1. Manuals
  2. Brands
  3. Ryobi Manuals
  4. Lawn Mower
  5. R36XSCF10
  6. Manual

Ryobi R36XSCF10 Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
FRONT PAGE
R36XSCF10

Advertisement

Table of Contents
loading

Related Manuals for Ryobi R36XSCF10

Summary of Contents for Ryobi R36XSCF10

  • Page 1 FRONT PAGE R36XSCF10...

  • Page 2: Intended Use

    the product is to be used and remove all rocks, sticks, IMPORTANT! metal, wire, bones, toys, or other foreign objects. It is essential that you read the instructions in this manual Remember, string or wire may entangle with the cutting before assembling, operating, and maintaining the means.

  • Page 3: Transportation And Storage

    ■ Never use the product with defective guards or shields, TRANSPORTING LITHIUM BATTERIES or without safety devices, for example, deflectors and Transport the battery in accordance with local and national catchers, in place. provisions and regulations. ■ Do not tilt the product when turning on the motor, except Follow all special requirements on packaging and labelling if the product has to be tilted for starting.

  • Page 4: Symbols On The Product

    SYMBOLS ON THE PRODUCT Safety alert Read the instructions carefully before starting the product. Working width: 35 cm Wear eye protection. Wear ear protection. Regulatory Compliance Mark (RCM). This product meets applicable regulatory requirements. Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist.
  • Page 5 R36XSCF10 Start button Handle grips On/off lever Motor control cable Upper handle Middle handle Handle knob Motor control cable retainer Rear door Catcher Catcher frame Lower handle Depth adjustment lever Battery door Motor housing Wheel Isolator key Handle lock Operator’s manual...
  • Page 6 Wear full eye protection, ear protection, Attach the lower handle to the product. Install a handle lock on each side of non-slip heavy-duty gloves, substantial the lower handle. Turn the handle locks footwear, and long trousers at all times clockwise to tighten. while operating the product.
  • Page 7 Attach the middle handle to the lower Attach the upper handle to the middle Install a screw, washer, and handle handle. Install a screw, washer, and handle. knob on each side. Turn the handle handle knob on each side. Turn the knobs clockwise to tighten.
  • Page 8 Operating the Emptying the p.14 product catcher Adjusting the Replacing the Cleaning and p.11 p.11 p.15 working depth scarifier blade storing the product...

  • Page 9: Operating The Product

    OPERATING THE PRODUCT WARNING: Use the product in areas without any obstructions. Avoid holes, ruts, bumps, rocks, property stakes, or other hidden objects. WARNING: The product can be used on a horizontal slope inclined at a maximum of 15°. Do not operate the product on inclines greater than 15°.
  • Page 10 2. Align the catcher to the rear side of the product. NOTE: The catcher has a hook on each side that fits into the grooves behind the product. 3. Hook the catcher into the grooves. 4. Open the battery door. 5.

  • Page 11: Adjusting The Working Depth

    ADJUSTING THE WORKING DEPTH 1. Release the on/off lever to stop the product. 2. Move the depth adjustment lever to the different settings to set the preferred working depth. NOTE: The 1 setting is the default working depth of the product. The following settings increase the depth.
  • Page 12 3. Remove the isolator key. Remove the battery pack. Close the battery door. 4. Lay down the product on its side. WARNING: Keep bare hands away from the scarifier blade at all times. Use extreme caution and wear heavy-duty gloves when fitting, replacing, or cleaning the blade.
  • Page 13 7. Pull and slide down the blade to remove it. Dispose of the scarifier blade properly. 8. Insert the new scarifier blade and push in the blade shaft. 9. Reinstall the blade shaft cover. Turn the screws clockwise to tighten them. NOTE: Do not overtighten the screw.

  • Page 14: Emptying The Catcher

    EMPTYING THE CATCHER 1. Release the on/off lever to stop the product. Open the battery door. 2. Remove the isolator key. Remove the battery pack. Close the battery door. 3. Unhook the catcher from the grooves. 4. Remove the catcher. 5.
  • Page 15 CLEANING STORING PRODUCT 1. Release the on/off lever to stop the product. NOTE: Remove debris from the product with a soft, dry cloth and a stiff brush. NOTE: Do not use water to clean the product. 2. Open the battery door. Remove the isolator key.
  • Page 16 4. Unhook the catcher from the grooves. 5. Remove the catcher. 6. Remove the motor control cable from the motor control cable retainer. 7. Turn the handle knobs that secure the upper handle counterclockwise to loosen them. Remove the washer and screw on each side.
  • Page 17 9. Turn the handle lock on each side counterclockwise to remove it. 10. Remove the lower handle from the product. 11. Store the product in a cool, dry, and well-ventilated area that is inaccessible to children. Keep the product away from corrosive agents, such as garden chemicals and de-icing salts.

  • Page 18: Product Specifications

    1.33 kg Charger BCL3617S Weight 0.37 kg Compatible battery BPL3620D, BPL3626D2, BPL3640D2, packs BPL3650D2, BPL3660D, BPL3690D, BPL3612D, R36BTY2, R36BTY4, R36BTY5 REPLACEMENT PARTS Scarifier blade 09922801044 NOTE: Visit your local special orders desk or contact RYOBI customer service for replacement parts.
  • Page 20 Techtronic Industries Australia Pty Ltd 31 Gilby Road, Mount Waverley, VIC 3149 Melbourne, Australia Techtronic Industries N.Z. Limited Unit C, 70 Business Parade South, Highbrook, Auckland 2013, New Zealand RYOBI is a trade mark of Ryobi Limited, and is used under license. 099267001001-01...

Table of Contents