Important Safety Instructions 1. Read these Instructions. 2. Keep these Instructions. 3. Heed all Warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with a dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
Additional Warnings and Precautions Do not look directly into the projector light. 2. Don’t touch the project lens Mains adapter is used as disconnect device and it should remain readily operable during intended use. In order to disconnect the apparatus from the mains completely, the mains plug should be disconnected from the mains socket outlet completely.
FCC Warning This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Remove & Close The Lens Cover Remove the lens cover before using Close the lens cover when unit is not using Placing of Your Projector Your projector can be installed in four different configurations (see picture below): Front Table: Select this location with the projector placed near the floor in front of the screen.
A projector mount is required to install the projector in a ceiling. A special rear projection screen is required. To reduce Image Distortion Move the projector as close to the center of the screen as possible. The light beam from the projector should be perpendicular to the screen for a rectangular or square image.
Adjust The Vertical Location Follow below picture to adjust the vertical location. Adjust The Focus And Keystone Follow below picture to adjust the focus and trapezoidal screen. Adjust the focus by turning the knob while observing the image pixels near the center of the screen.
Controls of Remote Install / Remove Batteries of Remote Remove the battery compartment cover on the back of your remote by carefully sliding to open. The battery cover can then be lifted away. Fit the correct batteries (not included), referring to the polarity markings. Finally, replace the cover. NOTES: ...
Controls of Projector LENS Buttons ANGEL ADJ. Knob Buttons AC IN Socket Button FOCUS ADJ. Knob Audio out Jack TRAPEZOIDAL ADJ. Knob AV IN Jack POWER Indicator TF Card Slot HDMI 1 & 2 Ports POWER Button USB Port RETURN Button VGA IN Port SOURCE...
Install Power Adapter Follow below picture to connect power cable Connect small end of cable FIRST. Plug the AC plug to power outlet. WARNING: Before connecting to the power supply, ensure that the supply corresponds to the information on the rating label at the back of the apparatus. Main Button Operation - Press the button to switch on unit, press again to turn off.
- Press to mute the audio. Press again to resume. Connect HDMI Show The Image On Projector Screen Refer to the following picture to connect a set top box, a BD/DVD player or a streaming player to the HDMI input. Turn off the unit before connect HDMI cable.
Connect VGA Show The Image On Projector Screen Follow below picture to connect VGA cable and device. Turn off the unit before connect VGA cable. Press the button to turn off power of your projector before connection. After connect, press the button to turn on unit and power indicator will light GREEN Press the...
46.9 40.3 1024x768 48.4 56.5 NOTE: In order to get the sound from the unit, please connect AV IN cable when you connect VGA input. Connect Audio Output ( Aux Out / Line Out / Earphones) Follow below picture to connect audio cable and device. Press the button to turn off power of your projector before connection.
Using TF Card And USB Playback DMP (Media Player) Install USB / TF device: 1. Turn off the unit before install USB / TF card. 2. Install the USB device into USB port. 3. After connect, press the button to turn on unit and the power indicator light GREEN.
function screen show on lower (figure 3). Use the button to select icon and press the button to play special function. Using Bluetooth Playback Pairing is the term used when two Bluetooth devices are connected wirelessly for the first time. This allows the devices to see each other and sets up a one to one communication channel between both devices.
Multi-screen interactive connection for phone and projector First, ensure the projector and the mobile is connected to the same wireless network Follow below steps to set up. Support Screen Mirroring Settings (IOS mobile) 1. Press the / SOURCE button to enter and use buttons to select the Screen Mirroring mode.
Page 18
settings 4. Click to select “RKcast-XXXXXX” (XXXXXX is numbers and letters. It show on the “Screen Mirroring” page) on the mobile settings. The mobile device contents will mirror on the projector screen Android Mirroring Settings (DLNA mode) 1. Press the / SOURCE button to enter and use buttons to select the Air Play mode.
Using Projector Menu 1 Press / MENU button to enter projector menu, press buttons to select PICTURE menu. This Picture menu showed on right upper of view screen. to select different picture effect to Medium / Soft / User / Vidid. Use to select Contrast / Brightness / Color / Sharpness digit If chose User item.
Duration time Off / 5S / 10S / 15S / 20S / 25S / 30S Press buttons repeatedly to select Front / Rear Ceiling / Front Ceiling / Rear For service center use only. Specifications Bluetooth Version Light Source Type HDMI Input Supported 1080p , 1080i , 720p, 576i , 480p, and 480i Video Resolution.
Page 22
user is encouraged to try to correct the interference by one or more of the following measures: -- Reorient or relocate the receiving antenna. -- Increase the separation between the equipment and receiver. -- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.