Time-Setting Options - Siemens CM778GN.1B User Manual And Installation Instructions

Table of Contents

Advertisement

10  Time-setting options
For an operation, you can set the cooking time and the
time at at which the operation should be ready. The
timer runs independently of the appliance during the
operation.
Time-setting
Use
option
Cooking time
If you set a cooking time, the appli-
ance stops heating automatically
once this time has elapsed.
Ready at
Along with the cooking time, you can
set the time at which you want cook-
ing to end. The appliance starts up
automatically so that it finishes cook-
ing at the required time.
Timer
You can set the timer to run inde-
pendently of the appliance during op-
eration. It does not affect the appli-
ance.
10.1 Setting the cooking time
You can set the cooking time for the operation of up to
24 hours.
Requirement: An operating mode and temperature or
setting have been set.
Press "Cooking time".
1.
To set the cooking time, press the relevant time
2.
value, e.g. hour display "h" or minute display "min."
a The selected value is marked in blue.
Set the cooking time using the adjustment line or
3.
enter it directly via the number field
If required, use
to reset the adjustment value.
Use "Start" to start the operation.
4.
a The appliance starts to heat and the time counts
down.
a Once the cooking time has elapsed, a signal tone
sounds. A note appears on the display confirming
that the operation has finished.
Once the cooking time has elapsed:
5.
If required, you can select other settings and re-
start the operation.
When the food is ready, use
pliance off.
Changing the cooking time
You can change the cooking time at any time.
Press the cooking time.
1.
Change the cooking time using the adjustment line
2.
or enter it directly via the number field
Press "Apply".
3.
Cancelling the cooking time
You can cancel the cooking time at any time.
Press the cooking time.
1.
Reset the cooking time using
2.
Note: For operating modes that always require a
cooking time, the appliance resets the cooking time
to the preset value.
3.
Press "Apply".
⁠ .
to switch the ap-
⁠ .
⁠ .
10.2 Setting "Ready at"
You can delay the time at which the cooking time for
the operation should be ready by up to 24 hours.
Requirements
¡ An operating mode and temperature or setting have
been set.
¡ A cooking time is set.
Press "Ready at".
1.
Delay the time using the adjustment line or directly
2.
via the number field
If required, use
to reset the adjustment value.
Use "Start" to start the operation.
3.
a The display shows the start time. The appliance is in
standby mode.
a Once the start time has been reached, the appli-
ance starts heating and the cooking time starts
counting down.
a Once the cooking time has elapsed, a signal tone
sounds. A note appears on the display confirming
that the operation has finished.
Once the cooking time has elapsed:
4.
If required, you can select other settings and re-
start the operation.
When the food is ready, use
pliance off.
Changing "Ready at"
To achieve good cooking results, only change the set
time before the operation starts and before the cooking
time starts counting down.
Press "Ready at".
1.
Change the time using the adjustment line or enter
2.
it directly via the number field
Press "Apply".
3.
Cancelling "Ready at"
You can delete the set time at any time.
Press "Ready at".
1.
Use
to reset the time.
2.
Note: For operating modes that always require a
cooking time, the appliance resets the time at which
the cooking time ends to the next possible time.
Press "Apply".
3.
10.3 Setting the timer
The timer runs independently during the operation. You
can set the timer when the appliance is switched on or
off, up to 24 hours. The timer has its own signal tone
so that you can tell whether it is the timer or a cooking
time that has elapsed.
Press the
button.
1.
To set the timer, press the relevant time value on
2.
the display, e.g. hour display "h" or minute display
"min".
a The selected value is marked in blue.
Set the timer using the adjustment line or directly via
3.
the number field
⁠ .
If required, use
to reset the adjustment value.
To start the timer, press "Start".
4.
a The timer counts down.
Time-setting options en
⁠ .
to switch the ap-
⁠ .
15

Advertisement

Table of Contents
loading

Table of Contents