Table of Contents
Advertisement
Quick Links
Great care has gone into the manufacture of this product and it should
therefore provide you with years of good service when used properly. In
the event of product failure within its intended use over the course of the
first 3 years after date of purchase, we will remedy the problem as quickly
as possible once it has been brought to our attention. In the unlikely event
of such an occurrence, or if you require any information about the product,
please contact us via our helpline support services, details of which are to be
found both in this manual and on the product itself.
GB
IE
PRODUCED IN CHINA FOR:
ALDI STORES LTD. PO BOX 26, ATHERSTONE
WARWICKSHIRE, CV9 2SH.
ALDI STORES (IRELAND) LTD.
PO BOX 726, NAAS, CO. KILDARE.
Visit us at www.aldi.com
AFTER SALES SUPPORT
+44(0) 1904727501
+353(0) 019022605
GB
IE
support@coreservice.co.uk
MODEL:
Z1G-DS-65H
3
802984
YEAR
WARRANTY
01/2021
User Manual
DEMOLITION BREAKER
Original User Manual
Advertisement
Table of Contents
Related Manuals for FERREX Z1G-DS-65H
Summary of Contents for FERREX Z1G-DS-65H
- Page 1 ALDI STORES LTD. PO BOX 26, ATHERSTONE WARWICKSHIRE, CV9 2SH. ALDI STORES (IRELAND) LTD. PO BOX 726, NAAS, CO. KILDARE. Visit us at www.aldi.com AFTER SALES SUPPORT 802984 +44(0) 1904727501 +353(0) 019022605 support@coreservice.co.uk YEAR MODEL: WARRANTY Z1G-DS-65H 01/2021 Original User Manual...
-
Page 2: Overview
Overview... - Page 3 Overview...
-
Page 4: Scope Of Delivery/Device Components
Scope of delivery/device components Scope of delivery/device components Demolition breaker Flat bit Pointed bit 3 mm Allen key Carbon brushes (2x) Grease cap Lock switch Main switch Main handle Blow count selector Extra handle Extra handle locking screw Bit adjusting sleeve Bit locking sleeve Bit holder Tool case (not illustrated) -
Page 5: Table Of Contents
Table of content Table of content Overview........................2 Scope of delivery/device components..............4 General information....................6 Reading and storing the operating manual..............6 Proper use....................... 6 Residual risks........................6 Explanation of symbols................... 7 Safety........................8 Safety notes........................8 General safety notes for power tools................8 Before first use....................... -
Page 6: General Information
General information General information Reading and storing the operating manual This operating manual is part of the demolition breaker (hereinafter also called "device"). It contains important information on how to set up and use the product. Before using the device, read the operating manual carefully, in particular the safety instructions. -
Page 7: Explanation Of Symbols
Explanation of symbols Explanation of symbols The following symbols and signal words are used in this user manual, on the device or on the packaging. This symbol provides you with useful additional information on handling and use. Declaration of conformity (see chapter “Declaration of conformity”): Products marked with this symbol meet all the applicable Community regulations of the European Economic Area. -
Page 8: Safety
Explanation of symbols Wear protective gloves. Safety The following signal words are used in this operating manual. This signal symbol/word denotes a WARNING! hazard with an average risk level that could lead to death or severe injury if it is not avoided. This signal symbol/word denotes a CAUTION! hazard with a low risk level that could... - Page 9 Safety Workplace safety Clutter or unlit work - Keep your work area tidy and well lit. areas can lead to accidents. - Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or Power tools create sparks which may ignite the dust or dust.
- Page 10 Safety Damaged or tangled cables edges and moving parts. increase the risk of electric shock. - When using a power tool outdoors, use an extension cable Damaged or tangled cables that is suitable for outdoor use. increase the risk of electric shock. - If you must use a power tool in a damp environment, use a power source that is protected by a residual current Using trip switches reduces the risk of...
- Page 11 Safety - Dress properly. Do not wear loose clothing or jewellery. Keep your hair and clothing away from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts. - If devices are provided for the connection of dust extraction and collection facilities, ensure these are Use of dust collection can connected and properly used.
- Page 12 Safety properly without jamming, and whether parts are broken or damaged to such an extent that they impair the functions of the power tool. Have damaged parts repaired Many accidents happen due to before using the power tool. poorly maintained power tools. Carefully maintained - Keep cutting tools sharp and clean.
-
Page 13: Before First Use
Safety - Do not let inexperienced persons use the device and its accessories. - Persons with physical or mental impairments must not use the device and its accessories unsupervised. - Children must not play with, clean or service the device and its accessories. -
Page 14: Selecting The Right Bit
Operation Selecting the right bit Pointed bit We recommend using the pointed bit when working on hard materials such as concrete. It concentrates the whole blow energy on one point. The resulting wedge effect ensures the highest demolition rate. Flat bit You can use the flat bit to "mark"... -
Page 15: Setting The Bit Position
Operation Setting the bit position 1. Set the device down on a non-slip surface with the bit holder and already inserted flat bit pointing up. 2. Pull up the bit adjusting sleeve with one hand. 3. Turn the bit adjusting sleeve to the desired position. 4. -
Page 16: Adjusting The Extra Handle
Operation Adjusting the extra handle 1. Undo the extra handle locking screw by turning it counter-clockwise. 2. Move the extra handle into the desired position. 3. Tighten the extra handle locking screw again by turning it clockwise. The extra handle has been set to the desired position. Presetting the blow count... -
Page 17: Turning The Device On And Off
Operation 1. Turn off the device and wait until it has completely stopped moving. 2. By turning the blow count selector , set the blow count to a value between 1 and 6 (1 - lowest blow count, 6 - highest blow count, for values see "Technical data"). -
Page 18: Removing The Bit
Operation Removing the bit CAUTION! Risk of injury! The bit can become very hot during use. - Let the bit cool down and wear gloves to remove the bit or adjust the bit position. 1. Set the device down on a non-slip surface with the bit holder pointing up. -
Page 19: Handling The Device
Handling the device Handling the device CAUTION! Risk of injury through excess pressure on the device! - Do not exert any excess pressure on the device during operation as this may cause a strong resistance force on the hand grips. CAUTION! Risk of injury! Working with the device can cause a lot of dust and noise. - Page 20 Working in vertical position Grip the main handle with both hands. The integrated vibration damper reduces the vibrations and thus also signs of fatigue that occur when working with the device. The ergonomically shaped handle made of non-slip material ensures better grip on the device and facilitates handling.
-
Page 21: Cleaning And Maintenance
Cleaning and maintenance Cleaning and maintenance CAUTION! Risk of injury! - Switch the device off, disconnect it from the power supply and let it cool down before working on it. Cleaning - Clean the housing with a soft, slightly damp cloth. - Clean the bit after use with a damp cloth and dry it off afterwards. -
Page 22: Storage
Inspection Do not operate a damaged device or accessory. Have the damaged device or accessory checked and repaired by an authorised service centre. Storage NOTE! Risk of damage! Improper storage of the device can result in damage. - Allow the device to completely cool down. - Place the device so that it can’t fall into water. -
Page 23: Troubleshooting
Troubleshooting Troubleshooting Problem Possible cause Fault rectification The bit drops out. The bit holder does Slide the bit into not lock. the bit holder again (see "Inserting the bit") The device cannot be The device is not Check the cables, plugs switched on. -
Page 24: Technical Data
Technical data Technical data Model Z1G-DS-65H Weight 11.7 kg Dimensions (W x H x D) approx. 65 x 12.5 x 27 cm Item number 802984 Rated power 1,700 W Rated voltage 230 V ～ (50 Hz) Blow count 200 - 2,100 blows/min... -
Page 25: Noise/Vibration Information
Technical data Noise/vibration information Warning! The vibration and noise emissions can deviate from the stated values during actual use of the power tool. This depends on the way the power tool is actually used and especially on the type of workpiece you are working on. It is necessary to establish safety measures that protect the operator based on an estimate of the exposure during actual conditions of use (taking into account all parts of the operating cycle, such as periods when the power tool is switched off and... -
Page 26: Declaration Of Conformity
Declaration of conformity EC Declaration of Conformity MEROTEC GmbH Otto-Brenner-Str. 8, 47877 Willich, Germany herewith declare that our product Demolition Breaker Model No. Z1G-DS-65H is in conformity with the following directives: 2006/42/EC Machinery Directive 2014/30/EU EMC directive 2000/14/EC Noise Directive, amended by 2005/88/EC...
Need help?
Do you have a question about the Z1G-DS-65H and is the answer not in the manual?
Questions and answers