Table of Contents
Advertisement
Quick Links
RS-232, IP, IR and Front panel Control with Status LCD Display
CUSTOMER
SUPPORT
INFORMATION
HSM-44-UHD
4K 4X4 HDMI Matrix Switch
Supports 4K UHD resolution
HDCP 2.2 and 1.4 compliant with EDID Management
Analog and Digital Extracted Audio Outputs
Order toll-free in the U.S. 800-959-6439
FREE technical support: 714-641-6607 or support@halltechav.com
Hall Technologies, 1163 Warner Ave. Tustin, CA 92780
www.halltechav.com
User's Manual
UMA1293 Rev NC
Advertisement
Table of Contents
Related Manuals for Hall Technologies HSM-44-UHD
Summary of Contents for Hall Technologies HSM-44-UHD
- Page 1 User’s Manual HSM-44-UHD 4K 4X4 HDMI Matrix Switch Supports 4K UHD resolution HDCP 2.2 and 1.4 compliant with EDID Management RS-232, IP, IR and Front panel Control with Status LCD Display Analog and Digital Extracted Audio Outputs UMA1293 Rev NC Order toll-free in the U.S. 800-959-6439 CUSTOMER FREE technical support: 714-641-6607 or support@halltechav.com SUPPORT Hall Technologies, 1163 Warner Ave. Tustin, CA 92780 INFORMATION www.halltechav.com...
-
Page 3: Table Of Contents
3.4 Rear Panel ..................8 4.0 EDID management ..............10 4.1 EDID Configuration ..............10 6.0 Network Settings ................. 10 7.0 Serial & Telnet Commands ............11 8.0 Troubleshooting ................14 8.1 Contacting Hall Technologies ............14 9.0 Specifications ................15 © Copyright 2021 Hall Technologies... - Page 4 HSM-44-UHD TRADEMARKS USED IN THIS MANUAL Hall Technologies and its logo are trademarks of Hall Technologies. Any other trademarks mentioned in this manual are acknowledged as the property of the trademark owners. FCC RADIO FREQUENCY INTERFERENCE STATEMENT This equipment generates, uses, and can radiate radio frequency energy and if not installed and used properly, that is, in strict accordance with the manufacturer’s instructions, may cause interference to radio communication. It has been designed to comply with the limits for a Class B computing device in accordance with the specifications in Subpart B of Part 15 of FCC rules, which are intended to provide reasonable protection against such interference when the equipment is operated in a commercial environment. Operation of this equipment in a residential area is likely to cause interference, in which case the user at their own expense will be required to take whatever measures may be necessary to correct the interference. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. © Copyright 2021 Hall Technologies...
-
Page 5: Introduction
The 4K matrix is a 4x4 cross-point switch in a compact 1-RU enclosure. The HSM-44-UHD supports HDMI resolutions up to 4K @ 60 Hz 4:4:4. It also supports HDCP 2.2 and 1.4, 3D, deep-color and PCM, Dolby, DTS, and HD audio standards. -
Page 6: Package Contents
HSM-44-UHD 2.0 Package Contents (1) Model HSM-44-UHD (1) External Universal Power Supply (1) IR Remote (2) Rack mounting brackets with (6) screws (1) IR Detector (for use with IR Remote) (1) 3 Pin screw-terminal (for use with RS-232 connector) (1) User’s Manual Card 3.0 Operation 3.1 General Operation 3.1.1 Front Panel Functions The front panel can be used for the following purposes: • View current input/output routings (ties) on LCD • Make new ties either starting from input or output • Lock or unlock the front panel All the front panel buttons have built-in LEDs to help with their operation. The LOCK button is used to enable or disable the keys on the front panel and IR remote control. Locking the front panel is intended to prevent inadvertent actions for example, if the buttons are pressed unintentionally. Note that when the front panel is locked, the IR remote function is also locked, the other means to control the matrix (RS-232, Telnet or WebGUI) are still functional. Lock the front panel by pressing the LOCK button for 3 Seconds. The display will show ‘Panel Locked!’ and the LOCK button LED will turn on. Unlock the front panel by pressing the LOCK button for 3 Seconds. The display will show ‘Panel Unlocked!’ and the LOCK button LED will turn off. Attempting to control the matrix with the buttons or IR remote control while the unit is ‘Locked’, results in the LCD displaying ‘Panel Locked!’. Note that the IR Remote Control POWER control will still function even if the system is Locked. © Copyright 2021 Hall Technologies... - Page 7 4X4 HDMI Matrix Switch with 4K HDMI 3.1.2 Front Panel Operation. The front panel pushbuttons have built-in LEDs which represent the buttons state. Button LEDs can be off, blinking or on (solid). Front panel button LED states 3.1.3 Reading the LCD routing configuration. Routing information is displayed on the LCD. The ‘IN’ row on the LCD changes to represent the current routing status. The ‘OUT’ values are fixed or show an output as blank by displaying an ‘x’ in that position. In the above example, the routing configuration can be understood from the output end as follows: Output 1 is tied to Input 1. § Output 2 is tied to Input 1. § Output 3 is tied to Input 2. § Output 4 is tied to Input 2. § 3.1.4 Turning the unit on and off. The system can be turned on and off via the IR Remote Control, RS-232 or Telnet. © Copyright 2021 Hall Technologies...
- Page 8 HSM-44-UHD 3.1.5 Making AV Routing or "Ties" from the Front Panel. Users can initiate “ties” either from the HDMI OUTPUT or INPUT point of view. For most users it is more logical to initiate ties starting with the OUTPUT. Think of it as: “I want OUTPUT 1 to get its video from INPUT 2”. 3.1.6 Making a tie starting from the OUTPUT. To tie an output to an input, use the following steps: 1. Press the desired output button. The button for the currently tied INPUT will light up. 2. Press the input button you want to tie to. This selected input button will start blinking. The blinking button designates it as a “desired” choice; the actual tie is not made until the SET button is pressed. 3. Press the SET button. If you do not press the SET button with ~5 seconds, the process will time out and the button LEDs go out. Example: Route output 3 to input 3 (when currently tied to Input #2) © Copyright 2021 Hall Technologies...
- Page 9 4X4 HDMI Matrix Switch with 4K HDMI 3.1.7 Making a tie starting from input Routing from the input end is like the above, but an input can be routed to multiple outputs all at one time. 1. Press one of the input buttons. That button LED will light up solid along with ALL the outputs currently routed from that input. 2. Select all the outputs you wish to route to. There can be multiple desired outputs, and all will be blinking until the SET button is pressed. To remove an output, press the blinking output again. 3. Press SET to apply the changes. Example: Route Input 1 to Output 1, 2 and 3 © Copyright 2021 Hall Technologies...
-
Page 10: Presets (Memorized Routing Patterns)
HSM-44-UHD 3.1.8 Blanking Outputs. Any HDMI output can be ‘blanked’ using either the WebGUI, RS-232 or Telnet commands. 3.2 Presets (Memorized Routing Patterns) 3.2.2 Recalling Presets. Preset routing configurations can be selected by using the IR Remote control, RS- 232 or WebGUI. 3.2.3 Editing Presets. Preset routing configurations can be created by using RS-232 or the WebGUI. -
Page 11: Rear Panel
4X4 HDMI Matrix Switch with 4K HDMI 3.4 Rear Panel Rear Panel HDMI Inputs: Connect to HDMI sources. HDMI Outputs: Connect to HDMI displays. Digital/Line Audio Outputs: Connect to external sound system Control Inputs: The IP CTRL port connects to a user’s network LAN. It is used to control the matrix using Telnet or to access the internal WebGUI. The RS-232 terminal block connects to external serial control systems (115.2k baud). The IR IN port connects to the supplied IR Detector cable if the matrix switcher does not have a direct line of sight of the IR remote. © Copyright 2021 Hall Technologies... -
Page 12: Edid Management
HSM-44-UHD 4.0 EDID management The HSM-44-UHD gives users the flexibility to configure the EDID for each input. The source for the EDID data associated with each input can be from one of 5 standard built-in choices or copied from any of the TVs connected to a particular output. By default, the EDID for all inputs are set to 4Kx2K@30 video with 2-channel audio. 4.1 EDID Configuration Via RS-232, Telnet or WebGUI, the user can specify an EDID table and load it into any selected input port on the matrix. HSM-44-UHD comes with 5 common EDIDs saved in its internal memory, or you can copy the EDID of any of the devices connected to outputs. Note to change an Input to ‘Copy from Output x’, you must have a SINK device connected at the time of configuration. The SINK can be changed later, but it must be connected during configuration for the change to become valid. Index EDID Description 1080p Video, 2 Ch Audio 1080p Video, 5.1 Ch Audio 4kx2k@30Hz Video, 2 Ch Audio 4kx2k@60Hz Video, [4:4:4] 2.0 Ch Audio 4kx2k@60Hz Video, [4:4:4] 5.1 Ch Audio Copy from Output 1 Copy from Output 2 Copy from Output 3 Copy from Output 4 6.0 Network Settings As shipped from the factory (or after a factory default), the HSM-44-UHD IP address is set for static IP address of 192.168.1.50. To change the IP address or to switch to DHCP, you must use either RS-232 or Telnet. For example, to change the IP address via RS-232: • Connect a PC with Terminal-Emulator software to the RS-232 port. -
Page 13: Serial & Telnet Commands
• Commands are in ASCII format. • Commands are case in-sensitive. • Use a single <CR> character to terminate each command. • Responses from the matrix are terminated with <CR><LF>. • Other than Power command (PW1), the matrix must be powered on. • Unknown commands respond with “INVALID COMMAND”<CR><LF>. • After plugging power to the matrix, you must wait ~45 seconds for it to fully boot up before sending any commands. • Command characters should be sent continuously without pauses. If you pause for more than 5 seconds, the command will automatically terminate. • When the front panel buttons are used, some serial responses will be sent out the RS-232 port. Response Command Description Query Device Name HSM-44-UHD DN[16 Characters] Set Device Name Device name set CVn,m Connect output n to input CVn,m n= Output [1-4] m= Input [1-4] or m=x to blank the specified Output CV*,m Connect all outputs to CV1,m m= Input [1-4] input m... - Page 14 HSM-44-UHD Response Command Description HSM Reboot the system FW Version:?.?? CV1,? CV2,? CV3,? CV4,? LK? IP ???.???.???.??? MAC ??-??-??-??-??-?? DHCP? ? represents the value of the setting being displayed LKn Lock Front Panel LKn n = 0 Lock OFF n = 0 Lock OFF n = 1 Lock ON n = 1 Lock ON Lock Status Query LKn n = 0 Lock OFF n = 1 Lock ON ESn,m Set EDID for a particular ESn,m n = Input # [1-4] input to n (default is 2) m = Input # [1-4] m = EDID Index n = EDID Index [1-9] 1080p/60Hz, 2.0 ch 1080p/60Hz, 5.1 ch...
- Page 15 4X4 HDMI Matrix Switch with 4K HDMI Response Command Description GW xxx.xxx.xxx.xxx Assign Static Gateway GW xxx.xxx.xxx.xxx Address (DHCP must be off) DHCPn Enable DHCP DHCP0 n = 0 (DHCP off) or n = 1 (DHCP on) DHCP1 DHCP DHCP Status Query DHCPn n = 0 (DHCP off) n = 1 (DHCP on) Firmware Version Query FW Version:x.xx Reboot the system As shown in the “HSM” Response Restore factory defaults As shown in the “HSM” Response Note: Resets all parameters including network settings PSx Saves the current PSx configuration to the x=Preset # [1 to 4] preset specified X = Preset # [1-4] PSx=1,m/2,m/3,m/4,m Define and save a Preset PSx=1,m/2,m/3,m/4,m...
-
Page 16: Troubleshooting
HSM-44-UHD 8.0 Troubleshooting There are no field serviceable parts or circuits in the device. If you think the device is malfunctioning (or have no connectivity), please try to use the following methods for troubleshooting: • Try Rebooting the device by cycling the input power. • Restore factory defaults (FD command) using the RS-232, Telnet or WebGUI interface. 8.1 Contacting Hall Technologies If you determine that your Matrix Switch is malfunctioning, do not attempt to repair the unit. Instead contact Hall Technologies Technical Support at 800-959-6439 or via email at support@halltechav.com. To return the unit to Hall Technologies you must first get a Return Authorization (RMA) number. Package the unit carefully, if returning. We recommend using the original container the product came in. © Copyright 2021 Hall Technologies... -
Page 17: Specifications
4X4 HDMI Matrix Switch with 4K HDMI 9.0 Specifications Video Input Ports (4) HDMI 2.0 Video Output Ports (4) HDMI 2.0 HDCP HDCP 2.2 and HDCP 1.4 HDMI Bandwidth 18 Gbps HD Resolutions Up to 4K60 (4:4:4) PC Resolutions VGA through WQXGA Audio Output Ports (4) TOSLINK (S/PDIF digital supports all formats listed below) (4) 3.5 mm (Analog Stereo, L/R, supports only 2-channel formats) PCM 2.0, PCM 5.1, PCM 7.1, Dolby 5.1, DTS 5.1, DD+, D-TrueHD, DTS-HD 16/20/24 bits per sample and up to 96 KHz Sampling Rate... - Page 18 © Copyright 2021. Hall Technologies All rights reserved. 1163 Warner Ave., Tustin, CA 92780 Ph: (800) 959-6439...