.)
·HDMI input(PCM , DolbyDigital , DTS) ⇒ HDMI output (audio output from connected TV)
( b As the input source, you can switch from CBL/SAT to other ones.)
·OSD display ⇒ HDMI output
( b As the input source, you can switch from CBL/SAT to other ones.)
·HDMI input (ZONE2 Function) ⇒ HDMI output (ZONE2)
( b As the input source, you can switch from CBL/SAT to other ones.)
31
Contents of confirmation