ARGENTO PIUMA-S User Manual

Epac bicycle, electric pedal-assisted cycle
Hide thumbs Also See for PIUMA-S:

Advertisement

ELECTRIC BICYCLE WITH
ELECTRIC BICYCLE WITH
PEDALING ASSISTANCE SYSTEM
PEDALING ASSISTANCE SYSTEM
ELECTRIC PEDAL-ASSISTED CYCLE
EPAC BICYCLE –
For information, technical support and assistance, visit www.argentobike.it
EPAC BICYCLE
Electric pedal-assisted cycle
USER MANUAL
PIUMA-S

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the PIUMA-S and is the answer not in the manual?

Questions and answers

Summary of Contents for ARGENTO PIUMA-S

  • Page 1 ELECTRIC BICYCLE WITH ELECTRIC BICYCLE WITH PEDALING ASSISTANCE SYSTEM EPAC BICYCLE PEDALING ASSISTANCE SYSTEM ELECTRIC PEDAL-ASSISTED CYCLE EPAC BICYCLE – Electric pedal-assisted cycle USER MANUAL PIUMA-S For information, technical support and assistance, visit www.argentobike.it...
  • Page 3: Table Of Contents

    HARGING THE BATTERY ...................... 11 ONTROL DEVICES ........................11 HEELS ......................11 RAKING SYSTEM ........................12 SSEMBLY PIUMA-S ..................12 MODEL ASSEMBLY ................13 AXIMUM LIMIT OF THE SEAT POST ..............14 AINTENANCE INSTRUCTIONS AND ROADING ........................14 LEANING ....................14 HAIN LUBRIFICATION ....................
  • Page 4: Foreword

    1.2 Assistance Service For any inconvenience or request for clarification, contact without hesitation the Assistance Service of your authorized ARGENTO dealer, who has competent and specialized staff, specific equipment and original spare parts. 1.3 Graphical form of safety warnings To identify the safety messages in this manual, the following graphic warning symbols will be used.
  • Page 5: Safety Warnings

    For any data not included or not deducible from this manual, it is recommended to consult directly the Assistance Service of your authorized ARGENTO dealer. 2.3 Warnings for users - It is forbidden to load a passenger.
  • Page 6: Maintenance Warnings

    Original spare parts Use only original ARGENTO spare parts. Any liability of the manufacturer for damage or loss of functionality caused as a result of using non-original accessories and parts is excluded.
  • Page 7: Description Of The Bicycle (Epac)

    3. DESCRIPTION OF THE BICYCLE (EPAC) 3.1 Parts list 1. R EAR LIGHT ARRIER 3. B SAMSUNG 36V ATTERY 4. S 5. F RAME FOLDING DEVICE 6. S 7. D ISPLAY 8. S SHIMANO HIFTER 9. B RAKE LEVER 10. F RONT LIGHT 11.
  • Page 8: Terms Of Use

    3.2 Terms of use The pedal-assisted bicycle was designed and built to be driven outdoors, on public roads and on cycle paths, but always on asphalted surfaces. Any modification of the state of construction can compromise the behavior, safety and stability of the pedal-assisted bicycle and can lead to an accident. Other types of use, or the extension of use beyond that envisaged, do not correspond to the destination assigned by the manufacturer, and therefore the manufacturer cannot accept any responsibility for any resulting damage.
  • Page 9: Lifting And Transport

    Striclty forbidden actions Ride the pedal-assisted bicycle for uses other than those for which it was built, i.e. a passenger's pleasure craft. Ride your pedal-assisted bicycle in areas where there is a danger of explosions. Ride your pedal-assisted bicycle in adverse weather conditions (pouring rain, hail, snow, strong wind, etc.).
  • Page 10: Commissioning

    5. COMMISSIONING 5.1 Charging the battery Before using the bicycle for the first time, it is necessary to charge the battery for at least 4-6 hours, until charging is complete, using the battery charger supplied. The average charging time is around 4-6 hours. The batteries are of the lithium type 36V.
  • Page 11: Control Devices

    Precautions when charging Always connect the plug to the battery and then the power plug to the mains. When recharging is complete, always disconnect the plug from the mains first and then the plug from the battery. Always recharge the battery completely. Always use original power supplies.
  • Page 12: Assembly

    6. ASSEMBLY 6.1 Piuma-S model assembly 1. Carefully remove the bike from the packaging, then remove all the protective material, being careful not to scratch the painted parts and not to pull the bike cables. The removal of the bike from the packaging must be carried out by two adults, in order not to incur injuries or crushing.
  • Page 13: Maximum Limit Of The Seat Post

    • In the event that, during the assembly, unclear passages or difficulties in the assembly itself should be encountered, DO NOT RIDE THE ASSISTED BIKE. • Contact the Assistance Service of your authorized ARGENTO dealer. 6.2 Maximum limit of the seat post IT IS STRICTLY FORBIDDEN...
  • Page 14: Maintenance Instructions And Roading

    This manual does not include on information regarding disassembly and extraordinary maintenance, since these operations must always be carried out exclusively by the staff of the Assistance Service of your authorized ARGENTO dealer. The Assistance Service is able to provide all the information and to answer all requests to take care of and keep your pedal-assisted bicycle perfectly efficient.
  • Page 15: Checking The Parts

    7.3 Checking the parts The supporting frame of the pedal-assisted bicycle and the welds must be free of visible defects such as: cracks, deformations, incisions, corrosions, etc. Make sure that all the bolts and pedals of the pedal-assisted bicycle are properly tightened.
  • Page 16: Avg Speed - Max Speed - Trip - Odo - Time

    8.4 AVG SPEED – MAX SPEED – TRIP – ODO – TIME Press the ON button to switch between the AVG SPEED - MAX SPEED - TRIP - ODO - TIME function The AVG SPEED function shows the average speed kept during the last use of the bike, the MAX SPEED function shows the maximum speed kept during the last use of the bike, the TRIP function consists in showing the partial Km traveled with your electric bike, the ODO function consists in showing the total Km traveled with your...
  • Page 17: Lcd Configuration

    9. LCD CONFIGURATION Press the M button for at least 2 seconds to enter the LCD display configuration. Within the display configuration, press the + and - buttons to change the value of the single parameter, press the M button to move to the next parameter, press the M button for at least 2 seconds to exit the LCD display configuration.
  • Page 18: Number Of Assistance Levels (Pas)

    9.7 Number of assistance levels (PAS) Indicated by the PA symbol, press the + and - buttons to switch between the selectable values UBE - 3 - 5 - 9. Do not select the UBE value (manufacturer's test value) in order not to find anomalies on your display and compromise the normal operation of your electric bike.
  • Page 19: Connection Diagram

    11. CONNECTION DIAGRAM...
  • Page 20 DISTRIBUTED BY:...

Table of Contents