Related Manuals for Kampmann PowerKon QE
Summary of Contents for Kampmann PowerKon QE
- Page 1 PowerKon QE ► Assembly, installation and operating instructions Keep these instructions in a safe place for future use! Issue08/22EN SAP No.1720507...
-
Page 3: Table Of Contents
Table of contents 1 General ..........................5 1.1 About these instructions ........................1.2 Explanation of Symbols.......................... 2 Safety............................ 6 2.1 Correct use............................. 2.2 Limits of operation and use........................2.3 Risk from electrocution!......................... 2.4 Personnel requirements - Qualifications ....................2.5 Personal Protective Equipment ......................3 Transport, storage and packaging.................. - Page 4 10.3.1 Clean the inside of the unit ........................27 11 Faults ............................ 28 11.1 Fault table.............................. 28 11.2 Start-up after rectification of fault ......................28 12 Certificates..........................29 Table ............................. 32...
-
Page 5: General
PowerKon QE Assembly, installation and operating instructions General About these instructions These instructions ensure the safe and efficient handling of this equipment. These instructions form an integral part of the equipment and have to be kept in the direct vicinity of the equipment and available to personnel at all times. -
Page 6: Safety
PowerKon QE Assembly, installation and operating instructions Safety This section provides an overview of all important safety aspects to ensure optimum protection of personnel as well as safe and trouble-free operation. In addition to the safety instructions in these operating instructions, the valid safety, accident pre- vention and environmental protection regulations must be observed for the area of use of the unit. -
Page 7: Risk From Electrocution
PowerKon QE Assembly, installation and operating instructions IMPORTANT NOTE! Warning of misuse! In the event of misuse, as itemised below, there is a danger of limited or failing operation of the unit. En- sure that the airflow can circulate freely. -
Page 8: Personnel Requirements - Qualifications
PowerKon QE Assembly, installation and operating instructions Personnel requirements - Qualifications Expertise The installation of this product requires specialist knowledge of heating, cooling, ventilation, installation and electrical engin- eering. This knowledge, generally learned in professional training in one of the fields mentioned above, is not described sep- arately. -
Page 9: Transport, Storage And Packaging
IMPORTANT NOTE! Warranty claims can only be made within the applicable period for complaints. (More information is avail- able in the T&Cs on the Kampmann website) IMPORTANT NOTE! 2 people are needed to transport the unit. Wear personal protective clothing when transporting the unit. -
Page 10: Storage
PowerKon QE Assembly, installation and operating instructions Storage Store packaging under the following conditions: Do not store outdoors. Store in a dry and dust-free place. Store in a frost-free place. Do not expose to aggressive media. Protect from direct sunlight. -
Page 11: Technical Data
PowerKon QE Assembly, installation and operating instructions Technical data PowerKon QE Control signal Air volume flow Nominal current Sound pressure Sound power Heat output [W] Weight [kg] [m³/h] level [dB (A)] level [dB(A)] Casing length 825 mm, casing height 200 mm, casing width 205 mm 15.4-16.7... -
Page 12: Construction And Function
PowerKon QE are free-standing decentralised units for the heating of room air with an electric heating coil and EC tangential fan for use in hotels, offices and business premises etc. PowerKon QE is an ideal solution when the use of an LPHW convector or coil is impossible. -
Page 13: Installation And Wiring
PowerKon QE Assembly, installation and operating instructions Installation and wiring Requirements governing the installation site Only install and assemble the unit if the following conditions are met: Make sure that the unit is securely suspended/standing. Ensure that the airflow can circulate freely. -
Page 14: Installing The Unit
PowerKon QE Assembly, installation and operating instructions 6.2.1 Installing the unit Dimensions Fig. 2: Dimensions of the PowerKon QE Window side Room side 825 mm // 1250 mm // 1700 mm 400 mm // 835 mm // 1270 mm Fixing points Fig. 3: All dimensions in mm... - Page 15 PowerKon QE Assembly, installation and operating instructions...
- Page 16 PowerKon QE Assembly, installation and operating instructions...
- Page 17 PowerKon QE Assembly, installation and operating instructions...
- Page 18 PowerKon QE Assembly, installation and operating instructions...
-
Page 19: Fitting The Grille
PowerKon QE Assembly, installation and operating instructions 6.2.2 Fitting the grille High surface temperatures occur at the electric heating coil. For this reason, additional grille fixings are factory-fitted on both longitudinal sides of the duct as a safety guard. They can be removed using a screwdriver. The grille fixing only needs to be removed on one side, the electrical connection side, when wiring. -
Page 20: Electrical Connection
Electromechanical connection, 230 V (*00) Circuit description PowerKon QE PowerKon QE requires a 230 V AC power supply. The output of the electric heating coil and EC fan can be controlled continuously variably by a 0-10 V DC signal. Internal safety shut-down: In the event of improper use, the heat output is reduced or switched off. - Page 21 Assembly, installation and operating instructions Dip switch settings LED status messages Terminal assignment X1 Terminal assignment X2 Fig. 5: PowerKon QE circuit board Terminal assignment mains Mains connection (230 V/50 Hz) Fault Potential-free fault alert output (max. load 60 V AC/DC 1 A)
- Page 22 Alternating = On (0.5 sec.) Off (0.2 sec.) On (0.1 sec.) Off (0.2 sec.) ... Note these points in the following layout plans for PowerKon QE with electromechanical control 230 V(*00): Comply with the details on cable types and cabling with due consideration of VDE 0100.
- Page 23 PowerKon QE Assembly, installation and operating instructions Control 0-10V DC via BMS...
- Page 24 PowerKon QE Assembly, installation and operating instructions Control via climate controller type 146928...
-
Page 25: Pre-Commissioning Checks
PowerKon QE Assembly, installation and operating instructions Pre-commissioning checks Before initial commissioning, check whether all the necessary conditions have been met so that the unit can function safely and properly. Structural tests Check that the unit is securely standing and fixed. -
Page 26: Operation
2- and 4-pipe applications, surface-moun- ted wall installation on a flush-mounted box setpoint display by threshold arrows heating or cooling via active 0-10 V signals option for external room sensor connection digital input for ECO operation for use with PowerKon QE, max. 5 units... -
Page 27: Maintenance
PowerKon QE Assembly, installation and operating instructions Maintenance 10.1 Securing against reconnection DANGER! Risk of death by unauthorised or uncontrolled restart! Unauthorised or uncontrolled restarting of the equipment can result in serious injury or death. Before restarting, ensure that all safety devices are fitted and working properly and that there is no haz- ard to humans. -
Page 28: Faults
PowerKon QE Assembly, installation and operating instructions Faults The following chapter describes possible causes of faults and the work needed to rectify them. Should faults occur frequently, shorten the maintenance intervals in line with the actual loading on the unit. -
Page 29: Certificates
PowerKon QE Assembly, installation and operating instructions Certificates EU-Konformitätserklärung EU Declaration of Conformity Déclaration de Conformité CE Deklaracja zgodności CE EU prohlášení o konformite KAMPMANN Wir (Name des Anbieters, Anschrift): GMBH & Co. KG Friedrich-Ebert-Str. 128-130 We (Supplier’s Name, Address):... - Page 30 PowerKon QE Assembly, installation and operating instructions Gemäß den Bestimmungen der Richtlinien: Following the provisions of Directive: Conformément aux dispositions de Directive: Zgodnie z postanowieniami Dyrektywy: Odpovídající ustanovení směrnic: 2014/30/EU EMV-Richtlinie 2014/35/EU Niederspannungsrichtlinie Frank Bolkenius Lingen (Ems), den 07.07.2022 ___________________________________...
- Page 31 PowerKon QE Assembly, installation and operating instructions...
-
Page 32: Table
PowerKon QE Assembly, installation and operating instructions Table Tab. 1 Limits of operation ..............................6 Tab. 2 Operating voltage ..............................6 Tab. 3 Maximum electrical rating values, electromechanical model 230 V............... 20... - Page 36 Country Contact Kampmann UK Ltd. Dial House, Govett Avenue Shepperton, Middlesex, TW17 8AG T +44 1932/ 228592 Great Britain F +44 1932/ 228949 E info@kampmann.co.uk W Kampmann.co.uk...
Need help?
Do you have a question about the PowerKon QE and is the answer not in the manual?
Questions and answers