All information contained in this manual, including all photographs, illustrations and software, is protected under international copyright laws, with all
rights reserved. No part of this manual may be reproduced, copied, translated or transmitted in any form or by any means without the prior written
consent from Panel S.r.l. The information contained herein is believed to be accurate as of the date of publication; however, Panel S.r.l, makes no
warranty, ex- pressed or implied, with regard to the products or documentation contained within this manual. Panel S.r.l. reserves the right to change
the contents of this manual without notice. Panel shall not be liable for direct, indirect, special, incidental, or consequential damages arising out of the
use of any product, nor for any infringements upon the rights of third parties, which may result from such use. Any implied warranties of
merchantability or fitness for any particular purpose is also disclaimed. Soft- ware names, hardware names and trademarks are registered by their
Page 1
No part of this manual may be reproduced, copied, translated or transmitted in any form or by any means without the prior written consent from Panel S.r.l. The information contained herein is believed to be accurate as of the date of publication; however, Panel S.r.l, makes no warranty, ex- pressed or implied, with regard to the products or documentation contained within this manual.
1.1 Safety rules All the Panel PC PSR108 series have been designed and built taking into account all the issues associated with an industrial environment such as that where it is necessary to ensure the operation of the system in the presence of vibration, moisture, dust and critical heat conditions.
The following items are included in the PSR108 unit’s package. Before using the PSR108, please check all the items match the manual list. PSR108 DC power supply Qty 1 Panel PC Qty 1 Quick guide Qty 1 Connector DC supply 1.4 Declaration of conformity...
2 years, beginning on the date of invoice by Panel. PANEL will engage to repair or eventually replace, at its discretion, the whole device or its components, which show construction defects or malfunction if these are pointed out in writing during the warranty period.
Panel PC fanless extremely compact. The PSR108-FM is provided with Intel® Bay Trail Celeron Quad Core 2.0 GHz CPU. The aluminium anodized IP66 front panel is supplied with 5 wire resistive touch screen. 2.2 Products specifications Models PSR108 Technology construction...
High temperature / Humidity: 70°C / 90% RH, 500 hrs, normal environment for 4 hrs High temperature: 70°C / 500 hrs allow panel stays in normal environment for 4 hrs Low temperature: -40°C / 500 hrs allow panel stays in normal environment for 4 hrs Thermal Cycle: -40°C ~ 70℃...
2.5 Mechanical dimensions PSR108 display units with retaining clips All dimensions are specified in mm Display size Model 8.0” single touch resistive PSR108 www.panel.it...
2.6 Mechanical cut-out All dimensions are specified in mm The cut-out tolerance values are +1 mm / -1 mm Display size Model Zmin Zmax Number of retaining clips 8.0” single touch resistive PSR108 ---- www.panel.it...
2.7 Chemical and solvent resistance Aluminum panel overlay The panel overlay withstands 24 hours exposure to the following reagents at 50 °C without visible staining 1.1.1. Trichloroethane Ethylacetate Perchloroethylene Aliphatic hydrocarbons Fluorochlorohydrocarbons Toluene Benzene Glycerine Triacetin Cyclohexanol Glycol Trichloroethylene Diethyl ether...
Page 12
Artificial Perspiration 100.0 (JIS K6772) Optional graphic customization The graphic painted customization is not resistant to the following chemicals: Concentrated mineral acids Concentrated caustic solution High pressure steam at over 100 °C Benzyl alcohol Methylene chloride www.panel.it...
30° When installing the PSR108 in a slanted panel, and the panel face inclines more than 30°, the surrounding air temperature must not exceed 40°C. You may need to use forced air cooling (fan, A/C) to ensure the surrounding air temperature is 40°C or below.
3.3 Fasten PSR108 Insert the PSR108 into the panel cut. When inserted, fix the Panel PC as shown: (1) Turn the clamping levers to the right side through 90°. (2) Tighten the screws without forcing the clamping to avoid the panel bending.
Verify the correct rated input 24 VDC, input voltage limits 9…..36 VDC. The DC power cable must be secured in the terminal block (power connector) as shown in the image. Wires with a cross section of 0.75 mm to 2.5 mm www.panel.it...
To avoid excess noise, make the power cord as short as possible. This section describes the precautions for grounding the PSR108 unit: Exclusive grounding (BEST) Exclusive grounding (OK) Common grounding (NOT OK) Important! The motherboard ground and others devices is connected with PSR108 ground. www.panel.it...
Chapter 4: Hardware upgrade 4.1 Removing the rear cover Warning! Disconnect the power supply to the Panel PC (disconnect the power cable). Isolate the system from all potential sources of electrical power!. Discharge any electrostatic charge on the ground connection...
Firmly insert the SO-DIMM into the slot until the retaining clips at both ends fully snap back in place and the SO-DIMM is properly seated. 4.3 HDD-SSD installation SATA SSD installation area Unscrew the three screws marked above then unplug the two SATA cables. On the rear of the drive bay there are further four screws that lock the SSD unit. www.panel.it...
3) Remove the bracket facing the slot that you intend to use. Keep the screws for later use. 4) Align the card connector with the slot and press firmly until the card is completely seated on the slot. 5) Fasten the card to the chassis with screws. 6) Replace the system cover www.panel.it...
4) Align the card connector with the slot and press firmly until the card is completely seated on the slot. 5) Fasten the card to the chassis with screws. 6) Connect the antenna cable to the main connector of the device: 7) Replace the system cover www.panel.it...
C – Audio Output K – RS232/422/485 (COM 1) D – 2x USB 3.0 L – RS232 (COM 2) E – Gigabit LAN 2 M – USB 2.0 F – Gigabit LAN 1 N – USB 2.0 G – VGA www.panel.it...
Please be noted that the password, date, time, user default profile and MAC address will be cleared only if the CMOS battery is removed. Default PSR108-FM factory setting: 1-2 www.panel.it...
The system is delivered with the optimized defaults preconfigured state and is operational. Changes in the BIOS settings may only be implemented by appropriately trained staff. 6.3 Touchscreen driver and calibration PSR108 touch screen devices are already calibrated by factory. No calibration is needed. www.panel.it...
Best Management Practices (BMP). When you discard the Lithium battery in California, USA and the rest of the world, please follow the related regulations in advance. 7.3 Spare parts It is recommended to install only original Panel spare parts. If the customer mount not original spare parts, we can’t grant the correct work of the device. www.panel.it...