Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for 3nStar PTE0605
Summary of Contents for 3nStar PTE0605
- Page 1 All-In-One POS Systems, Intel J6412 USER MANUAL PTE0605...
-
Page 2: Table Of Contents
Chassis Details ........................5 Main Screen Details ....................... 6 Definitions ..........................6 Motherboard ......................... 7 Cables ............................ 8 PTE0605 - J6412 I/O Ports ..................... 9 Take Apart ......................10 Before You Start ........................10 Tools to prepare ........................10 Preparation .......................... 10 Motherboard ........................ -
Page 3: Introduction
Introduction Product Overview Picture-01 1. 15-inch TFT-LCD 2. The host indicator (Blue - system on, green - standby) 3. Base 4. Customer Display 5. Three track MSR with Dallas Lock 6. Three track MSR... -
Page 4: Pos Section
POS Section Views Picture-02... -
Page 5: Internal Quick View
Internal Quick View Picture-03 Chassis Details Picture-04... -
Page 6: Main Screen Details
Main Screen Details Picture-05 Definitions Item Quantity Motherboard Memory Slot 2.5” SATA SSD Slot Cooling System Speaker Touch Control Board LVDS Riser Card Backlight Inverter Host Indicator... -
Page 7: Motherboard
Motherboard Picture-06 Item Quantity Host Indicator Port (Foolproof) Speaker Port (Foolproof) Mini-PCIe Slot (Wi-Fi Module) LVDS, Backlight & Touch Combo Port (Foolproof) Memory Card (DDR4) Slot 2.5” Hard Drive Slot USB Port for Optional Module (Foolproof) -
Page 8: Cables
Cables Picture-07 Item Quantity Speaker Cable (2 in 1) USB Cable (available when connected to MSR) LVDS Cable (3 in 1 Combo Cable) Backlight Cable (3 in 1 Combo Cable) Touch Cable (3 in 1 Combo Cable) Host Indicator Cable... -
Page 9: Pte0605 - J6412 I/O Ports
PTE0605 - J6412 I/O Ports Picture-08 Item Remark Quantity Power Switch Audio Combo Mic-In/Speaker-out (Combo Jack) COM (RJ50) COM1~3: 0/5/12V by pin-JP USB 3.0 Not powered during standby BIOS Reset Button Power enabled by BIOS; +12V 10/100/1000 Mbps USB 2.0... -
Page 10: Take Apart
Take Apart Before You Start 1. Read these instructions completely before you start. 2. Strictly follow all instructions. 3. Pay attention to all warnings. Tools to prepare 1 Screwdriver • Preparation To protect POS Chassis and display, please carefully place the POS terminal on a •... -
Page 11: Motherboard
Motherboard 1. Unscrew and open the I/O panel cover on chassis. Picture-09 Picture-10 2. Disconnect all cables from the I/O Ports Panel. Picture-11 Picture-12... - Page 12 3. Take out the 2.5" Hard Drive from the Hard Drive Slot. Picture-28 Picture-29...
- Page 13 4. Use a HEX screwdriver to remove the hex spacers of the VGA Port and then unscrew the chassis and open it. Picture-13 Picture-14 Picture-15...
- Page 14 5. To replace the motherboard, please disconnect all cables from ports on the motherboard and unscrew six screws on the motherboard edge. Picture-17 6. Since the CPU on the backside of the motherboard connects to the cooling system through silicone, be careful when you unscrew the four screws in the CPU area (You must use a screwdriver by hand rather than an electric screwdriver!).
-
Page 15: Customer Display
Customer Display 1. Unplug the VGA from the I/O Ports Panel. Picture-18 Picture-19... - Page 16 2. Remove the cover on the rear case, adjust the base to be vertical to the Chassis, and unscrew the four screws at the joint. Picture-20 3. Detach the base with the secondary screen from the Chassis. Picture-21...
- Page 17 4. Unscrew four screws and separate the base and the customer display screen. Picture-22 5. Remove the two screws on the back of the customer monitor and open the rear case. Picture-23 6. You will see the board and the cable in customer display. (Please maintain it under the guidance of the technicians of your supplier because usually, users only need to detach the customer display from the POS and send it to your supplier.
-
Page 18: Memory Card
Memory Card 1. Find the memory card slot on the motherboard. Picture-24 Pull out the buckles on both sides with your fingers and take out the ejected memory card. Picture-25 Picture-26... -
Page 19: Hard Drive
Hard Drive 1. Find the hard drive slot on the right side of back chassis. Picture-27 2. Unscrew two screws on the cover and open it. Picture-28 3. Draw out the 2.5” hard drive from slot. Picture-29... -
Page 20: Lcd
1. Open chassis as the previous guide and disconnect all ports on screen. Picture-30 2. Unscrew four screws on screen mount and take out the screen from the frame. Picture-31... -
Page 21: Touch Control Board
Touch Control Board 1. Open chassis as the previous guide and uncover the tape on the touch control board. Picture-32 2. Disconnect the three ports on the touch control board and replace them (Please carefully disconnect the sponge pad at the bottom of the control card with a knife before taking it out). -
Page 22: Msr
1. Open chassis as the previous guide and unscrew the screw on the cable clip near the left side and disconnect the MSR USB cable from the motherboard. Picture-35 2. Restore the chassis and unscrew screws on the backside of the MSR and then detach the MSR from the POS terminal. -
Page 23: User Notice
Do not disassemble and repair it without permission and contact your supplier in time. Note: 3nStar is not responsible for the damage to the machine and other consequences caused by non-compliance with above user notice, improper use of the machine, unqualified maintenance personnel, or use of accessories not provided...
Need help?
Do you have a question about the PTE0605 and is the answer not in the manual?
Questions and answers