Subscribe to Our Youtube Channel
Related Manuals for ESCO Technologies ETS LINDGREN 2302-001
Summary of Contents for ESCO Technologies ETS LINDGREN 2302-001
- Page 1 2302 Positioners User Manual User Manual PN: 1723280 July, 2021 Rev A ets-lindgren.com...
- Page 2 ETS-Lindgren Inc. reserves the right to make changes to any products herein to improve functioning or design. Although the information in this document has been carefully reviewed and is believed to be reliable, ETS-Lindgren does not assume any liability arising out of the application or use of any product or circuit described herein;...
-
Page 3: Table Of Contents
TABLE OF CONTENTS NOTES, CAUTIONS AND WARNINGS SAFETY INFORMATION INTRODUCTION Standard Configuration ........7 2302 Positioner Assembly . - Page 4 DRAWINGS 2302-001 ..........14 2302-002 .
-
Page 5: Notes, Cautions And Warnings
NOTES, CAUTIONS AND WARNINGS Note: Denotes helpful information intended to provide tips for better use of the product. CAUTION: Denotes a hazard. Failure to follow instructions could result in minor personal injury and/or property damage. Included text gives proper procedures. WARNING: Denotes a hazard. -
Page 6: Safety Information
SAFETY INFORMATION Refer to Manual: When product is marked with this symbol, see the instruction manual for additional information. Manuals are available for download at ETS-Lindgren.com, or contact ETS-Lindgren Customer Service. High Voltage: Indicates presence of hazardous voltage. Unsafe practice could result in severe personal injury or death. -
Page 7: Introduction
INTRODUCTION The ETS-Lindgren’s 2302 Type Positioners (Columns) are designed to perform automated 3-dimensional pattern measurements. The positioner is utomated 3-dimensional pattern measurements. The positioner is Note: a vertical support column that will accommodate its respective antenna. a vertical support column that will accommodate its respective antenna. See the ETS-Lindgren Product Information There are three types of 2302 positioners available. -
Page 8: Ets-Lindgren Product Information Bulletin
2302-001 • 66.0" Centerline Column • 1722996 Horn 2302-002 • 60.0" Centerline Column • 1722996 Horn 2302-003 • 114.0" Centerline Column • 3164-08 Antenna Note: See the ETS-Lindgren ETS-Lindgren Product Information Bulletin Product Information Bulletin for safety, regu- See the ETS-Lindgren Product Information Bulletin included with your latory, and other product shipment for the following: marking information. -
Page 9: Maintenance
MAINTENANCE Before installing any components, follow the safety information in the ETS- Before assembling, Lindgren Product Information Bulletin included with your shipment. If you have installing, or connecting any questions concerning maintenance, contact ETS-Lindgren Customer Service. any components, follow the safety information in the ETS-Lindgren Maintenance Recommendations Product Information... -
Page 10: Specifications
SPECIFICATIONS Electrical Requirements for 2302s Single Phase, 200-240VAC and 10A max. 2302-001 Physical Specifications Centerline Height: 167.64 cm (66.0 in) Width: 40.64 cm (16.0 in) Depth: 40.64 cm (16.0 in) 2302-002 Physical Specifications Centerline Height: 152.4 cm (60.0 in) Width: 40.64 cm (16.0 in) Depth: 40.64 cm (16.0 in) -
Page 11: Installation
INSTALLATION Pre-Installation Tasks Before assembling, installing, or connecting Pre-planning is essential for successful installation. Discuss requirements any components, follow with your sales representative and request dimensional drawings prior to the safety information construction of your site. in the ETS-Lindgren Product Information Positioner Installation Bulletin included with your shipment. -
Page 12: Leveling The Fixture
Leveling the Fixture Once secured to the chamber floor, use the three levels to level the fixture. Denotes a laser (class 2) is part of the operating system of the device. Levels WARRANTY Only qualified 2. Place the laser fixture personnel should (001 exempt) on the operate (or service) -
Page 13: Operation
OPERATION WARRANTY Pre-Operational Tasks • Verify that the power line is properly connected to the column assembly Only qualified personnel should • Verify fixture(s) are secured to the column assembly operate (or service) this equipment. Laser Fixture (002 & 003) If you have any questions concerning To activate laser on column, first locate the on/off button and press to switch... - Page 14 DRAWINGS 2302-001...
- Page 15 2302-002...
- Page 16 2302-003...
Need help?
Do you have a question about the ETS LINDGREN 2302-001 and is the answer not in the manual?
Questions and answers