Marantz SR5011 Service Manual page 162

Error DPMS Update Error
Details of Error code
Code Display
Failed to start up Sub in
62 Power On sequence during
Error**62
Update.
Write Enable Latch Bit not
80 set in Read after issuing the
Error**80
"WREN" command.
Block Erase failed in Read after
81
Error**81
issuing the "BE" command.
No Update Packet received
82
Error**82
from CY920 (Time Out).
Abnormal data in Update
83 Packet received from CY920
Error**83
(CRC Error).
Abnormal data in Update
84 Packet received from CY920
Error**84
(PacketNoError).
Setup failure of the XModem
85
Error**85
transfer method.
Mismatched Check Sum in
86 Check Sum comparison after
Error**86
rewriting.
IP Address acquisition failure
A0
Error**A0
(AutoIP).
IP Address acquisition failure
A1
Error**A1
(Time Out).
DPMS login incorrect notifica-
A2
Error**A2
tion.
DPMS connection failure
A4
Error**A4
notification.
Error notification received
A6 while requesting the Firm-
Error**A6
ware Info.
Remedies
Unplug and reconnect the AC plug, and
try again.
Unplug and reconnect the AC plug, and
try again.
If the same error occurs even when it is
retried, the device may be malfunction-
ing.
Unplug and reconnect the AC plug, and
try again.
If the same error occurs even when it is
retried, the device may be malfunction-
ing.
Unplug and reconnect the AC plug, and
try again.
Unplug and reconnect the AC plug, and
try again.
Unplug and reconnect the AC plug, and
try again.
Unplug and reconnect the AC plug, and
try again.
If the same error occurs even when it is
retried, the device may be malfunction-
ing.
Unplug and reconnect the AC plug, and
try again.
Check the network connection, Unplug
and reconnect the AC plug, and try
again.
Unplug and reconnect the AC plug, and
try again.
Check the network connection, Unplug
and reconnect the AC plug, and try
again.
Check the network connection, Unplug
and reconnect the AC plug, and try
again.
Check the network connection, Unplug
and reconnect the AC plug, and try
again.
162
Error DPMS Update Error
Details of Error code
Code Display
Time Out while obtaining
A7
Error**A7
Firmware information.
Error(NG) notification received
AE while requesting Firmware
Error**AE
Download.
Error(Connect failure) notifica-
B0 tion received while request-
Error**B0
ing Firmware Download.
Error in Firmware Download
B1
Error**B1
(Time Out).
Error notification received af-
B2
Error**B2
ter rewriting the CY920 Firm.
Error in Firmware Update
B3
Error**B3
(Time Out).
Failed to transit to Boot
B4
Error**B4
Loader Mode.
Failed to transit to Application
B5
Error**B5
Mode.
---Checking the Firmware Version After the Update---
After updating the firmware, check the version.
See "1. Version Display Mode"
Remedies
Unplug and reconnect the AC plug, and
try again.
Check the network connection, Unplug
and reconnect the AC plug, and try
again.
Check the network connection, Unplug
and reconnect the AC plug, and try
again.
Check the network connection, Unplug
and reconnect the AC plug, and try
again.
Unplug and reconnect the AC plug, and
try again.
Unplug and reconnect the AC plug, and
try again.
Unplug and reconnect the AC plug, and
try again.
Unplug and reconnect the AC plug, and
try again.