H3C S9500 Series Installation Manual
Routing switches
Hide thumbs
Also See for S9500 Series:
- Command manual (1842 pages) ,
- Operation manual (1504 pages) ,
- Operating manual (76 pages)
Table of Contents
Advertisement
Quick Links
Installation Manual
H3C S9500 Series Routing Switches
Chapter 3 Installing the Switch .......................................................................... 3-1
3.1 Installation Flow ....................................................................................... 3-1
3.2 Confirming Installation Preparation ........................................................... 3-1
3.3 Mounting the Switch in a Rack .................................................................. 3-2
3.3.1 Preparations ................................................................................... 3-2
3.3.3 Mounting the Switch ........................................................................ 3-3
3.3.4 Verifying the Installation .................................................................. 3-3
3.4 Installing the Switch on a Workbench ........................................................ 3-4
3.4.1 Preparations ................................................................................... 3-4
3.4.2 Procedure ....................................................................................... 3-4
3.5 Connecting the PGND Wire ...................................................................... 3-4
3.5.1 In a common grounding environment ............................................... 3-5
3.5.2 In other Grounding Environments .................................................... 3-5
3.6 Installing a PSU ....................................................................................... 3-9
3.6.1 Installation Preparation ................................................................... 3-9
3.6.2 Installation Procedure ..................................................................... 3-9
3.6.3 Connecting Power Cable(s) ............................................................ 3-11
3.7 Installing a Board .................................................................................... 3-15
3.7.1 Installation Preparations ................................................................ 3-15
3.7.2 Installation Procedure .................................................................... 3-16
3.8 Installing PoE Power Supply .................................................................... 3-16
3.8.1 Installation Procedure .................................................................... 3-17
3.8.2 Installing the PoE Power Entry Module ........................................... 3-17
3.8.3 Connecting PoE Power Cables ....................................................... 3-18
3.9 Connecting Interface Cables.................................................................... 3-20
3.9.1 Cable Routing Recommendations ................................................... 3-20
3.9.2 Connecting Console Cable ............................................................. 3-21
3.9.3 Connecting the AUX Cable ............................................................. 3-23
3.9.4 Connecting Network Cables ........................................................... 3-23
3.9.5 Connecting Fiber ........................................................................... 3-23
3.10 Verifying the Installation ........................................................................ 3-27
Table of Contents
i
Table of Contents
Advertisement
Table of Contents
Related Manuals for H3C S9500 Series
Summary of Contents for H3C S9500 Series
-
Page 1: Table Of Contents
Installation Manual H3C S9500 Series Routing Switches Table of Contents Table of Contents Chapter 3 Installing the Switch ................3-1 3.1 Installation Flow ..................3-1 3.2 Confirming Installation Preparation ............3-1 3.3 Mounting the Switch in a Rack ..............3-2 3.3.1 Preparations ................... -
Page 2: Chapter 3 Installing The Switch
H3C S9500 Series Routing Switches Chapter 3 Installing the Switch Chapter 3 Installing the Switch The S9500 series are designed for indoor applications. Warning: Do not touch any exposed wires, terminals or any parts labelled with a high-voltage hazard warning to avoid bodily injury. -
Page 3: Mounting The Switch In A Rack
3.3.2 Installing the Cable Management Bracket and Rack-Mounting Ears For your convenience, a cable management bracket is shipped with the S9500 series. Take the following steps to install the cable management bracket. Facing the LPU slots of the switch, insert the shipped cable... -
Page 4: Mounting The Switch
Installation Manual H3C S9500 Series Routing Switches Chapter 3 Installing the Switch 3.3.3 Mounting the Switch Note: Make sure that supports have been installed in corresponding positions and the supports can bear the switch weight. Two people are required to lift the switch. Put the switch on the supports and slide it into the cabinet until the rack-mounting ears touch against the front square-holed columns. -
Page 5: Installing The Switch On A Workbench
Installation Manual H3C S9500 Series Routing Switches Chapter 3 Installing the Switch Result Item Remarks The rack-mounting ears are well fixed on the switch. The installation position is right. The rack-mounting ears are well fixed on the rack 3.4 Installing the Switch on a Workbench When no 19-inch cabinet is available, you can place the switch on a clean and stable workbench. -
Page 6: In A Common Grounding Environment
Installation Manual H3C S9500 Series Routing Switches Chapter 3 Installing the Switch 3.5.1 In a common grounding environment Follow these steps to connect the PGND wire in a common grounding environment: Remove the screw from the grounding hole in the switch chassis. - Page 7 Installation Manual H3C S9500 Series Routing Switches Chapter 3 Installing the Switch Note: Rather than specifying the switch model or showing the actual location of the switch power input or grounding screw, the following figures are primarily intended for illustrating the switch grounding, either via grounding screw or power input, in specific grounding environments.
- Page 8 Installation Manual H3C S9500 Series Routing Switches Chapter 3 Installing the Switch If there is no ground bar but earth nearby and the grounding body is allowed to be buried, you can simply hammer an angle iron or steel pipe no shorter than 0.5 m into the earth.
- Page 9 Installation Manual H3C S9500 Series Routing Switches Chapter 3 Installing the Switch Caution: Make sure that the PE wire of the AC power supply has been well grounded at the side of the power distribution room or AC power supply transformer.
-
Page 10: Installing A Psu
Installation Manual H3C S9500 Series Routing Switches Chapter 3 Installing the Switch (12) (12) (11) (11) (10) (10) (1) Front panel of the (2) DC power input (3) NEG terminal switch (4) RTN terminal (5) PDF (6) -48V strip (7) RTN strip... - Page 11 Installation Manual H3C S9500 Series Routing Switches Chapter 3 Installing the Switch Clutch the air filter cover by the upper and lower edges with your index finger and the thumb, and gently remove the air filter cover from a PSU.
-
Page 12: Connecting Power Cable(S)
Installation Manual H3C S9500 Series Routing Switches Chapter 3 Installing the Switch Table 3-2 Procedure of installing NEPS3500-A Step Sub-step 1) Hold the handle on the enclosure with one hand and the bottom with the other hand, and gently slide the Install the enclosure along the guide rails into the switch. - Page 13 Installation Manual H3C S9500 Series Routing Switches Chapter 3 Installing the Switch Insert the other end of the power cord into an external power socket. (1) Connector-retention clamp (2) Input LED (3) Output LED (4) Fail LED (5) Power switch...
- Page 14 Installation Manual H3C S9500 Series Routing Switches Chapter 3 Installing the Switch Install the clamp to the socket of the PSU until it grips the plug. Insert the other end of the power cord into an external power socket. (1) Power switch...
- Page 15 Installation Manual H3C S9500 Series Routing Switches Chapter 3 Installing the Switch Connect the other end to the NEG (–) terminal of the source power supply. Connect one end of the cable with GND OT terminals (black) to the RTN (+) terminal on the PSU and fasten the corresponding fixing screw.
-
Page 16: Installing A Board
Installation Manual H3C S9500 Series Routing Switches Chapter 3 Installing the Switch (1) Terminal block (2) Input LED (3) Output LED (4) Fail LED (5) Power switch Figure 3-15 NEPS2000-D appearance Note: NEPS3500-D is similar to NEPS2000-D in appearance, as shown in Figure 3-15. -
Page 17: Installation Procedure
Chapter 3 Installing the Switch Note: Put the removed blank filler panel away for future use. The LPUs of the S9500 series are hot-swappable. 3.7.2 Installation Procedure Follow the procedure below to install an LPU: Turn the ejector levers on the LPU outward simultaneously with both... -
Page 18: Installation Procedure
Installation Manual H3C S9500 Series Routing Switches Chapter 3 Installing the Switch 3.8.1 Installation Procedure Wear the ESD-preventive wrist strap, making sure that it is properly grounded. Remove blank filler panels in the power supply area if applicable. 3.8.2 Installing the PoE Power Entry Module The PoE power entry module is hot-swappable. -
Page 19: Connecting Poe Power Cables
3.8.3 Connecting PoE Power Cables Note: This section only focuses on the cable connection between the external PoE power supply and the S9500 series switch. For the installation of the external PoE power supply, see the manual accompanying the power supply. - Page 20 Installation Manual H3C S9500 Series Routing Switches Chapter 3 Installing the Switch (1) Chassis grounding screw Figure 3-19 Ground the PoE chassis II. Connecting PoE power cables Loosen the mounting screws on the PoE power entry module with a Phillips screwdriver.
-
Page 21: Connecting Interface Cables
Installation Manual H3C S9500 Series Routing Switches Chapter 3 Installing the Switch (1) NEG(–) terminal of DC output (2) RTN(+) terminal of DC output (3) AC input switch (4) AC input socket Figure 3-20 Input/output of external PoE power supply 3.9 Connecting Interface Cables... -
Page 22: Connecting Console Cable
Installation Manual H3C S9500 Series Routing Switches Chapter 3 Installing the Switch Caution: Do not bind cables at the air exhaust vents of the switch to prevent premature cable aging. Fix cables as near the device as possible. The cables between the fixing point and device interfaces must be bound loosely. - Page 23 Installation Manual H3C S9500 Series Routing Switches Chapter 3 Installing the Switch RJ-45 Signal DB-9 Signal II. Connecting the console cable Take the following steps to connect the console cable, when configuring the switch on the terminal. Plug the DB-9 female connector of the console cable into the serial port of the PC/terminal where the switch is to be configured.
-
Page 24: Connecting The Aux Cable
H3C S9500 Series Routing Switches Chapter 3 Installing the Switch 3.9.3 Connecting the AUX Cable You need an AUX cable when configuring the S9500 series with the remote modem dial-up approach. I. Introduction The AUX cable is an 8-core shielded cable. At one end of the cable is an RS-232-compliant RJ-45 connector that can be plugged into the AUX port of the switch. - Page 25 Installation Manual H3C S9500 Series Routing Switches Chapter 3 Installing the Switch Note: The installation method described below is based on an N68 cabinet. The installation procedure is only for your reference if you use a non-N68 cabinet. A fiber management tray (FMT) is installed in a cabinet for winding redundant fibers between the S9500 and other devices.
- Page 26 Installation Manual H3C S9500 Series Routing Switches Chapter 3 Installing the Switch II. Introduction to fiber connector Note: When selecting a fiber network facility, make sure that the type of the connector and the fiber match the adopted optical port.
- Page 27 Crush load (N/100 Period of force Tensile load (N) Short period Long term IV. Connection procedure Connect one end of the fiber to the SFP module of the S9500 series. Connect the other end of the fiber to the peer device. 3-26...
-
Page 28: Verifying The Installation
Installation Manual H3C S9500 Series Routing Switches Chapter 3 Installing the Switch 3.10 Verifying the Installation Warning: Make sure that you have turned off the power before checking the installation in case of bodily injury and device damage. After installing the switch, verify the installation against the following list.
Need help?
Do you have a question about the S9500 Series and is the answer not in the manual?
Questions and answers