Table of Contents
Advertisement
Available languages
Available languages
5. Care and maintenance
Danger – risk of death from electric shock
Disconnect the mains plug from the socket before starting any cleaning work.
Warning - risk of cutting on the cutting rollers
Do not touch the cutting rollers.
Warning - damage to the device from moisture
Ensure, when cleaning, that no moisture penetrates the device in order to avoid
irreparable damage to it.
5.1 Emptying the container
Note
The status LED "Container full" on the " " button (9) ashes blue and the shredder
stops when the container is full.
• Switch the device off - as described in 4.2 Switching the device off - and disconnect
the mains plug.
• Pull the basket (5) out.
• Empty the container.
• Push the basket (5) back in.
• Reconnect the device - as described in 3. Installation/Setup - to the power supply.
5.2 Cleaning the device
• Switch the device off - as described in 4.2 Switching the device off - and disconnect
the mains plug.
• Clean the device with a dry cloth. In cases of heavy soiling, the cloth can be dampened
a little.
• Allow the device to dry completely afterwards.
• Reconnect the device - as described in 3. Installation/Setup - to the power supply.
5.3 Cleaning / oiling the cutting rollers
Note
• Oil the cutting rollers after each emptying of the waste paper basket in order to
prolong the shredder's service life.
• You can nd an appropriate selection of cleaning products at
www.hama.com.
• Switch the device on - as described in 4.1 Switching the device on.
5.3.1 Cleaning with Hama cleaners for shredders (item number: 113820)
• Apply the Hama cleaner for shredders (item number: 113820) in several strips onto a
piece of DIN A4-size paper.
• Insert the paper into the centre of the intake shaft (1). The cutting rollers switch on
automatically.
• Once the cutting process is complete, the device is ready for operation again.
5.3.2 Cleaning with cleaning paper
• Insert the cleaning paper into the centre of the intake shaft (1). The cutting rollers switch
on automatically.
• Once the cutting process is complete, the device is ready for operation again.
6. Troubleshooting
Error
Possible cause
The " " button (9) was
not pressed.
The cutting rollers do not
switch on automatically
The collecting container
when material to be
(5) is not inserted
shredded is inserted.
properly.
The connecting cable
(2) is not connected
correctly.
4
Error
The cutting rollers do not
switch on automatically
when material to be
shredded is inserted.
The status LED "Overload"
on the " " button (9)
The status LED
"Overheating" on the
" " button (9) lights up
solid red.
The status LED "Container
full" on the " " button
(9) ashes blue.
The cutting rollers
continue to run after the
shredding process has
been completed.
7. Technical data
Input voltage
Mains frequency
Max. power consumption
Dimensions (W x H x D)
Weight (net)
Weight (gross)
Basket capacity for paper and plastic cards
Max. noise level
Max. cutting performance - paper (70 gsm)
Max. cutting performance - paper (80 gsm)
Max. cutting performance - plastic cards
Max. cutting speed
Max. feed width for paper / plastic cards
Cutting size for paper / plastic cards
Max. constant operation time
Nominal rest period
Protection class (as per DIN 66399)
Safety levels (as per DIN 66399)
Remedy
* Thicker paper, moisture or any voltage other than that permitted may reduce the
Press the " " button
performance.
(9) until the status LED
8. Warranty disclaimer
"Ready" on the " "
button (9) lights up solid
All of the technical information, data and instructions regarding operation contained in these
blue.
operating instructions was up to date at the time of printing and is provided based on previous
experience and to the best of our knowledge.
Insert the collecting
Hama GmbH & Co KG assumes no liability and provides no warranty for damage resulting
container (5) properly.
from improper installation/mounting, improper use of the product or from failure to observe
the operating instructions and/or safety notes.
Ensure that the mains
plug is in the mains
socket.
Possible cause
The socket is not live.
The device is faulty.
Too much paper has been
inserted or it has been
drawn in at an angle.
ashes red.
The device has become
too hot.
The collecting container
(5) is full.
There is jammed paper in
the intake shaft (1).
Remedy
Check the domestic fuses.
Notify Customer Services.
Follow the steps in
4.5 Forward/reverse
modes and clear the
paper jam
Switch the device off and
allow it to cool down for
at least 45 minutes.
Empty the container
(5) as described in
5.1 Emptying the
container.
Follow the steps as
described in 4.5
Forwards / backwards
modes. Switch off the
device and check for
pieces of paper stuck in
the intake shaft (1).
220 - 240 V~
50 Hz
380 W
35.0 x 51.9 x 24.6 cm
10500 g
12200 g
20 litres
62 dB
11 sheets (DIN A4 paper)*
10 sheets (DIN A4 paper)*
1
1.8 m/minute
220 mm
2 x 12 mm
15 minutes
Min. 45 minutes
3
P-5 / T-5 / E-4
Advertisement
Table of Contents
