Table of Contents
Advertisement
Restoring All the Settings to as They were at the
Time of Purchase (Resetting the Microprocessor)
Perform this procedure if the display is abnormal or if operations cannot be performed.
When the microprocessor is reset, all the settings are reset to their default values.
1
Turn off the power using
on the main unit.
2
Press
while simultaneously pressing
3
Once the display starts flashing at intervals of about 1 second, release the two
buttons.
If in step 3 the display does not flash at intervals of about 1 second, start over from step 1.
Specifications
n
Audio section
• Power amplifier
Rated output:
Front (A, B):
105 W+105 W
135 W+135 W
Center:
105 W
135 W
Surround:
105 W+105 W
135 W+135 W
Surround Back:
105 W+105 W
135 W+135 W
Output connectors:
Front:
Center, Surround, Surround Back / Amp Assign:
• Analog
Input sensitivity / Input impedance:
200 mV / 47 kΩ/kohms
10 Hz ~ 100 kHz — +1, –3 dB (DIRECT mode)
Frequency response:
S/N:
100 dB (IHF-A weighted, DIRECT mode)
and
on the main unit.
(8 Ω/ohms, 20 Hz ~ 20 kHz with 0.08 % T.H.D.)
(6 Ω/ohms, 1 kHz with 0.7 % T.H.D.)
(8 Ω/ohms, 20 Hz ~ 20 kHz with 0.08 % T.H.D.)
(6 Ω/ohms, 1 kHz with 0.7 % T.H.D.)
(8 Ω/ohms, 20 Hz ~ 20 kHz with 0.08 % T.H.D.)
(6 Ω/ohms, 1 kHz with 0.7 % T.H.D.)
(8 Ω/ohms, 20 Hz ~ 20 kHz with 0.08 % T.H.D.)
(6 Ω/ohms, 1 kHz with 0.7 % T.H.D.)
A or B
6～16 Ω/ohms
A + B
12～16 Ω/ohms
6～16 Ω/ohms
n
Video section
• Standard video connectors
1 Vp-p, 75 Ω/ohms
Input / output level and impedance:
Frequency response:
5 Hz ~ 10 MHz — +1, –3 dB
• S-Video connectors
Input / output level and impedance:
Y (brightness) signal — 1 Vp-p, 75 Ω/ohms
C (color) signal — 0.286 Vp-p, 75 Ω/ohms
Frequency response:
5 Hz ~ 10 MHz — +1, –3 dB (when video convert set to "OFF")
• Color component video connector
Y (brightness) signal — 1 Vp-p, 75 Ω/ohms
Input / output level and impedance:
P
/ C
B
B
P
/ C
R
R
Frequency response:
5 Hz ~ 60 MHz — +0, –3 dB (when video convert set to "OFF")
n
Tuner section
(note: µV at 75 Ω/ohms, 0 dBf = 1 x 10
Receiving Range:
87.5 MHz ~ 107.9 MHz
Usable Sensitivity:
1.0 µV (11.2 dBf)
50 dB Quieting Sensitivity:
1.6 µV (15.3 dBf)
23 µV (38.5 dBf)
77 dB
S/N (IHF-A):
72 dB
Total harmonic Distortion (at 1 kHz):
MONO
STEREO 0.3 %
n
General
Power supply:
AC 120 V, 60 Hz
Power consumption:
6.0 A
0.3 W (Standby)
Maximum external dimensions:
434 (W) x 171 (H) x 377 (D) mm (17-3/32" x 6-47/64" x 14-27/32")
11.3 kg (24 lbs 14.6 oz)
Weight:
n
Main Remote control unit (RC-1117)
Batteries:
R6/AA Type (two batteries)
Maximum external dimensions:
52 (W) x 243 (H) x 21 (D) mm (2-3/64" x 9-9/16" x 53/64")
184 g (Approx 6.5 oz) (including batteries)
Weight:
n
Sub Remote control unit (RC-1119)
Batteries:
R03/AAA Type (two batteries)
50 (W) x 211 (H) x 22 (D) mm (1-31/32" x 8-5/16" x 55/64")
Maximum external dimensions:
Weight:
110 g (Approx 3.9 oz) (including batteries)
z For purposes of improvement, specifications and design are subject to change without notice.
signal — 0.7 Vp-p, 75 Ω/ohms
signal — 0.7 Vp-p, 75 Ω/ohms
[FM]
[AM]
W)
-15
520 kHz ~ 1710 kHz
18 µV
0.15 %
ENGLISH
0
Advertisement
Table of Contents
