Troubleshooting Guide - Intermatic EJ351 Installation And User Instructions

Programming Using the 24-HOUR Method
Use this procedure to automatically program, letting the switch
timer "record" your ON/OFF activities over a 24-hour period,
storing them as programmed settings.
1. Move the control lever to the OFF-CLEAR position for about
20 seconds. The red indicator light will go off and any previ-
ous time settings will be cleared from memory.
2. Move the control lever to the ON position. The Red indicator
light will start flashing.
3. Press the dial as an ON/OFF switch to turn lights ON and OFF
at the ON and OFF times you desire for the first 24 hours.
4. At the end of the 24-hour period, the switch timer will be pro-
grammed and the Red indicator light will stay ON, indicating
that the switch timer is in AUTOMATIC mode.
Reviewing the Settings Stored in Memory
Use this procedure to check the settings programmed into the
switch timer.
NOTE: Reviewing will not change or delete the program. The
only way to delete a program is to move the control lever to
the OFF-CLEAR position for about 20 seconds. This clears the
entire memory.
1. Make sure the switch timer is in AUTOMATIC mode, with the
Red indicator light flashing.
2. Rotate the time dial clockwise at least one click, stopping at
the nearest half hour to the present time.
3. Press the dial once to start the Review cycle. The Red indica-
tor light will go OFF.
Observed Problem
The Switch Timer cannot be programmed using the
RAPID method.
The Switch Timer does not turn lights ON and OFF
automatically, as programmed.
The Switch Timer does not turn light ON or OFF when
pressing on the Dial.
The Switch Timer is warm to the touch.
The controlled light flickers or goes to half brightness.
If within one (1) year from the date of purchase, this product fails due to a defect in material or workmanship, Intermatic Incorporated will repair or replace it, at its sole option, free of charge. This warranty is
extended to the original household purchaser only and is not transferable. This warranty does not apply to: (a) damage to units caused by accident, dropping or abuse in handling, acts of God or any negligent
use; (b) units which have been subject to unauthorized repair, opened, taken apart or otherwise modified; (c) units not used in accordance with instructions; (d) damages exceeding the cost of the product; (e)
sealed lamps and/or lamp bulbs, LED's and batteries; (f) the finish on any portion of the product, such as surface and/or weathering, as this is considered normal wear and tear; (g) transit damage, initial installa-
tion costs, removal costs, or reinstallation costs.
INTERMATIC INCORPORATED WILL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL
DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU. THIS WARRANTY IS IN LIEU OF ALL OTHER EXPRESS OR IMPLIED WARRANTIES. ALL IMPLIED WARRANTIES, INCLUDING
THE WARRANTY OF MERCHANTABILITY AND THE WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, ARE HEREBY MODIFIED TO EXIST ONLY AS CONTAINED IN THIS LIMITED WARRANTY, AND SHALL
BE OF THE SAME DURATION AS THE WARRANTY PERIOD STATED ABOVE. SOME STATES DO NOT ALLOW LIMITATIONS ON THE DURATION OF AN IMPLIED WARRANTY, SO THE ABOVE LIMITATION MAY
NOT APPLY TO YOU.
This warranty service is available by either (a) returning the product to the dealer from whom the unit was purchased, or (b) mailing the product, along with proof of purchase, postage prepaid to the authorized
service center listed below. This warranty is made by: Intermatic Incorporated/After Sales Service/7777 Winn Rd., Spring Grove, Illinois 60081-9698/815-675-7000 http://www.intermatic.com Please be sure to
wrap the product securely to avoid shipping damage.

Troubleshooting Guide

Was the timer correctly programmed according to the instructions? If not, try again.
Make sure the Control Lever is in the ON position.
Make sure the Red Indicator Light is flashing before beginning programming.
Make sure you have set the Current Time before programming ON/OFF times.
Make sure you are pressing the Dial fully during the programming sequence.
Was the timer correctly programmed according to the instructions? If not, try again.
Make sure the timer is not accidentally in MANUAL mode, with the Red indicator light OFF.
Make sure the controlled light bulb(s) is tight in its socket and is not burned out.
Check the wiring for any loose connections.
Make sure the controlled light bulb(s) is tight in its socket and is not burned out.
Check the wiring for any loose connections.
Check for a burned out fuse or circuit breaker.
Some warmth is normal. Be sure the combined light bulb wattage does not exceed 500 watts.
Recheck the wiring.
LIMITED ONE-YEAR WARRANTY
INTERMATIC INCORPORATED, SPRING GROVE, ILLINOIS 60081-9698
4. Rotate the time dial slowly clockwise, observing the time
shown on the dial when the light controlled by the switch
timer goes ON and OFF.
5. Press the dial once to end the Review cycle. The Red indicator
light will go ON and stay ON, indicating that the switch timer
is in AUTOMATIC mode.
Everyday Use of the EJ351 Switch Timer
• The time dial does not rotate automatically to function as a
clock (reflecting the time of day). After programming is com-
plete, the time dial functions only as an ON/OFF switch.
• The Switch Timer can be used in either of two modes. To
switch between modes, quickly press the dial twice:
- AUTOMATIC MODE: The Switch Timer will turn the light
ON or OFF according to programmed settings. RED indica-
tor light stays ON when in Automatic Mode.
NOTE: Even in AUTOMATIC Mode, press the dial to
manually turn the light ON or OFF. While this will over-
ride the current program, it will not disturb the next one.
- MANUAL MODE: Programmed settings are inactive, and
the Switch Timer will only turn the light ON or OFF when
you push on the dial. RED indicator light stays OFF when in
Manual mode.
• When the controlled light bulb burns out, the red indicator
light will also go off and timer settings are affected. Change
the bulb as follows:
a. Move the Control Lever to the OFF-CLEAR position.
b. Replace the bulb.
c. Move the control lever back to the ON position.
d. Reprogram the timer settings.
What to Do
158--00545