ESCO Technologies ETS-LINDGREN AMS-8923 Quick Start Manual

Safety Information
Laser Danger: Denotes a laser (IEC Class 3B) is part of the operating system of the device. Laser power
range is 5-500 mW.
Visible laser radiation: Avoid exposure to beam. Do not stare into beam or view directly with optical instruments.
BEFORE POWER IS APPLIED TO THIS INSTRUMENT, GROUND IT PROPERLY through the protective conductor
of the AC power cable to a power source provided with protective earth contact. Any interruption of the protective
(grounding) conductor, inside or outside the instrument, or disconnection of the protective earth terminal
could result in personal injury.
HIGH VOLTAGE: Indicates presence of hazardous voltage. Unsafe practice could result in severe personal injury
or death.
CONTACT ETS-LINDGREN PRIOR TO SERVICING. Servicing (or modifying) the unit by yourself may void your
warranty if you attempt to service the unit by yourself, disconnect all electrical power before starting. There are
WARRANTY
voltages at many points in the instrument that could, if contacted, cause personal injury. Only trained service
personnel should perform adjustments and/or service procedures upon this instrument. Capacitors inside this
instrument may still be CHARGED even when instrument is disconnected from its power source.
F r o a d d t i o i n a s l f a t e i y f n r o m t a o i , n s e e h t e
Product Information Bulletin
S e e h t e E T S L - n i d g e r n
Product Information Bulletin
Warranty information
Safety, regulatory, and other product marking information
Steps to receive your shipment
Steps to return a component for service
ETS-Lindgren calibration service
ETS-Lindgren contact information
Warranty Information
F r o w r a a r t n i y f n r o m t a o i , n s e e h t e Product Information Bulletin.
USA Headquarters
1301 Arrow Point Drive
Cedar Park, TX 78613
Phone: +1.512.531.6400
Please see ets-lindgren.com for a list of all ETS-Lindgren offices.
© Copyright 2007-2017 by ETS-Lindgren Inc. All Rights Reserved. No part of this document may be copied
by any means without written permission from ETS-Lindgren Inc.
The ETS-Lindgren logo is a registered trademark of ETS-Lindgren Inc.
1, Custom Design - August, 2007 B, Revised Release - April, 2017
399800, Rev B
Revision / Date:
A, Initial Release - May, 2010
Product Information Bulletin n i c u l d e d i w h t y o r u s h p i m
n i c u l d e d i w h t y o r u s h p i m e n f t r o h t e o f o l l w n i : g
ets-lindgren.com
These components are required to connect the AMS-8923 Measurement System:
•
Control Box (part# 114760)
LASER
•
AMS-8923
e n . t
•
10-Meter Fiber Optic Cable
(part# 705344-10)
Additional cables
(as required by configuration)
•
TM
EMCenter
Note: ETS-Lindgren may substitute a similar part with the same functionality for another part.
AMS–8923 Controller Box Part #114760
WA R N I N G
H I G H VO LTA G E
100/240 VAC
50/60 Hz
100 VA M AX
LASER
DISPLAY RF PORTS
SWITCH
DEDICATED PATHS SWITCHED
PATH
THETA PHI
TRIGGER
OUTPUT
Left Side
(part# 114700) installed in finished chamber
Modular RF Platform
EMCenter
™
Power On
Interlock
Laser On
Standby
AMS-8923 Connection Diagram
PHI THETA
+105 +105
+90 +90
+75 +75
+60 +60
+45 +45
+30 +30
Right +15 +15
0 0
Top PHI THETA
-15 -15
-30 -30
-45 -45
-60 -60
-75 -75
-90 -90
-105 -105
-120 -120
Right
PHI THETA
-135 -135
Bottom -150 -150
-165 -165
+165 +165
+150 +150
+135 +135
+120 +120
Right Side
•
Interconnect Kit (part# 115018)
4-Conductor Cable (part# 660046)
8-Conductor Cable (part# 660047)
Fiber Optic Cable (part# 705344-10)
BNC Cable
(part# 106043-10m)
Laser Cable Laser Control
(part# 665080) (part# 115017)
ALI GNM E NT LAS E RS
OF F
ON
Sensor Position Display
(part# 115014)
•
Test Instrumentation
(required units provided by customer)
T EST INST RUM ENT
ets-lindgren.com