Pool/Spa Mode Menus; Circuit On/Off Menu (1/14) - Pentair SUNTOUCH Installation And User Manual

Pool/Spa Mode Menus

The following describes the 14 "Pool/Spa mode" menus. Displayed on the Main Menu screen is the menu
description and the menu number (1/14).

Circuit On/Off Menu (1/14)

Use the "Circuit On/Off" menu feature to manually switch ON/OFF the pool filter pump, auxiliary
circuits (AUX 1-3) and feature circuits (FT. 1-4). Switching circuits on or off will override any
programmed schedules that might already be assigned to these circuits. For more information about schedules,
see "Schedules Menu" on page 17.
POOL FILTER PUMP ON/OFF
pump relay on or off. When the pool filter pump switched on, the valve actuator will rotate to isolate the pool
water from the spa water, and switch the heater on (if enabled in the "Heat" menu). When this circuit relay
is switched on manually, it remains on until either you switch it off manually or the default 12 hours has
elapsed. The system default 12 hours can be changed from 1 to 23 hours (see "Circuit Timeout" page 24).
For example, if the filter pump is scheduled to automatically run from 9:00 AM to 5:00 PM daily, then the
filter pump is switched on manually at 9:00 PM, it will run continuously until the next day at 5:00 PM then
switch off. The schedule will then continue from then on. The top display line on the main status screen will
alternately display the current water temperature and the current air temperature (if the air sensor is enable,
see page 24 for details). If the pool filter pump is on, and the spa is switched on using the Up arrow button,
the main status screen will alternately display the current water temperature between "Pool" and "Spa" mode.
For HI-TEMP, LO-TEMP controls (SunTouch
Main Menu 1/14
Circuit On/Off
Circuit On/Off
Pool: ON
Pool 77°F / 79°F
9:45 AM HEATER
Use this feature to manually switch the auxiliary relay output circuit on or off. These auxiliary
AUX 1, AUX 2:
circuits can be assigned to operate the pool and spa system valves, lights and other equipment. When the
AUX 1 or AUX 2 circuit relay is switched on manually, it remains on until either you switch it off manually,
the default 12 hours has elapsed.
Main Menu 1/14
Circuit On/Off
Circuit On/Of
AUX 2: ON
AIR 71°F
11: 51AM AUX D3
AUX 3 circuit can be used as an extra assignment to control and electric heater, pump speeds or
AUX 3:
a valve actuator (see page 26 for details). For example, AUX 3 can be assigned to control the high speed
function of a 2-Speed pump or one of the four speeds of the IntelliFlo
can be selected/activated via a scheduled program or switched on/off manually. You can also assign a button
on the four-function QuickTouch
function.
Continue on next page.
: Use the "Circuit On/Off" Pool setting, to manually switch the pool filter
Control System single body system), see page 40.
®
Menu button > Right arrow button: Select Circuit On/Off (1/14).
Up/Down arrow button: Press the Up or Down button to toggle the POOL pump
circuit ON or OFF. After switching the Pool filter pump ON, the main status screen
displays the current pool water temperature. To adjust the set point temperature, use
the Left and Right arrow buttons.
Right arrow button: Select the "Circuit On/Off" Pool On/Off setting. Use this
function to manually switch the pool filter pump on or off.
Note: The Solar auxiliary relay (Valve C) on the SunTouch Control System
motherboard can operate a solar booster pump which will switch on when the filter
pump is running. Solar heat must also be available and the water must be below the
set point temperature setting. For more information, see "Solar Menu" on page 20.
Left arrow button: Press the Left button to return to the main status screen.
Menu button > Right arrow button: Select the Circuit On/Off 1/14 menu to
manually switch AUX 1, AUX 2 relay ON or OFF.
Right arrow button: Press the Right arrow button until AUX 1, AUX 2, or AUX 3
is displayed.
Up/Down arrow button: Press the Up/Down arrow button to toggle the AUX
circuit on or off.
Left arrow button: Press the Left button to return to the main status screen.
Wireless Remote (optional equipment) to control the high-speed pump
®
VS Pump. The pump speed control
®
SunTouch Control System Installation and User's Guide
®
13