1. Manuals
  2. Brands
  3. DevilsOwn Manuals
  4. Engine
  5. Alcohol Injection System
  6. Manual

DevilsOwn Alcohol Injection System Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Stage 1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Alcohol Injection System and is the answer not in the manual?

Questions and answers

Summary of Contents for DevilsOwn Alcohol Injection System

  • Page 1 Stage 1...
  • Page 2 The DevilsOwn™ Alcohol Injection System begins with a connection to a supply tank containing a methanol/water mixture. We recommend DevilsOwn Brew for use with our products. This mixture is pumped at high pressure through the tubing to the nozzle holder. The amount of alcohol and water that is injected through the nozzle is easily adjusted by means of metering the nozzle.
  • Page 3 Intermittent wiring problems, etc., can lead to erratic system performance and possible engine damage. DO NOT use Teflon sealing tape on any fittings in a DevilsOwn™ Alcohol Injection System. It is easy for Teflon tape to get pulled into the system causing blockages that can ultimately lead to incorrect alcohol system performance and potentially engine damage.
  • Page 4 Optional Fluid Level Switch ❑ Drill 7/8" hole in fluid tank, 1-3/4" from bottom of tank ❑ Place switch inside tank and screw in place ❑ Run one wire to chassis ground ❑ Run other wire to LED or buzzer DevilsOwn Injection...

  • Page 5: Section 1: Fluid Bottle

    Regardless of where the tank is mounted (under hood, in trunk, etc.), we recommend mounting the pump near the tank. DevilsOwn pumps are pusher type pumps and they work best when placed as close to the tank as possible.

  • Page 6: Section 2: Pump Installation

    Section 2: Pump Installation Figure 2: Pump placement The DevilsOwn pump should be mounted below and as close to the reservoir (tank) as possible using four of the #10 × 1½" screws. Make sure to mount the pump away from heat, moisture and road debris.

  • Page 7: Section 3: Nozzle Selection

    1. Adjust the start position to inject at a higher boost level. 2. Adjust the full position to inject at a higher boost level. 3. Use a smaller injection nozzle. Correctly Installed Incorrectly Installed Figure 3: Nozzle mounted into nozzle holder DevilsOwn Injection...

  • Page 8: Section 4: Nozzle Installation

    Section 4: Nozzle Installation DevilsOwn strongly advises placing the nozzle AFTER the Mass Air sensor and/or an air-to-air intercooler if so equipped and if possible. On most turbocharged or CSC applications, DevilsOwn users place the nozzle in the outlet of the intercooler. If no intercooler is present, the nozzle can be placed in any accessible location before the throttle body.

  • Page 9: Section 5: Tubing

    Slide the tubing into the push-to-connect on the pump and then into the tank. With the push-to-connect used on the DevilsOwn pumps, the tubing can be easily removed by pressing in on the sleeve and lightly pulling on the tubing.

  • Page 10: Section 6: Devilsown Stage 1Kit

    Section 6: DevilsOwn Stage 1Kit Figure 4: Kit Wiring Diagram Wire Connections: Figure 5 (courtesy Posi- Tap) Shows instructions on how to use the Posi- Tap connecters that are included with this system. DevilsOwn Injection...
  • Page 11 PSI, turn to the right. To lower the turn on PSI, turn to the left. As a general starting point, start off with the top of the wheel adjusted to ½ of your max boost. Lower or rise as necessary. DevilsOwn Injection...

  • Page 12: Section 7: Optional Parts

    Cut your tubing and place it inline. Fluid can travel thru it in any direction. Nozzle Mounting Adapter (optional) Drill a 9/16" hole in your intake tube. Pop it in and tighten. Has an integrated O ring to eliminate boost leaks. DevilsOwn Injection...
  • Page 13 200PSI. To increase pump pressure to 250PSI, turn the allen screw a quarter of a turn to the right. To decrease pressure to 150PSI, turn the allen screw a quarter of a turn to the left. Special Notice DevilsOwn Injection...
  • Page 14 DevilsOwn reserves the right to, at any time or without prior notification or liability, change or improve the design of any product, add products or discontinue products. Any such acts will not give rise to an obligation to accept returns of (except those returns specifically provided for herein) or to update the design of any such prior products.
  • Page 15 Updated 12/31/2009 DevilsOwn Injection...

Table of Contents