LTS VSN8432 Quick Manual
  1. Manuals
  2. Brands
  3. LTS Manuals
  4. Network Hardware
  5. VSN8432
  6. Quick manual

LTS VSN8432 Quick Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Network Video Recorders
Quick Guide

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the VSN8432 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for LTS VSN8432

Summary of Contents for LTS VSN8432

  • Page 1 Network Video Recorders Quick Guide...

  • Page 2: Default Ip, Username And Password

    Default IP, Username and Password IP address: 192.168.1.30 NOTE! security, strongly Username: admin recommended to set a strong password of at least nine characters including all three elements: digits, letters special characters. Indicators Status Description PWR(Power) Steady on Connected to power. Steady on Normal.
  • Page 3 Figure 3-1 Model 1 Interface Description Interface Description Grounding Network ① ② Audio out CVBS output ③ ④ eSATA interface Alarm input/output ⑤ ⑥ AC power Power on/off ⑦ ⑧ Audio in HDMI 1 output ⑨ ⑩ VGA output HDMI 2 output ⑫...

  • Page 4: Disk Installation

    Interface Description Interface Description HDMI output ⑤ ⑥ ⑦ Network ⑧ DC power Disk Installation The illustrations are for reference only. The actual device may vary. Preparation  Prepare a 1# or 2# Philips screwdriver, a pair of antistatic gloves or a wrist strap.
  • Page 5 Connect the power cables and data cables. Put the cover back in place and tighten the screws. 4 or 8 HDD Installation 4.3.1 Remove Upper Cover Loosen the screws on the upper cover. Slide the upper cover backward, then lift it up to remove the cover. 4.3.2 Install Disks The installation steps for devices with mounting plate and disk bracket are different.
  • Page 6 Turn the upper mounting plate in the shown direction, then remove the plate. Repeat the steps to remove the lower mounting plate (for 8-HDD devices only). Secure the disks on the mounting plate. Fix the screws according to the figure below.
  • Page 7 Fasten the brackets installed with hard disks to the device. Connect the power cables and data cables. Power cable Data cable 8 or 16 HDD Installation Fix the mounting brackets to the disk with screws. With the disk interface side down, install the R (for right) and L (for left) bracket according to the figure below.

  • Page 8: Startup And Shutdown

     For front panel with buttons, press the buttons on both sides of the front panel.  For front panel with screws, loosen the screws on the front panel. Align the disk with the slot and slide the disk inward gently until it clicks. Repeat the steps to install all the disks.

  • Page 9: Local Operations

    CAUTION! Do not disconnect power when the NVR is operating or shutting down. Local Operations Add IP Devices Before you begin, make sure the devices are connected to your NVR via network. 6.1.1 Quick Add Follow the wizard to the fourth step. Select the devices to add in the discovered device list, and then click Add.
  • Page 10 NOTE!  After the device is added, if wrong username or password message shows in the preview window, click in the window toolbar and enter the correct username and password.  You can also click to add a device.  Click Search Segment to search for devices in a specified network segment.

  • Page 11: Web Login

    NOTE!  A 7*24 recording schedule is enabled by default. To set a recording schedule manually, right click and select Menu > Storage > Recording and then set recording type and time based on your needs.  If you choose Event type recording, you need to enable the corresponding alarm function and configure alarm-triggered recording/snapshot first.
  • Page 12 Disclaimer and Safety Warnings Copyright Statement No part of this manual may be copied, reproduced, translated or distributed in any form by any means without prior content in writing from our company (referred to as us hereafter). The product described in this manual may contain proprietary software owned by our company and its possible licensors.
  • Page 13  To the extent allowed by applicable law, in no event will our company be liable for any special, incidental, indirect, consequential damages, nor for any loss of profits, data, and documents.  The product described in this manual is provided on an "as is" basis. Unless required by applicable law, this manual is only for informational purpose, and all statements, information, and recommendations in this manual are presented without warranty of any kind, expressed or implied, including, but not limited to, merchantability, satisfaction with...
  • Page 14  Minimum port mapping: Configure your router or firewall to open a minimum set of ports to the WAN and keep only the necessary port mappings. Never set the device as the DMZ host or configure a full cone NAT. ...
  • Page 15  Do not remove the seal from the device body without consulting our company first. Do not attempt to service the product yourself. Contact a trained professional for maintenance.  Always disconnect the device from power before attempting to move the device. ...
  • Page 16  If the battery compartment does not close securely, stop using the product and keep it away from children.  If you think batteries might have been swallowed or placed inside any part of the body, seek immediate medical attention. ...

Table of Contents