Table of Contents
Advertisement
Quick Links
Panel PC PSR1-EP series
Intel® Core™ i3, i5, i7
Resistive touchscreen
User's manual
Version 1.1
All information contained in this manual, including all photographs, illustrations and software, is protected under international copyright laws, with all
rights reserved. No part of this manual may be reproduced, copied, translated or transmitted in any form or by any means without the prior written
consent from Panel S.r.l. The information contained herein is believed to be accurate as of the date of publication; however, Panel S.r.l, makes no
warranty, ex- pressed or implied, with regard to the products or documentation contained within this manual. Panel S.r.l. reserves the right to change
the contents of this manual without notice. Panel shall not be liable for direct, indirect, special, incidental, or consequential damages arising out of the
use of any product, nor for any infringements upon the rights of third parties, which may result from such use. Any implied warranties of
merchantability or fitness for any particular purpose is also disclaimed. Soft- ware names, hardware names and trademarks are registered by their
respective companies.
www.panel.it
1
1
Advertisement
Table of Contents
Related Manuals for panel PC PSR1-EP Series
Summary of Contents for panel PC PSR1-EP Series
- Page 1 No part of this manual may be reproduced, copied, translated or transmitted in any form or by any means without the prior written consent from Panel S.r.l. The information contained herein is believed to be accurate as of the date of publication; however, Panel S.r.l, makes no warranty, ex- pressed or implied, with regard to the products or documentation contained within this manual.
-
Page 2: Table Of Contents
4.3 HDD-SSD installation ..................18 4.4 Mini PCI-E and mSATA module installation ..........19 4.5 WI-FI module installation ................... 20 Chapter 5: Jumpers and connectors 5.1 Motherboard layout…………………………………………………………………………. 21 5.2 PSR1 I/O connectors ................... 23 5.3 Motherboard jumpers setup ................24 www.panel.it... - Page 3 Chapter 6: System setup 6.1 Installing operating system ................25 6.2 Bios setup ........................25 6.3 Touchscreen driver and calibration ............25 Chapter 7: Maintenance 7.1 Cleaning........................26 7.2 Lithium battery ......................26 7.3 Spare parts ....................... 26 www.panel.it...
-
Page 4: Safety Rules
1.1 Safety rules All the Panel PC PSR1 series have been designed and built taking into account all the issues associated with an industrial environment such as that where it is necessary to ensure the operation of the system in the presence of vibration, moisture, dust and critical heat conditions. -
Page 5: Package Content
The following items are included in the PSR1 unit’s package. Before using the PSR1, please check all the items match the manual list. PSR112/122 AC power supply PSR112/122 DC power supply Qty 1 Panel PC Qty 1 Panel PC Qty 1 Quick guide Qty 1 Quick guide Qty 1 Power cable (IT) 1.8m... -
Page 6: Warranty And Rma
2 years, beginning on the date of invoice by Panel. PANEL will engage to repair or eventually replace, at its discretion, the whole device or its components, which show construction defects or malfunction if these are pointed out in writing during the warranty period. -
Page 7: Chapter 2: Technical Data
Chapter 2: Technical data 2.1 Introduction Panel PC fanless extremely compact. The PSR1-EP is provided with Intel® Core™ i3, i5, i7 CPU. The aluminium anodized IP66 front panel is supplied with 5 wire resistive touch screen 2.2 Products specifications Models PSR112 PSR115... -
Page 8: Touchscreen Specifications
High temperature / Humidity: 70°C / 90% RH, 500 hrs, normal environment for 4 hrs High temperature: 70°C / 500 hrs allow panel stays in normal environment for 4 hrs Low temperature: -40°C / 500 hrs allow panel stays in normal environment for 4 hrs Thermal Cycle: -40°C ~ 70℃... -
Page 9: Mechanical Dimensions
12.1” single touch resistive PSR112 15.0” single touch resistive PSR115 32.5 15.6” single touch resistive PSR116 52.5 17.0” single touch resistive PSR117 18.5” single touch resistive PSR118 87.5 19.0” single touch resistive PSR119 82,5 21.5” single touch resistive PSR122 www.panel.it... -
Page 10: Mechanical Cut-Out
Number of retaining clips 12.1” single touch resistive PSR112 15.0” single touch resistive PSR115 15.6” single touch resistive PSR116 17.0” single touch resistive PSR117 18.5” single touch resistive PSR118 19.0” single touch resistive PSR119 21.5” single touch resistive PSR122 www.panel.it... -
Page 11: Chemicals And Solvents Resistance
2.7 Chemical and solvent resistance Aluminum panel overlay The panel overlay withstands 24 hours exposure to the following reagents at 50 °C without visible staining 1.1.1. Trichloroethane Ethylacetate Perchloroethylene Aliphatic hydrocarbons Fluorochlorohydrocarbons Toluene Benzene Glycerine Triacetin Cyclohexanol Glycol Trichloroethylene Diethyl ether... - Page 12 Artificial Perspiration 100.0 (JIS K6772) Optional graphic customization The graphic painted customization is not resistant to the following chemicals: Concentrated mineral acids Concentrated caustic solution High pressure steam at over 100 °C Benzyl alcohol Methylene chloride www.panel.it...
-
Page 13: Chapter 3: Installation And Wiring
30° When installing the PSR1 in a slanted panel, and the panel face inclines more than 30°, the surrounding air temperature must not exceed 40°C. You may need to use forced air cooling (fan, A/C) to ensure the surrounding air temperature is 40°C or below. -
Page 14: Fasten Psr1
3.3 Fasten PSR1 Insert the PSR1 into the panel cut. When inserted, fix the Panel PC as shown: (1) Insert each of the fasteners, as shown. (2) Be sure to pull the fastener back until it is flush with the rear of the attachment hole. -
Page 15: Connecting Dc Power
All supplied power must be disconnected before removing device covers or components or installing/removing accessories, hardware or cables. The power cable must be disconnected from the device and from the voltage supply. Verify the correct rated input 110 - 230 VAC, input voltage limits 90…..264 VAC. www.panel.it... -
Page 16: Functional Ground
To avoid excess noise, make the power cord as short as possible. This section describes the precautions for grounding the PSR1 unit: Exclusive grounding (BEST) Exclusive grounding (OK) Common grounding (NOT OK) Important! The motherboard ground and others devices is connected with PSR1 ground. www.panel.it... -
Page 17: Chapter 4: Hardware Upgrade
Chapter 4: Hardware upgrade 4.1 Removing the rear cover Warning! Disconnect the power supply to the Panel PC (disconnect the power cable). Isolate the system from all potential sources of electrical power!. Discharge any electrostatic charge on the ground connection... -
Page 18: Hdd-Ssd Installation
Firmly insert the SO-DIMM into the slot until the retaining clips at both ends fully snap back in place and the SO-DIMM is properly seated. 4.3 HDD-SSD installation Unplug the two SATA cables. Then, SATA SSD installation area unscrew the two screws marked above. On the sides of the drive bay there are two more screws that lock the SSD unit www.panel.it... -
Page 19: Mini Pci-E And Msata Module Installation
3) Remove the bracket facing the slot that you intend to use. Keep the screws for later use. 4) Align the card connector with the slot and press firmly until the card is completely seated on the slot. 5) Fasten the card to the chassis with screws. 6) Replace the system cover www.panel.it... -
Page 20: Wi-Fi Module Installation
4) Align the card connector with the slot and press firmly until the card is completely seated on the slot. 5) Fasten the card to the chassis with screws. 6) Connect the antenna cable to the main connector of the device: 7) Replace the system cover www.panel.it... -
Page 21: Chapter 5: Jumpers And Connectors
Chapter 5: jumpers and connectors 5.1 Motherboard IMB-191 layout www.panel.it... - Page 22 13 : Digital Input / Output Power Select (JGPIO_PWR1) 14 : Digital Input / Output Default Value Setting (JGPIO_SET1) 15* : LVDS Panel Connector (Only for IMB-190 / IMB-191) * eDP Connector (on the Backside of PCB) (Only for IMB-190-E)
-
Page 23: Psr1 I/O Connectors
P – 2x USB 3.0 F – RS232 (COM 3) Q – Gigabit LAN 3 (optional) G – RS232 (COM 4) R – Supply Connector H – Audio Output T – WI-FI Antenna (optional) J – Mic-in K – Gigabit LAN 2 www.panel.it... -
Page 24: Motherboard Jumpers Setup
Please be noted that the password, date, time, user default profile and MAC address will be cleared only if the CMOS battery is removed. Default PSR1 factory setting: 1-2 www.panel.it... -
Page 25: Chapter 6: System Setup
The system is delivered with the optimized defaults preconfigured state and is operational. Changes in the BIOS settings may only be implemented by appropriately trained staff. 6.3 Touchscreen driver and calibration PSR1 touch screen devices are already calibrated by factory. No calibration is needed. www.panel.it... -
Page 26: Chapter 7: Maintenance
Best Management Practices (BMP). When you discard the Lithium battery in California, USA and the rest of the world, please follow the related regulations in advance. 7.3 Spare parts It is recommended to install only original Panel spare parts. If the customer mount not original spare parts, we can’t grant the correct work of the device. www.panel.it...