BES X Installation Manual, Rev.9, Jun 2018 Table of Contents Table of Contents TABLE OF CONTENTS ....................... 1 SUMMARY OF CHANGES ......................6 GENERAL INSTALLATION NOTES ....................7 RJ45 CONNECTORS......................... 8 SYSTEM COMPONENTS ....................9 1.1 - 4HD-HUB and 5HD-HUB ......................10 1.1.1 -...
Page 4
Centers with: up to 12 lanes, MMS or TCS or Q-COM and single channel video server..70 T.20.092 – BES X scoring network with: up to 12 lanes, MMS or TCS or Q-COM and single channel video server ............................71 5.2.3 -...
Page 5
5.3 - Centers with more than 12 lanes and up to 68 lanes or split-house ........74 T.20.094 – BES X scoring network for centers with more than 12 lanes and up to 68 lanes ....75 5.4 - Centers with more than 68 lanes or split-house ..............76 T.20.095 –...
Page 6
14.1.1 - Turning ON the system......................140 14.1.2 - Turning OFF the system....................... 140 14.2 - How to boot the BES X system in emergency (in the case of a ConquerorPRO server PC crash) ............................. 140 14.2.1 - How to open a lane from an EasyKey bowler terminal............141 14.2.2 - How to open a lane from a SuperTouch bowler terminal.
Page 7
BES X Installation Manual, Rev.9, Jun 2018 Table of Contents P/N: 400288005...
Added the 5HD-CPU. REV 7 (February 2016) Added the paragraph “How to boot the BES X system in emergency (in the case of a ConquerorPRO server PC crash)”. Added the BES X Dual Mode installation and configuration paragraph.
BES X Installation Manual, Rev.9, Jun 2018 General Installation Notes General Installation Notes For devices directly connected to the power, it is necessary to check that the electrical capacity of the system is suitable for the maximum power requirements of the equipment (as indicated on the labels of the equipment).
BES X Installation Manual, Rev.9, Jun 2018 RJ45 connectors. RJ45 connectors. Each connector internally have sharp prongs that when crimped pierce the insulation of the wire and connect with the conductor. Ethernet cables may have solid or stranded wire conductors and the sharp prongs are different in the connectors made for each type of wire.
System components The core of the BES X scoring system is composed by two units: the 4HD/5HD-HUB and the 4HD/5HD-CPU units. Install this couple of units for each pair of lanes present in the bowling center, as explained in this manual.
BES X Installation Manual, Rev.9, Jun 2018 System components 1.1.2 - 5HD-HUB label description The image above displays the label located on the side of the 5HD-HUB unit. 1. Manufacturer (QubicaAMF Europe S.p.A.); 2. Part number (P/N: 288250025); 3. List of certifications (CE certification);...
BES X Installation Manual, Rev.9, Jun 2018 System components L3 ODD console COM line: Network connection with POE for the odd lane console (EasyKey or SuperTouch models only). When a single console per pair of lanes is installed, this output is not used.
5HD HUB Upper View N1 - Scoring network 5HD HUB Front View Network Provide an Earthing con- nection before the mains plug is connected to the mains. When disconnect- ing the earthing connec- tion, be sure to disconnect it by pulling out the mains plug from the mains.
HD HUB Upper View HD HUB N1 - Scoring network Front View Network Provide an Earthing conne- ction before the mains plug is connected to the mains. When disconnecting earthing connection, be su- re to disconnect it by pulling out the mains plug from the mains.
HD HUB Upper View HD HUB N1 - Scoring network Front View Network Provide an Earthing conne- ction before the mains plug is connected to the mains. When disconnecting earthing connection, be su- re to disconnect it by pulling out the mains plug from the mains.
IMPORTANT NOTE: the 5HD-CPU unit, P/N: 288250023, is supported by ConquerorPRO version 12 or higher. The 4HD-CPU and 5HD-CPU are the graphic engine of the BES X scoring system. Their functionality is to display the scoring grids, the animations, the different environments, etc… They are connected to the 4HD/5HD-HUB unit with a single network cable and must be installed near the overhead monitors.
BES X Installation Manual, Rev.9, Jun 2018 System components 1.2.2 - 5HD-CPU Label description The image above displays the label located on the side of the 5HD-CPU unit. 1. Manufacturer (QubicaAMF Europe S.p.A.); 2. Name of the unit (5HD-CPU); 3. Part number with bar code (P/N: 288250023);...
BES X Installation Manual, Rev.9, Jun 2018 System components 1.2.4 - Connections On the 4HD/5HD-CPU the following connections are available: Connectors on the upper side of the 4HD/5HD-CPU unit: EXTERNAL POWER SUPPLY: AC/DC external power supply. Not used when the 4HD/5HD-CPU is used for score purposes.
Attention: Ne pas ouvrir l’appareil. Il n’y a aucune pièce réparable à l’intérieur. Confiez toute réparation à un personnel autorisé. Le garantie expire si l’étiquette a été altérée. この にはユーザーで できる External Refer to manual. Use Even only P/N: 288201029-xx Power はありません。このボックスを けた Supplied by QubicaAMF Supply Ctrl Ctrl Ctrl HDMI HDMI は、いかなる も...
Warning: No User Serviceable Parts Inside, Contact Authorized Dealer for Assistance. Warranty Voided if Seals are Broken only P/N: 288201029-xx Power Attention: Ne pas ouvrir l’appareil. Il n’y a aucune pièce réparable à l’intérieur. Confiez toute réparation à un personnel autorisé. Supplied by QubicaAMF Le garantie expire si l’étiquette a été altérée. Supply この にはユーザーで...
T. 0.0 This drawing shows how the 4HD-CPU is fixed to the monitor frame. MOUNTING THE The 5HD-CPU is mounted in exactly the same way as the 4HD-CPU. 4HD/5HD-CPU ON A SINGLE MONITOR FRAME APR 27th...
T. 0.0 This drawing shows how the 4HD-CPU is fixed to the monitor frame. MOUNTING THE The 5HD-CPU is mounted in exactly the same way as the 4HD-CPU. 4HD/5HD-CPU ON A DOUBLE MONITOR FRAME APR 27th...
CPU unit This drawing shows how the 4HD-CPU have to be fixed to the wall. mounting The 5HD-CPU is mounted in exactly the same way as the 4HD-CPU. 4HD-CPU Dimensions Heigth 190 mm 7.49” Length 185 mm 7.28” Depth 68 mm 2.68”...
Page 26
BES X Installation Manual, Rev.9, Jun 2018 P/N: 400288005...
Page 28
BES X Installation Manual, Rev.9, Jun 2018 Electrical specifications Provide AC power to the system components via an electrical subpanel that is dedicated solely to the BES X system. The subpanel must have a neutral bus and a separate insulated third-wire isolated ground that is connected at the main service panel only.
BES X Installation Manual, Rev.9, Jun 2018 BES X system configurations IMPORTANT NOTE : Never, for any reason, run low voltage signal cables (such as network cables) near any kind of high voltage source. 3.1 - No console present This is the simplest configuration. On each pair of lanes there will be installed: ...
BES X system configurations 3.2 - EasyKey console brief description The EasyKey console is the keyboard console. It gives access to the basic on-lane functions of the BES X system. The EasyKey console is InterCom ready. This fact does not means that the InterCom system will be available on the lanes, because the InterCom have to be purchased separately (Q-Com system).
GROUND WIRE HD CPU CONNECTION L1 - Black ONTROL a l l r t a EVEN EVEN ODD i n g l a v l a c L1 - Black r / s F r o s t e i t c EASYKEY 4HD/5HD Q-Vision...
Due to this fact the connection cable for the speaker is slightly different between the two situations. Each console has to be connected to ground. Please refer to the section “5 – Suggested ground connection” of the BES X – PRE-Installation Manual for further information. P/N: 400288005...
GROUND WIRE ODD LANE HD CPU CONNECTION EASYKEY L1 - Black ONTROL SPEAKER a l l r t a EVEN EVEN ODD i n g l a v l a c L1 - Black r / s F r o s t e EVEN LANE i t c...
GROUND WIRE ODD LANE HD CPU CONNECTION EASYKEY L1 - Black ONTROL SPEAKER a l l r t a EVEN EVEN ODD i n g l a v l a c L1 - Black r / s F r o s t e EVEN LANE i t c...
4HD-HUB side to the 288401035 cable adapter then the 288401035 cable adapter to the P1 connector of the 4HD-HUB unit. Each console has to be connected to ground. Please refer to the section “5 – Suggested ground connection” of the BES X – PRE-Installation Manual for further information. P/N: 400288005...
GROUND WIRE HD CPU CONNECTION L1 - Black ONTROL SPEAKER a l l r t a SPEAKER EVEN EVEN ODD i n g l a v l a c L1 - Black r / s F r o s t e EVEN LANE i t c SUPERTOUCH...
GROUND WIRE HD CPU CONNECTION L1 - Black ONTROL a l l SPEAKER r t a EVEN EVEN ODD i n g l a v l a c L1 - Black r / s F r o s t e EVEN LANE i t c SUPERTOUCH...
4HD-HUB side to the 288401035 cable adapter then the 288401035 cable adapter to the P1 connector of the 4HD-HUB unit. Each console has to be connected to ground. Please refer to the section “5 – Suggested ground connection” of the BES X – PRE-Installation Manual for further information. P/N: 400288005...
GROUND WIRE ODD LANE HD CPU CONNECTION SUPERTOUCH L1 - Black ONTROL SPEAKER a l l r t a PORT SPEAKER EVEN USED EVEN ODD i n g l a v l a c L1 - Black r / s F r o s t e EVEN LANE...
GROUND WIRE ODD LANE HD CPU CONNECTION SUPERTOUCH L1 - Black ONTROL a l l SPEAKER r t a PORT EVEN USED EVEN ODD i n g l a v l a c L1 - Black r / s F r o s t e EVEN LANE i t c...
PARTS LIST ITEM DESCRIPTION 286002802 Base sheet metal - Lower 286002806 Base sheet metal - Higher 286002857 Console extrusion machined 286002859 Console extrusion short 286002866 V-Support single assembly 286002852 V-Support back 286002854 Front base cover 286002855 Rear base cover 286002824 Speaker wire harness single 770047105 Speaker...
PARTS LIST ITEM DESCRIPTION 286002802 Base sheet metal - Lower 286002806 Base sheet metal - Higher 286002857 Console extrusion machined 286002866 V-Support single assembly 286002852 V-Support back 286002854 Front base cover 286002855 Rear base cover 286002824 Speaker wire harness single 770047105 Speaker 741510403...
PARTS LIST ITEM DESCRIPTION 286002802 Base sheet metal - Lower 286002806 Base sheet metal - Higher 286002814 Console extrusion machined 286002826 Console extrusion short 286002820 V-Support single assembly 286002807 V-Support back 286002815 Front base cover 286002816 Rear base cover 286002824 Speaker wire harness single 770047105 Speaker...
PARTS LIST ITEM DESCRIPTION 286002802 Base sheet metal - Lower 286002806 Base sheet metal - Higher 286002857 Console extrusion machined 286002867 V-Support dual assembly 286002852 V-Support back 286002854 Front base cover 286002855 Rear base cover 286002819 Speaker wire harness 770047105 Speaker 741510403 3/4"...
PARTS LIST ITEM DESCRIPTION 286002802 Base sheet metal - Lower 286002806 Base sheet metal - Higher 286002857 Console extrusion machined 286002867 V-Support single assembly 286002852 V-Support back 286002854 Front base cover 286002855 Rear base cover 286002819 Speaker wire harness single 770047105 Speaker 741510403...
PARTS LIST ITEM DESCRIPTION 286002802 Base sheet metal - Lower 286002806 Base sheet metal - Higher 286002814 Console extrusion machined 286002821 V-Support dual assembly 286002807 V-Support back 286002815 Front base cover 286002816 Rear base cover 286002819 Speaker wire harness 770047105 Speaker 741510403 3/4"...
INSTALLATION INSTRUCTIONS: 1. Remove V-Support back. LCD OR KEYBOARDS 2. Remove or keyboard if already installed. 3. Remove V-support single or dual. 4. Remove all 5 V-support mounting screws. 5. Locate console table plate (item 1) on the pedestal extrusion as shown. 6.
[249.8] Assemble V-Support back (item 3) to V-Support (item 2). 9.84 Secure with two screws (item 7). Take care not to pinch speaker wire harness. T. 0.0 [319.9] 12.60 286002869 BES X CONSOLE TABLE MOUNT ASSEMBLY JUN 20th...
Assemble V-Support back (item 3) to V-Support (item 2). [249.8] Secure with two screws (item 7). 9.84 Take care not to pinch speaker wire harness. T. 0.0 [319.9] 12.60 286002840 BES X CONSOLE TABLE MOUNT ASSEMBLY MAY 6th...
(item 1). 7. Secure the X base to the floor and mounting plate. 8. Continue with the installation of the X pedestals. T. 0.0 [482.6] 610325104 KIT FOR MOUNTING 19.00 TWO BES X PEDESTALS AT 96° (286002845) MAY 21st...
(item 1). 7. Secure the X base to the floor and mounting plate. 8. Continue with the installation of the X pedestals. [508] T. 0.0 20.00 610325104 KIT FOR MOUNTING TWO BES X PEDESTALS AT 60° (286002846) MAY 21st...
8. Routing the cables thru the opening in the rear base cover FMW. 9. Cut the cable cover top part (2) to fit snugly between the rear base cover FMW (1) and the 610325104 KIT FOR MOUNTING ONE BES X SINGLE PEDESTAL cable entry. (286002847) 10.
QubicaAMF supplies scoring network switches with 8 ports. One additional network switch will be supplied for TCS or MMS Digital kits. QubicaAMF also supplies the network cables needed for the installation. Each cable’s length is dimensioned according to the distance between each 4HD/5HD-HUB unit and the main (or slave) scoring network switch (refer to table T.20.096 and T.20.079 for standard installations or to table...
S C O R I S C O R I O R K O R K N E T W N E T W S W I T C S W I T C XLi pinspotters with safety kit XLi pinspotters with safety kit UPPER VIEW REAR VIEW 7 t h...
If the bowling center has up to 12 lanes just one network switch for the scoring network is needed. When MMS digital, TCS or Q-COM systems are purchased, QubicaAMF will supply additional switches and the scoring network will have different configurations.
3 r d 3 r d 2 n d 2 n d 1 s t 1 s t Single Channel Video Server T. 0. 2 091 BES X SCORING NETWORK WITH: UP TO 12 LANES AND SINGLE CHANNEL VIDEO SERVER JAN 3rd...
5.2.2 - Centers with: up to 12 lanes, MMS or TCS or Q-COM and single channel video server. Two 8 ports network switches will be supplied by QubicaAMF for this configuration. The connections for the main scoring network switch are: ...
2 n d 2 n d 1 s t 1 s t Single Channel Video Server T. 0. 2 092 BES X SCORING NETWORK WITH: UP TO 12 LANES, MMS OR TCS OR Q-COM AND SINGLE CHANNEL VIDEO SERVER JAN 3rd...
Scoring network 5.2.3 - Centers with: up to 12 lanes, MMS, TCS, Q-COM and single channel video server. Three 8 ports network switches will be supplied by QubicaAMF for this configuration. The connections for the main scoring network switch are: ...
3 r d 2 n d 2 n d 1 s t 1 s t Single Channel Video Server T. 0. 2 093 BES X SCORING NETWORK WITH: UP TO 12 LANES, MMS, TCS, Q-COM AND SINGLE CHANNEL VIDEO SERVER JAN 3rd...
The slave switches must be connected to the main scoring network switch in UPLINK mode. UPLINK mode is automatically set in switches supplied by QubicaAMF, other switches may need a manual setting. QubicaAMF suggests the installation of a cable conduit along the whole length of the curtain wall, to accommodate the network cables.
2 n d 2 n d 1 s t 1 s t Single Channel Video Server T. 0. 2 094 BES X SCORING NETWORK FOR CENTERS WITH MORE THAN 12 LANES AND UP TO 68 LANES OR SPLIT-HOUSE JAN 3rd...
If the bowling center has more than 68 lanes additional scoring network switches that act as slaves are needed. QubicaAMF will supply one 16 port network switch to be used as main scoring network switch in the place of an eight port network switch.
1 s t Single Channel Video Server T. 0. 2 095 BES X SCORING NETWORK FOR CENTERS WITH MORE NOTE: Refer to «5.4 - Centers with more than 68 lanes» section THAN 68 LANES of the « X Installation manual» for further information.
I T C Front Desk Front Desk 2 Front Desk 3 Conqueror Server USB Key USB Key ConquerorPRO ConquerorPRO License License ConquerorNET SWITCH Scoring NET T. 0. 2 081 BES X CONNECTION TO FRONT DESK Wall Mounting Box MAY 21st...
THIS DRAWING IS INDICATIVE. ALWAYS CHECK THE COLOR SEQUENCE ON THE INSTRUCTIONS ATTACCHED TO THE WALL MOUNTING BOX FOR T568B WIRING. - Strip approximately 30mm of the cable jacket,and separate to 4 pair each. - Follow the direction on the color-coding to position T568B wiring, separate a little space on proper position and insert the wire pair by pair into each slot.
Page 86
The LCOM network runs through a four-wire cable, with two wires carrying the power and two wires carrying the communications bi-directional signal. QubicaAMF supplies 60ft – 20m of LCOM cable for each pair of lanes, enough for a standard installation. Every LCOM device is exclusively powered through the LCOM line.
BES X Installation Manual, Rev.9, Jun 2018 LCOM line 6.1 - LCOM wiring The correct wiring for each LCOM device is made keeping the Phoenix connector in your hand, as shown in the picture below. The pin number 1 is the first starting from the left.
Page 88
BES X Installation Manual, Rev.9, Jun 2018 LCOM line Power wires The 4HD/5HD-HUB C1 - LCOM connector supplies the power to all the LCOM electronic devices. The first wire on top is the positive power, while the fourth wire on the bottom is the negative; this pair of wires is also called LCOM power wires.
Page 89
BES X Installation Manual, Rev.9, Jun 2018 LCOM line 1. Turn the 4HD/5HD-HUB off. 2. Unplug the C1 - LCOM connector from the 4HD/5HD-HUB. 3. Turn the 4HD/5HD-HUB on again and wait for the LCOM error code on screen. 4. Then, being extremely careful to do not cause a short circuit, measure the voltage between the 2nd (-) and 3rd (+) pins of the C1 male connector.
Page 90
BES X Installation Manual, Rev.9, Jun 2018 P/N: 400288005...
The overhead monitors (or lane monitors) are installed on the Bowl Return area. The 4HD/5HD-CPU is the graphic engine of the BES X system, that can provide up to two independent video outputs for the scoring system, but can control (monitor ON/OFF, channel change, etc. only on supported monitors) up to three monitors (two for the scoring system and one with an independent video signal).
“HDMI-CEC” capabilities on monitors supplied by QubicaAMF With monitors supplied by QubicaAMF follow one of the procedures listed below, according to the brand / model of the monitors, in order to enable the “Just Scan” (or “Screen Fit”) capability. ACCUVISION MONITORS Gen.3 and Gen.4: How to enable the control “HDMI-CEC”:...
Page 94
BES X Installation Manual, Rev.9, Jun 2018 Overhead monitors SAMSUNG MD SERIES MONITORS: How to enable the “JUST SCAN” (or “Screen Fit”) option: If the image displayed on the monitor is larger than the monitor screen, follow this procedure in order to have a correct aspect ratio: ...
Support Ceiling HD/5HD CPU 5.25 feet - 1.60m Console minimum height 8.20 feet - 2.50m Ball Return Unit Lane Underlane Area T. 0.0 2" conduct For low voltage wiring MONITOR POSITION MAY 2nd...
AccuVision monitors only. /5HD- connection in the case that the monitors does NOT support control through /5HD- connection in the case HDMI connector. that the monitors support control through the HDMI connector. 5HD-CPU 5HD-CPU Even Ctrl Ctrl Ctrl HDMI HDMI Even Ctrl Ctrl...
NOTE: FIX THE QUBICAAMF INFRARED TRANSMITTER OVER THE MONITOR INFRARED RECEIVER 610325206 5HD-CPU INFRARED TRANSMITTER Even Ctrl Ctrl Ctrl HDMI HDMI 4HD-CPU EVEN LANE ODD LANE THIRD MONITOR MONITOR ONTROL MONITOR T. 0.0 610325206 EVEN LANE ODD LANE THIRD INFRARED TRANSMITTER...
Page 98
BES X Installation Manual, Rev.9, Jun 2018 P/N: 400288005...
USA ONLY CATV SOURCE NOTES: 1. All unused inputs or output of taps, splitters or amplifiers must be terminated. 2. On the CATV directional coupler, observe the direction of the signal flow. " " should always " FACE " the amplifier. 3.
16dB From Amplifier previous 4 Way Coupler To next 4 Way Coupler Terminator AccuVision AccuVision AccuVision AccuVision AccuVision AccuVision AccuVision AccuVision T. 0.0 CABLE TELEVISION INSTALLATION, DETAIL OF FOUR LANES NOV 26th...
Page 102
BES X Installation Manual, Rev.9, Jun 2018 P/N: 400288005...
The ConquerorPRO server is equipped with a second network card, as are all other computers supplied by QubicaAMF. Only the ConquerorPRO server is to be connected to the Scoring Network (Scoring NET). The Scoring Network (Scoring NET) is kept separated from the PC network (Conqueror NET), and has a different IP address matrix.
192.168.71.xxx, while the address matrix for the Scoring NET is 192.168.216.xxx. The Front Desk computer can be equipped with a second network card, or QubicaAMF will provide a “RJ45 to USB” adapter in order to connect to a USB port of the Front Desk computer the homerun cable of the Scoring NET.
BES X Installation Manual, Rev.9, Jun 2018 Front Desk 9.3 - Lanes Control Box Service The Lanes Control Box Service (called also Matrix Configuration service or MxServer) is the program that manages the allocation of IP addresses of the 4HD/5HD-CPU boxes each time they boot up.
The 288201089 single channel video server unit is the hardware needed to broadcast a video signal from a single source to the BES X system. The video signal is broadcasted in 720x576 (Standard Definition) for a PAL video signal and in 720x480 (Standard Definition) for a NTSC video signal.
Page 109
BES X Installation Manual, Rev.9, Jun 2018 Single channel video server In the menu on the left click on “Video” under “Stream Config”, select “PAL” as “Video Standard” and click on “Submit”. In the menu on the left click on “Output” under “Stream Config”, select “PAL” as “Video Standard”...
4HD/5HD-HUB units. The video signal is broadcasted in 720x576 (Standard Definition) for a PAL video signal and in 720x480 (Standard Definition) for a NTSC video signal. The 288201034 unit has a Static IP address pre-assigned by QubicaAMF. The default IP address of the 288201034 unit is: ...
Power cord supplied by QubicaAMF Model 2453S Video Server Serial CNTADABNCRCA TO MAIN SCORING NET SWITCH T. 0. 9 247 288201089 SINGLE CHANNEL FROM TUNER VIDEO SERVER WIRING VIDEO SOURCE APR 25th...
I N G I T C The Main Scoring NET Switch is located on the curtain wall S L A I N G I T C Wall Mounting Box MUST The Single Channel Video Server cable be connected to a Slave Scoring NET Switch Solid Cat.5 Cable with Cat.5e wall...
Page 114
BES X Installation Manual, Rev.9, Jun 2018 P/N: 400288005...
HD CPU For this installation the 4 HD HUB Rev.2 REQUIRED L1 - Black P/N: 288250018 is ONTROL In case on InterCom set the Sensitivity to level by opening the Microphone Sensitivity Jumper ( 6) a l l QIT RDB r t a -switch settings EVEN...
HD CPU For this installation the 4 HD HUB Rev.2 REQUIRED L1 - Black P/N: 288250018 is ONTROL In case on InterCom set the Sensitivity to level by opening the Microphone Sensitivity Jumper ( 6) a l l QIT RDB r t a -switch settings EVEN...
HD CPU For this installation the 4 HD HUB Rev.2 In case on InterCom set the Sensitivity to level REQUIRED L1 - Black P/N: 288250018 is by opening the Microphone Sensitivity Jumper ( 6) ONTROL ODD CONSOLE QIT RDB EVEN CONSOLE QIT RDB -switch settings -switch settings 1 2 3 4...
HD CPU For this installation the 4 HD HUB Rev.2 In case on InterCom set the Sensitivity to level REQUIRED L1 - Black P/N: 288250018 is by opening the Microphone Sensitivity Jumper ( 6) ONTROL QIT RDB -switch settings 1 2 3 4 1 2 3 4 a l l r t a...
HD CPU For this installation the 4 HD HUB Rev.2 REQUIRED L1 - Black P/N: 288250018 is ONTROL a l l r t a EVEN EVEN ODD i n g l a v L1 - Black r / s F r o l a c s t e i t c...
HD CPU For this installation the 4 HD HUB Rev.2 REQUIRED L1 - Black P/N: 288250018 is ONTROL a l l r t a EVEN EVEN ODD i n g l a v L1 - Black r / s F r o l a c s t e i t c...
Page 122
BES X Installation Manual, Rev.9, Jun 2018 P/N: 400288005...
Once the hardware of the BES X system has been correctly installed, as described above in this manual, follow these steps in order to configure ConquerorPRO with the new scoring system.
Page 125
BES X Installation Manual, Rev.9, Jun 2018 System first start-up 5. Enter the serial number of the 4HD/5HD-CPU. Set also the number of the monitors, the pinsetter interface, the keyboards type and all other desired options (refer to the “12.2 – Lane setup parameters screen brief description”...
Page 126
17. The Reinitialize procedure will now start. NOTE: This procedure will take more than an hour to finish. DO NOT switch off the BES X system during the Reinitialization process. 18. Now the ODD overhead monitor will turn off (or will display a black screen, or will display the message “no signal”, depending on the model of the monitor) while the monitor on the EVEN lane...
Page 127
BES X Installation Manual, Rev.9, Jun 2018 System first start-up 19. Within five minutes (from the “system halted” message) each pair of lanes will restart automatically, or each pair of lanes can be restarted manually by unplugging and plug back the power cord of the 4HD/5HD-HUB.
Page 128
BES X Installation Manual, Rev.9, Jun 2018 System first start-up 30. Select the target lanes, enable the Reset option and press OK. 31. When the parameters have been uploaded the system will reboot. 32. In the case of SuperTouch LCD monitors have been installed, they will start to load the programs.
BES X Installation Manual, Rev.9, Jun 2018 System first start-up 12.2 - Lane setup parameters screen brief description Available: Uncheck this option if the lane is not available (when the 4HD/5HD-CPU serves a single lane instead of a pair of lanes).
Page 130
BES X Installation Manual, Rev.9, Jun 2018 System first start-up English rectangular (en-us_001_001): English oval (en-us_004_001): Universal 2008 (en-us_008_001): Universal 2012 (en-us_009_001), Chinese 2012 Backlight (en-us_009_001) and Eastern Europe 2012 Backlight (en-us_009_001): P/N: 400288005...
Page 131
BES X Installation Manual, Rev.9, Jun 2018 System first start-up Japanese rectangular (ja_002_001): Japanese oval (ja_005_001): Japanese 2008 (ja_008_003): Japanese 2012 Backlight (ja_009_003): P/N: 400288005...
Page 132
BES X Installation Manual, Rev.9, Jun 2018 System first start-up German oval (de-de_006_001): Russian oval (ru_007_001): Russian 2008 (ru_008_002): Russian 2012 Backlight (ru_009_002): P/N: 400288005...
Page 133
BES X Installation Manual, Rev.9, Jun 2018 System first start-up Swedish oval (sv-se_006_001): English touch screen (en-us_TOUCH) and Chinese touch screen (en-us_TOUCH): SuperTouch console with English language. Japanese touch screen (ja_TOUCH): SuperTouch console with Japanese language. ...
Page 134
BES X Installation Manual, Rev.9, Jun 2018 System first start-up 2. the monitor connected to the 4HD/5HD-CPU will show an image but it does not properly fit on the screen and on the monitor there is no option to adjust the image. In order to fix this issue you can use the “View size”...
BES X Installation Manual, Rev.9, Jun 2018 System boot up sequence 13.1 - Boot-up screen description During the boot-up of the system, it will be displayed the following picture (note that this picture is only an example): This is an example of the boot-up screen that is displayed on the lane monitors during the boot-up sequence of the BES X system.
Page 137
BES X Installation Manual, Rev.9, Jun 2018 System boot up sequence After this process, the boot-up of the system is not completed and, if the system is not requesting for a reinitialize or a program upload, the screen changes as in the following picture: 1.
BES X Installation Manual, Rev.9, Jun 2018 System boot up sequence Test 4HD-TB on L4: 1 wired console with keypad is connected to the L4 port of the 4HD/5HD- HUB unit (one per pair). ONLY WITH 4HD-HUB REV.2: Test Tb on D2: 1 wired console with keypad is connected to the D2 port of the 3QT unit (one per pair).
Page 139
BES X Installation Manual, Rev.9, Jun 2018 System boot up sequence Consoles: Error 151 One EasyKey console has been installed with the 286-002-819 speaker cable, while the other EasyKey console has been installed with the 286-002-824 speaker cable. Error 190...
Page 140
(9) The microprocessor on the F-Box as an old version loaded on it and the lane cannot be configured to handle the strike signal. (10) Internal errors that should be reported to QubicaAMF. To restart the program manually restart the 4HD/5HD-HUB.
QubicaAMF suggest to turn off the scoring system every night to save power. 14.1.1 - Turning ON the system. This is the procedure to follow in order to turn on the system in the mornings for BES X Scoring systems: ...
To open a lane in emergency from an EasyKey bowler terminal, press the button and follow the sign-in procedure, explained in the “BES X user interface Manual – EasyKey”. 14.2.2 - How to open a lane from a SuperTouch bowler terminal.
Select the destination lanes of the 4HD/5HD-CPU and press OK Click on the “Select” button. In the window “Select BES X Animations” select “From repository” and click on the “Ok” button. Click on the “Ok” button on the window that appears. ...
Page 145
BES X Installation Manual, Rev.9, Jun 2018 How to Once the download process is finished will appear a user message reporting the completion of the process. Click on the “Done” button. Open the “Upload animations” screen by clicking on the icon on the left of the screen (or by selecting Setup / Technical Setup / Upload Animation from the ConquerorPRO main menu, if the upload animations screen has been previously closed).
BES X Installation Manual, Rev.9, Jun 2018 How to 14.4.1 - Upload Animations buttons brief description Select Button: This function will open a selection screen named “Select BES X Animations” giving the user two choices: From repository: this process will synchronize the animations present in the “Internet Update”...
BES X Installation Manual, Rev.9, Jun 2018 How to 14.5 - How to configure the speaker and microphone for the Virtual Waiter in Windows The Virtual Waiter feature to function properly needs that the hardware device used for the playback of the sound is set as the Default device and the desired audio input device is the only audio input device enabled and has to be set as the Default audio input device.
Page 148
BES X Installation Manual, Rev.9, Jun 2018 How to Select the Microphone of the installed headset (in this example we used the Logitech Wireless Headset) and click on the “Set Default” button Click on “OK” once finished to close the Sound window.
15.1 - Introduction In this section, we will describe only the installation for the extra devices needed to interface the BES X system with a Highway66, as the installation of the BES X units is similar to a standard scoring installation and the connections between the different units are the same.
BES X Installation Manual, Rev.9, Jun 2018 BES X Dual Mode 15.3 - Software setup Follow the procedure described in the section “12 – System first startup” of this manual, but apply the following modifications to the Lane Setup parameters (in ConquerorPRO): 15.3.1 - Dual Mode ConquerorPRO Lane Setup...
Page 156
BES X Installation Manual, Rev.9, Jun 2018 P/N: 400288005...
BES X Installation Manual, Rev.9, Jun 2018 Replacements 16.1 - How to replace the 4HD/5HD-HUB unit This is the procedure to follow in order to replace a faulty 4HD/5HD-HUB: Turn off the faulty 4HD/5HD-HUB by unplugging the power cord from the 4HD/5HD-HUB unit itself;...
Page 159
BOX; Wait for the ConquerorPRO to process the request; NOTE: This procedure will take almost an hour to finish. DO NOT switch off the BES X system during this process. When the whole process is completed, a confirmation message (LANE CONTROL BOX REPLACED) will appear.
BES X Installation Manual, Rev.9, Jun 2018 Replacements 16.3 - How to replace an EasyKey console This is the procedure to follow in order to replace a faulty EasyKey console: Turn off the 4HD/5HD-HUB by unplugging the power cord from the 4HD/5HD-HUB unit, in order to turn off the couple of lanes where the faulty EasyKey console is installed;...
Page 161
The Reinitialize procedure will now start. NOTE: This procedure will take almost an hour to finish. DO NOT switch off the BES X system during the Reinitialization process. When the Reinizialization process will finish, the system will boot up.
Page 162
BES X Installation Manual, Rev.9, Jun 2018 P/N: 400288005...
: 288250023 5HD CPU : 288150021 EasyKey International EasyKey Russian PN : 288150022 EasyKey Japanese PN : 288150023 : 288150024 SuperTouch SuperTouch Ver.2 PN: 288150026 T. 0. 9 237 Please visit BES X http://eshop.qubicaamf.com PARTS for further information MAY 21st...