Advertisement
Quick-Start Guide
Selecting a Model Memory
Your transmitter can store up to 15 models in its memory,
where all of the settings are stored independently for each
model. This enables you to use one transmitter with up to
15 different vehicles. To change the model memory:
1. Turn ON the transmitter.
2. Press the Roller Button (1) once to access the
programming list. The letters MOD will appear on the
screen indicating that you are in the Model memory
menu.
3. Press the Roller Button once more to enter the MOD
menu that contains the 15 model memories.
4. The screen will display the current / active model
memory, i.e. MOD 01.
5. Rotate the Roller Button to select the model memory
you require.
6. Confirm the selection and return to the home screen
by pressing the Back Button (1) twice. The new / active
model memory will now be displayed below the voltage.
Basic Guide to Programming
Transmitter programming is carried out using the Roller
Button (5) and the Back Button (6).
1. From the home screen press the Roller Button (5) once
to access the programming list. The letters MOD will
appear on the screen indicating that you are in the
Model memory menu.
2. Rotating the Roller Button forwards, one stop at a time,
will display the various programming options which will
appear in the following order:
• MOD (Model Memory)
• TRM (Trim adjustment)
• D/R (Rate adjustment)
• EPA (End Point Adjustment)
Feature List
• 15 model memory with Pair Safe
• 2.4GHz operation avoids conflicts with other users
• Easily pairs with vehicles pre-equipped with IKONNIK
Xenon technology
• Backlit LCD
• Roller button interface
• Ergonomic trigger and grip angle
• Drop-down wheel with adjustable position
• Left- and right-hand compatible operation
• Adjustable wheel tension
• Proportional steering and throttle control
• Digital steering trim
• Digital throttle trim
• End-Point Adjustment (EPA)
• Steering Dual Rate (D/R)
• Servo reversing
• Exponential
• ABS braking
• Rock crawler steering mix / modes
www.ikonnik-rc.com
• EXP (Exponential)
• REV (Servo reverse)
• ABS (ABS braking)
• MIX (Rock crawler steering mix / modes)
• EPA-TY
• F/S (Fail-safe)
• RST (Reset)
3. To select a particular programming option and make
adjustments press the Roller Button once more.
4. Having selected the option you wish to adjust use the
roller button to select (press) and adjust (roll) to suit
your requirements.
By way of example, here's how you would reverse the
direction of the Channel 3 servo.
1. Turn ON the transmitter.
2. Press the Roller Button (5) once to access the
programming list. The letters MOD will appear on the
screen.
3. Use the Roller Button to scroll forward through the
programming options until you reach REV.
4. Press the Roller Button once more to enter the REV
menu. ST (steering) will be displayed indicating that
this is where you can reverse the steering servo.
5. Use the Roller Button to scroll forward to TH (throttle)
and finally 3CH (Channel 3).
6. Press the Roller Button to display the current servo
condition – NOR-3C indicates a normal servo direction
whilst REV-3C indicates a reversed servo direction.
7. Use the Roller to choose the option you require.
8. Return to the home screen by pressing the Back
Button three times.
FOR A DETAILED DESCRIPTION OF HOW TO PROGRAM THE
OTHER MENU OPTIONS REFER TO THE FULL ONLINE MANUAL
• Fail-safe
• Proportional 3rd channel knob
• 4th channel toggle
• Beginner mode (50% throttle)
• Feature lock
• Factory reset (each model and full memory)
• Inactivity warning
• Battery low voltage warning
• Folding antenna for storage
• Uses 4 AA batteries and compatible with NiMH packs
• Micro all-weather Xenon receiver
General Care
1. Always use clean, dry cloth or soft bristle brush to
clean your equipment.
2. Never use chemical cleansers, as these could damage
the sensitive electronics and plastics.
Advertisement
