M-system R3-NL1 Instruction Manual page 7

GetValue [x] FUNCTIONAL BLOCKS
NETWORK TYPE
VARIABLE {Range}
{Default}
nvoVal SNVT_lev_percent
{-163.85 through 163.830}
{0.0}
SNVT_state
{0 OFF (input open)
1 ON (input shorted)]
SNVT_temp
{-274.0 through 3002.7}
CONFIGURATION TYPE
PROPERTY {Range}
{Default}
cpNvoType SCPTnvType
{SNVT_lev_percent
SNVT_state
SNVT_temp}
{SNVT_lev_percent}
cpNvoMaxRnge Identical to nvoVal
{ (Identical to nvoVal) }
{100.0}
cpNvoMinRnge Identical to nvoVal
{ (Identical to nvoVal) }
{0.0}
cpSendDelta Identical to nvoVal
{ (Identical to nvoVal) }
{0.0}
SetValue [x] FUNCTIONAL BLOCKS
NETWORK TYPE
VARIABLE {Range}
{Default}
nviVal SNVT_lev_percent
{-163.85 through 163.830}
{0}
SNVT_state
{0 OFF (output open)
1 ON (output shorted)]
CONFIGURATION TYPE
PROPERTY {Range}
{Default}
cpNviType SCPTnvType
{SNVT_lev_percent
SNVT_state}
{SNVT_lev_percent}
cpNviMaxRnge Identical to nviVal
{ (Identical to nviVal) }
{100.0}
cpNviMinRnge Identical to nviVal
{ (Identical to nviVal) }
{0.0}
EXPLANATIONS
• Data acquired from assigned channels.
• Set SNVT_lev_percent for the input types other than
discrete or temperature. Change the network variable type
according to the input type if necessary.
• ConfigurationProperty value must be re-read after the
network variable type is changed. Use "ResyncCP" on the
LonMaker.
• For descrete inputs, change the network variable type to
SNVT_state using integration tools such as LonMaker.
Bit 0 through bit 15 of nvoVal are applied for ch. 1 through
ch. 16.
• For temperature inputs, change the network variable type to
SNVT_temp using integration tools such as LonMaker.
EXPLANATIONS
nvoVal type
(Use integration tools such as LonMaker to change types.)
nvoVal value at 100% input
Invalid when nvoVal type is either SNVT_state or SNVT_temp.
nvoVal value at 0% input
Invalid when nvoVal type is either SNVT_state or SNVT_temp.
Network variables are sent out when its deviation exceeds the
set value.
Invalid when nvoVal type is SNVT_state.
EXPLANATIONS
• Outputs data set to assigned channels.
• Set SNVT_lev_percent for the input types other than
discrete. Change the network variable type according to the
output type if necessary.
• ConfigurationProperty value must be re-read after the
network variable type is changed. Use "ResyncCP" on the
LonMaker.
• For descrete outputs, change the network variable type to
SNVT_state using integration tools such as LonMaker.
Bit 0 through bit 15 of nviVal are applied for ch. 1 through
ch. 16.
EXPLANATIONS
nviVal type
(Use integration tools such as LonMaker to change types.)
nviVal value at 100% output
Invalid when nviVal type is SNVT_state.
nviVal value at 0% output
Invalid when nviVal type is SNVT_state.
R3-NL1
P. 7 / 8 EM-8427 Rev.5