Advertisement
Quick Links
Rev
01
02
Confidential: Property of Verus Engineering. Not for Distribution outside intended recipient list.
Verus Engineering
sales@verus-engineering.com
ZN6 / ZC6 Two-Piece Splitter
Release Date: 2017/01/25
Approvals: E. Hazen, P. Lucas
Document Revisions
Date
Author
2016/09/23
E.Hazen
2017/08/08
P. Lucas
Install Manual
Author: Eric Hazen
Initial release of install manual
Company name change from Velox to Verus
Description
Advertisement
Related Manuals for Verus Engineering ZN6
Summary of Contents for Verus Engineering ZN6
- Page 1 Approvals: E. Hazen, P. Lucas Document Revisions Date Author Description 2016/09/23 E.Hazen Initial release of install manual 2017/08/08 P. Lucas Company name change from Velox to Verus Confidential: Property of Verus Engineering. Not for Distribution outside intended recipient list. Verus Engineering sales@verus-engineering.com...
- Page 2 1.4. Tools Needed ..........................<3> 1.5. Splitter Components ....................... <3-4> 2. Front Splitter Prep .......................... <5-6> 3. Front Splitter Install ........................<6-10> 4. Support Rod Install ........................<10-17> Confidential: Property of Verus Engineering. Not for Distribution outside intended recipient list. Verus Engineering sales@verus-engineering.com 3/6/2016...
- Page 3 1.6.4. (1) Support Brace 1.6.5. (1) Two Piece Splitter Bracket 1.6.6. Hardware Bags 1.6.6.1. (8) M6 x 18mm Diameter Washer 1.6.6.2. (12) M6 x 1.0 Flanged Nut Confidential: Property of Verus Engineering. Not for Distribution outside intended recipient list. Verus Engineering sales@verus-engineering.com 3/6/2016...
- Page 4 (4) M6 x 12mm Diameter Washer 1.6.6.4. (6) M6 x 1.0 BHCS x 25mm Long 1.6.6.5. (8) M6 x 1.0 BHCS x 16mm Long Confidential: Property of Verus Engineering. Not for Distribution outside intended recipient list. Verus Engineering sales@verus-engineering.com 3/6/2016...
- Page 5 2.4. Align the splitter support bracket as shown below and using a center punch mark (3) holes on each splitter half. 2.5. With the (6) holes center punches, drill through these holes with a 1/4” drill bit. Confidential: Property of Verus Engineering. Not for Distribution outside intended recipient list. Verus Engineering sales@verus-engineering.com...
- Page 6 This piece is quite large and has multiple plastic push rivets and a few bolts holding it on. There will be six push pins (shown in red), and three 10mm bolts to remove (shown in yellow). Confidential: Property of Verus Engineering. Not for Distribution outside intended recipient list. Verus Engineering sales@verus-engineering.com...
- Page 7 Note, the backing washer is not necessary but will decrease the chance that the rivet gets pulled through the bumper. Confidential: Property of Verus Engineering. Not for Distribution outside intended recipient list. Verus Engineering sales@verus-engineering.com...
- Page 8 3.8. Below are pictures of a properly installed rivet nut. We did not use the backing washers here though feel free to if you would like, they are supplied with each kit. Confidential: Property of Verus Engineering. Not for Distribution outside intended recipient list. Verus Engineering sales@verus-engineering.com...
- Page 9 We suggest to leave all bolts loose until they are all in and then tighten from the inside out. We also suggest you have the splitter held up by 4 or more bolts before letting the splitter free hang. Confidential: Property of Verus Engineering. Not for Distribution outside intended recipient list. Verus Engineering sales@verus-engineering.com...
- Page 10 4.3. To remove the front bumper, remove the strip of 10mm bolts and plastic push pins across the top of the front bumper under the hood. Confidential: Property of Verus Engineering. Not for Distribution outside intended recipient list. Verus Engineering sales@verus-engineering.com...
- Page 11 The arrow in the picture shows this well. I used a flat head screwdriver to push this forward and then gently pried the signal away from the car. Confidential: Property of Verus Engineering. Not for Distribution outside intended recipient list. Verus Engineering sales@verus-engineering.com...
- Page 12 4 raised portions, using the brackets to ensure that you can bolt them on the crash beam in the location necessary for a proper install with the grill. Confidential: Property of Verus Engineering. Not for Distribution outside intended recipient list. Verus Engineering sales@verus-engineering.com...
- Page 13 Once you ensure the holes were drilled properly, remove the brackets and reinstall the bumper in reverse order Confidential: Property of Verus Engineering. Not for Distribution outside intended recipient list. Verus Engineering sales@verus-engineering.com...
- Page 14 Below is both a BRZ and an FRS install (note BRZ install has our old, obsolete rod end design). Confidential: Property of Verus Engineering. Not for Distribution outside intended recipient list. Verus Engineering sales@verus-engineering.com...
- Page 15 With the splitter fully installed, we can make the holes for the clevis to bolt to. 4.14. Place the lower aluminum plate underneath the splitter, roughly centered, and mark the center of the two slots as shown below. Confidential: Property of Verus Engineering. Not for Distribution outside intended recipient list. Verus Engineering sales@verus-engineering.com 3/6/2016...
- Page 16 200 lbs of downforce at this point. It is not wise to stand on the splitter, it can handle this load but the aluminum bracket beneath can bend and lead to distortion. Confidential: Property of Verus Engineering. Not for Distribution outside intended recipient list. Verus Engineering sales@verus-engineering.com...
- Page 17 ZC6 / ZN6 Two Piece Front Splitter – Install Manual 4.21. Please contact Verus Engineering with any questions, comments, concerns, and feedback via sales@verus-engineering.com. Confidential: Property of Verus Engineering. Not for Distribution outside intended recipient list. Verus Engineering sales@verus-engineering.com 3/6/2016...
Need help?
Do you have a question about the ZN6 and is the answer not in the manual?
Questions and answers