Related Manuals for Cirs QA Phantom 008Z
Summary of Contents for Cirs QA Phantom 008Z
- Page 1 MRgRT Motion Management QA Phantom Model 008Z IMAGE ACQUISITION • TREATMENT PLANNING • DOSE DELIVERY USER GUIDE 900 Asbury Ave • Norfolk, Virginia 23513 • USA • Tel: 757-855-2765 • WWW.CIRSINC.COM...
-
Page 2: Table Of Contents
. . . . . . . . . . . . 8 CIRS Motion Control Software . . . . . . . . . . . -
Page 3: Overview
The integration of MR imaging in radiation therapy facilitates real time motion management. • Non-ferromagnetic materials The CIRS MRgRT Motion Management QA phantom is designed to address => MR safe such needs. The phantom is MR Safe due to the use of piezoelectric motors and non-ferro-magnetic materials. -
Page 4: Safety
Controller. WARNING: DUE TO THE NEED TO SHIELD ACTUATOR FOR EMI, HEAT IS GENERATED INSIDE. THEREFORE, CIRS STRONGLY RECOMMENDS THAT THE PHANTOM IS RUN IN SESSIONS OF LESS THAN 1 HOUR WITH HALF HOUR BREAKS BETWEEN SESSIONS. -
Page 5: Unpacking Instructions
Unpacking Instructions Before you open the case check the Remove wall partition from the case and Remove cables. three Drop ‘N’ Tell indicators on the set aside. right side of the case. Drop ‘N’ Tell shipping damage indicator shows when a case has been dropped in transit and contains potential dam- aged goods. -
Page 6: Model 008Z Assembly Procedure
Assembly Procedure Place rod into phantom body and screw Insert ion chamber into each cavity hole. Place phantom body on base plate into the rod and actuator together. (Moving target) the 4 slots as shown in image above. Insert ion chamber into each cavity hole. Insert ion chamber into each cavity hole. -
Page 7: Model 008Z Cables And Connections
Cables and Connections WARNING: FOLLOW THE CABLE CONNECTION STEPS AS THEY ARE PRESENTED IN THIS USER GUIDE. CONNECTING THE CABLES WITH THE CONTROLLER “POWER ON” CAN SERIOUSLY DAMAGE THE PHANTOM’S ELECTRONICS. Attach ethernet cable to back of Plug the Cable DB26 m/m to back of Plug power cord into the back of controller and to back of actuator. -
Page 8: An Ethernet Connection
“Install Driver”. Adapter” folder found on the provided USB drive or download the zipped folder from the CIRS website. Archive to a known location and select autorun. Note: The provided “USB to Network Adapter” can act as Plug and Play device on some PC but CIRS recommends doing the installation of the driver as outlined above. - Page 9 Select Internet Protocol Version 4 (TCP/IPv4) and click on prop- Providing that the installation of the “USB-to-Network Card” erties was successful, the newly installed Network Adapter should show as “ASIX AX88179 USB 3.0 to Gigabit Ethernet Adapter”. Select it’s Properties using the right mouse click menu as shown below.
-
Page 10: Cirs Motion Control Software
If the end-user is offline during use of the phantom, it is recom- INTRODUCTION mended that a copy of the CIRS Motion Control User Manual is CIRS Motion Control is an application which allows you to control downloaded and saved. Once a copy of the manual is saved in a... -
Page 11: Model 008Z Specifications
1.1 kg (2.4 lbs) Note: Customers must complete their order with the purchase of the moving rod. *Refer to separate CIRS cavity code list for available chamber cavities. It is recommended to choose the same cavities for both the body and rod. -
Page 12: Warranty
CIRS not to comply with documented order specifications. You accessories must return the product to CIRS within 30 calendar days of the issu- ance of the RMA. All returns should be packed in the original cases There are no warranties, expressed or implied, including without... -
Page 13: Notes
NOTES:... - Page 14 NOTES:...
- Page 15 NOTES:...
- Page 16 COMPUTERIZED IMAGING REFERENCE SYSTEMS, INC. 900 Asbury Ave Norfolk, Virginia 23513 USA Toll Free: 800.617.1177 Tel: 757.855.2765 Fax: 757.857.0523 Email admin@cirsinc.com www .cirsinc .com Technical Assistance 1.800.617.1177 ©2019 Computerized Imaging Reference Systems, Inc. All rights Computerized Imaging Reference Systems, Inc. has reserved.
Need help?
Do you have a question about the QA Phantom 008Z and is the answer not in the manual?
Questions and answers