Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Alderon Industries VersAlarm I/O VLIO-00005
Summary of Contents for Alderon Industries VersAlarm I/O VLIO-00005
- Page 1 VersAlarm ™ Indoor/Outdoor Alarm Panel USER GUIDE MODEL NUMBER: VLIO-00005...
-
Page 2: Table Of Contents
VersAlarm™ I/O - USER GUIDE Contents Introduction ................................. 3 Safety Guidelines ..............................3 Included with Alarm ..............................4 Features ................................. 5 Installation .................................. 6 Mounting Enclosure and Alarm Float Switch ..................... 6, 7 Connecting Power to Alarm ........................... 7 Testing the Alarm ..............................8 Wiring ................................ -
Page 3: Introduction
4. DO NOT use this product with or near flammable liquids. 5. DO NOT install this product in locations classified as hazardous or in explosive atmospheres as defined by any applicable electrical safety code. Alderon Industries™ - Leading Edge Control Products | 3... -
Page 4: Included With Alarm
(5) RubberLox™ Pipe Clamp The RubberLox™ pipe clamp is included to secure the alarm float switch. (6) Wago Connector The Wago connector is included for ground wire termination. 4 | Alderon Industries™ - Leading Edge Control Products... -
Page 5: Features
(13) Alarm Float Switch/Sensor (not shown) - Pre-installed for (6) Sensor Input - One set of sensor terminals are included for the easy installation. alarm float switch which activates the alarm. Alderon Industries™ - Leading Edge Control Products | 5... -
Page 6: Installation
Note: If using auxiliary contacts, see Wiring step 1 instructions. CAUTION: Do not connect power until installation/wiring is complete and the alarm is ready for testing. Mount alarm float switch Plug power cable into at alarm activation level 230VAC receptacle 6 | Alderon Industries™ - Leading Edge Control Products... -
Page 7: Connecting Power To Alarm
CAUTION: Do not connect power until installation/wiring is complete and the alarm is ready for testing. Alderon Industries™ - Leading Edge Control Products | 7... -
Page 8: Testing The Alarm
The silence condition will reset when the alarm float switch is deactivated. STEP 4: TEST WEEKLY To ensure the product is functioning properly, test once a week. 8 | Alderon Industries™ - Leading Edge Control Products... -
Page 9: Wiring
WAGO peripheral alarm monitors or extensions. 4) NEVER leave ground wire exposed inside the panel, use provided Wago connector for ground termination. See step 3 for installing wire into Wago connector. Alderon Industries™ - Leading Edge Control Products | 9... -
Page 10: General Operation
The applications are not limited to what is listed in this user guide. Follow all individual instructions for the alarm float switch and accessories used with the VersAlarm™ I/O. The following applications can be found in this user guide: Septic Tank Monitoring, Sump Pit Monitoring, and Alarm Auxiliary with Auto Dialer. 10 | Alderon Industries™ - Leading Edge Control Products... -
Page 11: Septic Tank Monitoring
This option would require a shorter alarm float switch cable length and running the power mains out to the alarm. VersAlarm™ I/O Septic Alarm VersAlarm™ I/O Float Drain Field TIME HEAT START 13:27 Cycle: WASH Pump Switch Alderon Industries™ - Leading Edge Control Products | 11... -
Page 12: Sump Pit Monitoring
The silence condition will reset when the alarm float switch deactivates. If the alarm is in silence mode for longer than 24 hours, the alarm will reactivate. VersAlarm™ I/O Alarm House to Yard Float Switch 12 | Alderon Industries™ - Leading Edge Control Products... -
Page 13: Alarm Auxiliary With Auto Dialer
If the alarm is in silence mode for longer than 24 hours, the alarm will reactivate. VersAlarm™ I/O Auto Dialer Alarm House to Yard Float Switch Alderon Industries™ - Leading Edge Control Products | 13... -
Page 14: Troubleshooting
The auxiliary contacts are not activating If the alarm is not activated, then the Test the alarm and the auxiliary contacts auxiliary contacts should also be off should work while the alarm is activated 14 | Alderon Industries™ - Leading Edge Control Products... -
Page 15: Specifications
Caution: changes/mod- ifications not approved by Alderon Industries could void the user’s authority to operate the equipment. Altra™ Alarm Float Switch... -
Page 16: Warranty Information
Three-Year Limited Warranty - Standard Products LIMITED WARRANTY: Subject to the conditions of this Three-Year Limited Warranty, Alderon Industries, LLC (“Alderon”) war- rants to the original user or consumer of an Alderon product (the “Product”) that, for a period of three (3) years from the date of manufacture, the Product will be free from defects in materials and workmanship under normal use and service, and provided the Product is installed, operated and maintained in accordance with instructions supplied by Alderon. - Page 17 VersAlarm™ I/O - USER GUIDE This page intentionally left blank Alderon Industries™ - Leading Edge Control Products | 17...
- Page 18 VersAlarm™ I/O - USER GUIDE This page intentionally left blank 18 | Alderon Industries™ - Leading Edge Control Products...
- Page 19 VersAlarm™ I/O - USER GUIDE This page intentionally left blank Alderon Industries™ - Leading Edge Control Products | 19...
-
Page 20: Company Information
UG00005_Rev04_VLIO-00005_VersAlarm IO | March 25, 2022 1:49 PM Company Location: 151 16th Street South, Hawley, MN 56549 Mailing Address: PO Box 827, Hawley, MN 56549 Main Office Phone: 218.483.3034 Website: alderonind.com General Inquiry Email: info@alderonind.com Submit New Orders: orders@alderonind.com...
Need help?
Do you have a question about the VersAlarm I/O VLIO-00005 and is the answer not in the manual?
Questions and answers