Lifetime 1044 Assembly Instructions Manual
  1. Manuals
  2. Brands
  3. Lifetime Manuals
  4. Sports & Outdoors
  5. QUICK ADJUST 1044
  6. Assembly instructions manual

Lifetime 1044 Assembly Instructions Manual

Conversion kit
Hide thumbs Also See for 1044:
Table of Contents

Advertisement

Quick Links

Download this manual
QUICK ADJUST
®
CONVERSION KIT
MODEL 1044
BEFORE ASSEMBLY:
• Before starting, decide where to mount the system: to a pole or to a wall. A mounting kit
is required for roof mounts and is available through our customer service department
(see page 11)
• At least 2 people recommended for setup
SAVE THIS INSTRUCTION IN THE EVENT THE MANUFACTURER MUST TO BE CON-
TACTED TO OBTAIN REPLACEMENT PARTS.
TOOLS AND PARTS REQUIRED (NOT INCLUDED)
1/2" (≈13 mm)
(2)
9/16" (≈14 mm)
(2)
2" x 4" x 20" (≈5 x 10 x 51 cm) Board
(2)
QUESTIONS?
CONTACT LIFETIME CUSTOMER SERVICE:
Dial 1-800-225-3865
7:00 am-5:00 pm (M-F) MST
and 9:00 am-1:00 pm (Saturday) MST
3/8" (≈10 mm)
(1)
3/4" (≈19 mm)
(2)
Or
Live Chat: www.lifetime.com/customerservice
(click on the "LIVE CHAT" tab)
ASSEMBLY INSTRUCTIONS
Pour le français, voir la page 2. Para el español, ver la página 3.
Rim, backboard and net sold separately.
7/16" (≈11 mm)
(2)
(1)
3.5" x 105"-3.5" x 112"
(≈8,9 x 266,7 cm-8,9 x 284,5) Pole
For Customer Service in Mainland Europe and the
United Kingdom,
E-mail: cs@lifetimeproducts.eu
1

TABLE OF CONTENTS

Icon Legend..................................................................4
Warnings & Notices......................................................5
Pole-Mount Assembly...................................................6
Wall-Mount Assembly.................................................15
Impact
Combo Assembly...........................................22
®
Fusion
Combo Assembly............................................31
®
Parts Identifi er..........................................................i-iv
Steel-Framed Combo Assembly.................................41
Pole Installation..........................................................60
Wall Installation..........................................................62
Adjustment of the Quick Adjust
...............................64
®
Maintenance............................................................65
Warning Sticker..........................................................66
Registration...............................................68
Warranty....................................................69
MODEL# AND PRODUCT ID
(both are needed when contacting us)
Model Number: 1044
Product ID:

Advertisement

Table of Contents
loading

Related Manuals for Lifetime 1044

Summary of Contents for Lifetime 1044

  • Page 1: Table Of Contents

    3.5" x 105"–3.5" x 112" 2" x 4" x 20" (≈5 x 10 x 51 cm) Board (≈8,9 x 266,7 cm–8,9 x 284,5) Pole QUESTIONS? CONTACT LIFETIME CUSTOMER SERVICE: MODEL# AND PRODUCT ID (both are needed when contacting us) Model Number: 1044 Dial 1-800-225-3865 Live Chat: www.lifetime.com/customerservice...
  • Page 2 Bloc en bois 2 x 4 x 20 po (≈5 x 10 x 51 cm) (3.5" x 105"–3.5" x 112") N° DE MODÈLE ET RÉFÉRENCE DU ® QUESTIONS ? CONTACTER AUX SERVICES À LA CLIENTÈLE LIFETIME PRODUIT (il faut avoir les deux en entrant en contact avec nous) N° de modèle : 1044 Composer le 1-800-225-3865 Entretien en direct: www.lifetime.com/customerservice...
  • Page 3 (3.5" x 105"–3.5" x 112") (2 x 4 x 20 in) (x2) MODELO E ID DEL PRODUCTO ¿PREGUNTAS? PONERSE EN CONTACTO CON LOS SERVICIOS AL CLIENTE LIFETIME ® (se necesitan los dos al contactarnos) Número de modelo: 1044 Para nuestros servicios a clientes en el continente Marcar al 1-800-225-3865 Chat en vivo: www.lifetime.com/customerservice...
  • Page 4 ICON LEGEND / LÉGENDE DES ICÔNES / LEYENDA DE ÍCONOS • Indicates special heed should be taken when reading. • Ceci indique que vous devez faire attention à ce que vous lisez. • Indica que uno debe prestar atención al leer. •...
  • Page 5 WARNINGS & NOTICES / AVERTISSEMENTS ET AVIS / ADVERTENCIAS Y AVISOS / AVISOS Y NOTIFICAÇÕES SAFETY INSTRUCTIONS FAILURE TO FOLLOW THESE WARNINGS MAY RESULT IN SERIOUS INJURY OR PROPERTY DAMAGE AND WILL VOID WARRANTY. Owner must ensure that all players know and follow these rules for safe operation of the system. To ensure safety, do not attempt to assemble this product without following the instructions carefully.
  • Page 6 POLE-MOUNT ASSEMBLY /ASSEMBLAGE POUR LE MONTAGE AU POTEAU / ENSAMBLAJE PARA EL MONTAJE A UN POSTE HARDWARE REQUIRED / QUINCAILLERIE REQUISE / HERRAJE REQUERIDO Hardware bag / Sac de quincaillerie Bolsa de herraje BSF (x4) AAO (x1) APN (x4) AAA (x4) ABD (x2) APJ (x1) PARTS REQUIRED / PIÈCES REQUISES / PIEZAS REQUERIDAS...
  • Page 7 CONVERSION KIT TO POLE INSTALLATION / INSTALLATION DU KIT DE CONVERSION À UN POTEAU / INSTALACIÓN DEL KIT DE CONVERSIÓN A UN POSTE POLE MOUNT / MONTAGE À UN POTEAU / MONTAJE A UN POSTE • If you want to mount the conversoin kit to a pole, you’re in the right place. The mounting height for poles, indicated below, is 8' 1" (97") from the playing surface to the bottom of the rectangular mounting tube (included in this kit).

  • Page 8: Leyenda De Íconos

     SECTION 1 (CONTINUED) / SECTION 1 (SUITE) / SECCIÓN 1 (CONTINUACIÓN) TOOLS AND HARDWARE REQUIRED / OUTILS ET QUINCAILLERIE REQUIS / INSTRUMENTAL Y HERRAJE REQUERIDOS IMPORTANT! PLEASE READ / IMPORTANT ! VEILLER LIRE / ¡IMPORTANTE! FAVOR DE LEER • Unless the following steps are taken, a problem WILL ARISE if the pole to which you are mounting the conversion kit is taller than 9' 4" (112") (≈284,5 cm);...

  • Page 9: Advertencias Y Avisos

     SECTION 1 (CONTINUED) / SECTION 1 (SUITE) / SECCIÓN 1 (CONTINUACIÓN) TOOLS AND HARDWARE REQUIRED / OUTILS ET QUINCAILLERIE REQUIS / INSTRUMENTAL Y HERRAJE REQUERIDOS 1/2 in/po (≈13 mm) (x1) 1/2 in/po (≈13 mm) APJ (x1) (x1) AAO (x1) ABD (x2) IMPORTANT / IMPORTANTE •...

  • Page 10: Ensamblaje Du Combo Au Poteau

     SECTION 1 (CONTINUED) / SECTION 1 (SUITE) / SECCIÓN 1 (CONTINUACIÓN) TOOLS AND HARDWARE REQUIRED / OUTILS ET QUINCAILLERIE REQUIS / INSTRUMENTAL Y HERRAJE REQUERIDOS IMPORTANT / IMPORTANTE • The mounting height for poles is 8' 1" (97" (≈2,46 m) from the playing surface to the bottom of the rectangular mounting tube (FKE), shown below.
  • Page 11  SECTION 1 (CONTINUED) / SECTION 1 (SUITE) / SECCIÓN 1 (CONTINUACIÓN) TOOLS AND HARDWARE REQUIRED TOOLS AND HARDWARE REQUIRED / OUTILS ET QUINCAILLERIE REQUIS / OUTILS ET QUINCAILLERIE REQUIS / INSTRUMENTAL Y HERRAJE REQUERIDOS / INSTRUMENTAL Y HERRAJE REQUERIDOS 1/2 in/po (≈13 mm) 9/16 in/po (≈14 mm) (x1)
  • Page 12  SECTION 1 (CONTINUED) / SECTION 1 (SUITE) / SECCIÓN 1 (CONTINUACIÓN) TOOLS AND HARDWARE REQUIRED / OUTILS ET QUINCAILLERIE REQUIS / INSTRUMENTAL Y HERRAJE REQUERIDOS 9/16 in/po (≈14 mm) (x1) 1.5a FOR THOSE NOT USING THE HEIGHT STOP / POUR CEUX QUI N’UTILISENT PAS L’ARRÊT DE HAUTEUR / PARA LOS QUE NO UTILIZAN EL TOPE DE ALTURA •...
  • Page 13  SECTION 1 (CONTINUED) / SECTION 1 (SUITE) / SECCIÓN 1 (CONTINUACIÓN) TOOLS AND HARDWARE REQUIRED / OUTILS ET QUINCAILLERIE REQUIS / INSTRUMENTAL Y HERRAJE REQUERIDOS 9/16 in/po (≈14 mm) (x1) 1.5b FOR THOSE USING THE HEIGHT STOP / POUR CEUX QUI UTILISENT L’ARRÊT DE HAUTEUR / PARA LOS QUE UTILIZAN EL TOPE DE ALTURA •...
  • Page 14  SECTION 1 (CONTINUED) / SECTION 1 (SUITE) / SECCIÓN 1 (CONTINUACIÓN) TOOLS AND HARDWARE REQUIRED / OUTILS ET QUINCAILLERIE REQUIS / INSTRUMENTAL Y HERRAJE REQUERIDOS IMPORTANT / IMPORTANTE • There are three (3) types of backboards: Impact , Fusion and steel-frame.
  • Page 15 WALL-MOUNT ASSEMBLY / ASSEMBLAGE POUR LE MONTAGE AU MUR / ENSAMBLAJE PARA EL MONTAJE A MURO HARDWARE REQUIRED / QUINCAILLERIE REQUISE / HERRAJE REQUERIDO Hardware bag / Sac de quincaillerie Bolsa de herraje APJ (x1) BSF (x4) AAO (x1) ABD (x2) FKF (x4) APN (x4) PARTS REQUIRED / PIÈCES REQUISES / PIEZAS REQUERIDAS...
  • Page 16  SECTION 2 (CONTINUED) / SECTION 2 (SUITE) / SECCIÓN 2 (CONTINUACIÓN) TOOLS AND HARDWARE REQUIRED / OUTILS ET QUINCAILLERIE REQUIS / INSTRUMENTAL Y HERRAJE REQUERIDOS IMPORTANT! PLEASE READ / IMPORTANT ! VEILLER LIRE / ¡IMPORTANTE! FAVOR DE LEER • If you want to mount the conversoin kit to a wall, you’re in the right place. Unless the following steps are taken, A PROBLEM WILL ARISE if the wall to which you are mounting the conversion kit is higher than 9'2"...
  • Page 17  SECTION 2 (CONTINUED) / SECTION 2 (SUITE) / SECCIÓN 2 (CONTINUACIÓN) TOOLS AND HARDWARE REQUIRED / OUTILS ET QUINCAILLERIE REQUIS / INSTRUMENTAL Y HERRAJE REQUERIDOS 1/2 in/po (≈13 mm) (x1) 1/2 in/po (≈13 mm) APJ (x1) (x1) AAO (x1) ABD (x2) •...
  • Page 18  SECTION 2 (CONTINUED) / SECTION 2 (SUITE) / SECCIÓN 2 (CONTINUACIÓN) TOOLS AND HARDWARE REQUIRED / OUTILS ET QUINCAILLERIE REQUIS / INSTRUMENTAL Y HERRAJE REQUERIDOS 1/4" (≈6,35 mm) 2 in/po x 4 in/po x 20 in/po (x2) WALL MOUNT / MONTAGE À UN MUR / MONTAJE A UN MURO •...

  • Page 19: Ensamblaje Du Du Combo Au Mur

     SECTION 2 (CONTINUED) / SECTION 2 (SUITE) / SECCIÓN 2 (CONTINUACIÓN) TOOLS AND HARDWARE REQUIRED / OUTILS ET QUINCAILLERIE REQUIS / INSTRUMENTAL Y HERRAJE REQUERIDOS 1/2 in/po (≈13 mm) (x1) BSF (x4) 1/2 in/po (≈13 mm) (x1) APN (x4) •...
  • Page 20  SECTION 2 (CONTINUED) / SECTION 2 (SUITE) / SECCIÓN 2 (CONTINUACIÓN) TOOLS AND HARDWARE REQUIRED / OUTILS ET QUINCAILLERIE REQUIS / INSTRUMENTAL Y HERRAJE REQUERIDOS 9/16" (≈14 mm) FKF (x4) • IMPORTANT: for the rim to be at the regulation 10' (≈3 m) height when the system is at its highest position (when NOT using the “Height Stop,”...
  • Page 21  SECTION 2 (CONTINUED) / SECTION 2 (SUITE) / SECCIÓN 2 (CONTINUACIÓN) TOOLS AND HARDWARE REQUIRED / OUTILS ET QUINCAILLERIE REQUIS / INSTRUMENTAL Y HERRAJE REQUERIDOS IMPORTANT / IMPORTANTE • There are three (3) types of backboards: Impact , Fusion and steel-frame.
  • Page 22 IMPACT COMBO ASSEMBLY / ASSEMBLAGE DU COMBO IMPACT / ENSAMBLAJE DEL COMBO IMPACT ® ® ® HARDWARE REQUIRED / QUINCAILLERIE REQUISE / HERRAJE REQUERIDO From conversion kit / Du kit de conversion / Del kit de conversión • not used with Impact models ®...

  • Page 23: Combo Assembly

    IMPACT COMBO ASSEMBLY / ASSEMBLAGE DU COMBO IMPACT / ENSAMBLAJE DEL COMBO IMPACT ® ® ® PARTS REQUIRED / PIÈCES REQUISES / PIEZAS REQUERIDAS Metal parts / Pièces en métal Piezas de metal Conversion kit / Kit de conversion / Kit de conversión Combo Kit / Kit combiné...
  • Page 24  SECTION 3 (CONTINUED) / SECTION 3 (SUITE) SECCIÓN 3 (CONTINUACIÓN) TOOLS AND HARDWARE REQUIRED / OUTILS ET QUINCAILLERIE REQUIS INSTRUMENTAL Y HERRAJE REQUERIDOS 7/16 in/po (≈11 mm) ABS (x2) (x1) 1/4 x 2 3/4 in/po (≈6 mm x 7 cm) 7/16 in/po (≈11 mm) APK (x1) (x1)
  • Page 25  SECTION 3 (CONTINUED) / SECTION 3 (SUITE) SECCIÓN 3 (CONTINUACIÓN) TOOLS AND HARDWARE REQUIRED / OUTILS ET QUINCAILLERIE REQUIS INSTRUMENTAL Y HERRAJE REQUERIDOS 1/2 in/po (≈13 mm) (x1) ABK (x2) ABD (x2) Impact backboard and rim assembly ® • Set a rim support channel (AOX) into the recess in the back of the backboard. The ends of the U-bolt should go through the backboard and rim.

  • Page 26: Ensamblaje Du Combo Impact

     SECTION 3 (CONTINUED) / SECTION 3 (SUITE) SECCIÓN 3 (CONTINUACIÓN) TOOLS AND HARDWARE REQUIRED / OUTILS ET QUINCAILLERIE REQUIS INSTRUMENTAL Y HERRAJE REQUERIDOS 1/2 in/po (≈13 mm) (x1) AAC (x2) ABK (x2) ABD (x2) Impact backboard and rim assembly ®...
  • Page 27  SECTION 3 (CONTINUED) / SECTION 3 (SUITE) SECCIÓN 3 (CONTINUACIÓN) TOOLS AND HARDWARE REQUIRED / OUTILS ET QUINCAILLERIE REQUIS INSTRUMENTAL Y HERRAJE REQUERIDOS 1/2 in/po (≈13 mm) (x1) APJ (x2) AAJ (x2) • Bend the backboard brackets outward and align the hole in each end with the holes in the backboard as indicated. •...
  • Page 28  SECTION 3 (CONTINUED) / SECTION 3 (SUITE) SECCIÓN 3 (CONTINUACIÓN) TOOLS AND HARDWARE REQUIRED / OUTILS ET QUINCAILLERIE REQUIS INSTRUMENTAL Y HERRAJE REQUERIDOS • Fold the outer guard (BDN) and set the dunk latch (BDL) into it. • Plier le outer guard (BDN) et mettre le loquet de dunk (BDL) in it. •...
  • Page 29  SECTION 3 (CONTINUED) / SECTION 3 (SUITE) SECCIÓN 3 (CONTINUACIÓN) TOOLS AND HARDWARE REQUIRED / OUTILS ET QUINCAILLERIE REQUIS INSTRUMENTAL Y HERRAJE REQUERIDOS 3/4 in/po (≈19 mm) (x2) 1/2 x 7 1/16 in/po AAX (x1) ABL (x2) AAD (x1) •...
  • Page 30  SECTION 3 (CONTINUED) / SECTION 3 (SUITE) SECCIÓN 3 (CONTINUACIÓN) TOOLS AND HARDWARE REQUIRED / OUTILS ET QUINCAILLERIE REQUIS INSTRUMENTAL Y HERRAJE REQUERIDOS 3/8 x 7 in/po 3/4 in/po (≈19 mm) ABL (x2) (x2) AQW (x1) ABB (x1) 9/16 in/po (≈14 mm) (x2) 1/2 x 7 1/16 in/po AAX (x1)

  • Page 31: Combo Assembly

    FUSION COMBO ASSEMBLY / ASSEMBLAGE DU COMBO FUSION / ENSAMBLAJE DEL COMBO FUSION ® ® ® HARDWARE REQUIRED / QUINCAILLERIE REQUISE / HERRAJE REQUERIDO HARDWARE REQUIRED / QUINCAILLERIE REQUISE / HERRAJE REQUERIDO From conversion kit / Du kit de conversion / Del kit de conversión AAB (x2)
  • Page 32 FUSION COMBO ASSEMBLY / ASSEMBLAGE DU COMBO FUSION / ENSAMBLAJE DEL COMBO FUSION ® ® ® PARTS REQUIRED / PIÈCES REQUISES / PIEZAS REQUERIDAS Metal parts / Pièces en métal Piezas de metal AKC (x4) BDL (x1) AJK (x1) AJJ (x1) Plastic parts / Pièces en plastique / Piezas de plástico...
  • Page 33  SECTION 4 (CONTINUED) / SECTION 4 (SUITE) SECCIÓN 4 (CONTINUACIÓN) TOOLS AND HARDWARE REQUIRED / OUTILS ET QUINCAILLERIE REQUIS INSTRUMENTAL Y HERRAJE REQUERIDOS 7/16 in/po (≈11 mm) (x1) ABS (x2) (x1) (Not to scale) (Non à l’échelle) (No está a la escala) 7/16 in/po (≈11 mm) (x1) AAB (x2)
  • Page 34  SECTION 4 (CONTINUED) / SECTION 4 (SUITE) SECCIÓN 4 (CONTINUACIÓN) TOOLS AND HARDWARE REQUIRED / OUTILS ET QUINCAILLERIE REQUIS INSTRUMENTAL Y HERRAJE REQUERIDOS 1/2 in/po (≈13 mm) (x1) ABG (x2) AAJ (x2) ABD (x2) ABF (x2) • Slide two (2) washers (ABD) and two (2) rubber washers (ABF) over two (2) bolts (ABG) and insert the bolts up through the holes in the rim (ALX), as indicated.

  • Page 35: Ensamblaje Du Combo Fusion

     SECTION 4 (CONTINUED) / SECTION 4 (SUITE) SECCIÓN 4 (CONTINUACIÓN) TOOLS AND HARDWARE REQUIRED / OUTILS ET QUINCAILLERIE REQUIS INSTRUMENTAL Y HERRAJE REQUERIDOS 1/2 in/po (≈13 mm) (x1) AOX (x1) (Not to scale) AAV (x2) (Non à l’échelle) ABK (x2) (No está...
  • Page 36  SECTION 4 (CONTINUED) / SECTION 4 (SUITE) SECCIÓN 4 (CONTINUACIÓN) TOOLS AND HARDWARE REQUIRED / OUTILS ET QUINCAILLERIE REQUIS INSTRUMENTAL Y HERRAJE REQUERIDOS AJW (x2) AOW (x1) • Slide one (1) compression spring (AJW) over each end of the U-bolt. •...
  • Page 37  SECTION 4 (CONTINUED) / SECTION 4 (SUITE) SECCIÓN 4 (CONTINUACIÓN) TOOLS AND HARDWARE REQUIRED / OUTILS ET QUINCAILLERIE REQUIS INSTRUMENTAL Y HERRAJE REQUERIDOS 1/2 in/po (≈13 mm) (x1) ABK (x2) • Secure the retainer plate with two (2) tuercas (ABK). Tighten only until the rim doesn’t wobble. •...
  • Page 38  SECTION 4 (CONTINUED) / SECTION 4 (SUITE) SECCIÓN 4 (CONTINUACIÓN) TOOLS AND HARDWARE REQUIRED / OUTILS ET QUINCAILLERIE REQUIS INSTRUMENTAL Y HERRAJE REQUERIDOS 3/8 in/po (≈10 mm) (x1) ADQ (x2) 4.10 • Secure the backboard brackets to the backboard using two (2) screws (ADQ).
  • Page 39 PARTS IDENTIFIER / IDENTIFICATEUR DE PIÈCES / IDENTIFICADOR DE PIEZAS CONVERSION KIT PARTS / PIÈCES DU KIT DE CONVERSION / PIEZAS DEL KIT DE CONVERSIÓN Large parts / Grandes pièces Piezas grandes AKC (x4) BDL (x1) AJK (x1) AJJ (x1) AKP (x1) BNP (x1) AMT (x1)
  • Page 40 PARTS IDENTIFIER / IDENTIFICATEUR DE PIÈCES / IDENTIFICADOR DE PIEZAS COMBO KIT PARTS / PIÈCES DU KIT COMBINÉ / PIEZAS DEL KIT COMBINADO Large parts / Grandes pièces Piezas grandes AJI Impact (x1) ® AJI (x1) Fusion ® AJI Steel-framed / Cadre en acier Aramzón de acero (x1)
  • Page 41 PARTS IDENTIFIER / IDENTIFICATEUR DE PIÈCES / IDENTIFICADOR DE PIEZAS COMBO KIT HARDWARE / QUINCAILLERIE DU KIT COMBINÉ / HERRAJE DEL KIT COMBINADO For rim and Impact backboards / Pour l’anneau et panneaux Impact Para los tableros Impact y aros ®...
  • Page 42 PARTS IDENTIFIER / IDENTIFICATEUR DE PIÈCES / IDENTIFICADOR DE PIEZAS COMBO KIT HARDWARE / QUINCAILLERIE DU KIT COMBINÉ / HERRAJE DEL KIT COMBINADO For rims and steel-framed backboards / Pour les panneaux de cadre en acier et les anneaux Para los tableros de armazón de acero y aros METAL-FRAMED BACKBOARD 90718 ABC (x2) AAV (x2)
  • Page 43  SECTION 4 (CONTINUED) / SECTION 4 (SUITE) SECCIÓN 4 (CONTINUACIÓN) TOOLS AND HARDWARE REQUIRED / OUTILS ET QUINCAILLERIE REQUIS INSTRUMENTAL Y HERRAJE REQUERIDOS 4.12 • Slide the end of the Quick Adjust mechanism between the inner guard and align the holes as indicated. The outer guard goes ®...
  • Page 44  SECTION 4 (CONTINUED) / SECTION 4 (SUITE) SECCIÓN 4 (CONTINUACIÓN) TOOLS AND HARDWARE REQUIRED / OUTILS ET QUINCAILLERIE REQUIS INSTRUMENTAL Y HERRAJE REQUERIDOS 7 1/16 in/po (≈17,9 cm) 7 in/po (≈17,8 cm) 3/4 in/po (≈19 mm) (x2) 9/16 in/po (≈14 mm) (x2) AQW (x1) AAD (x2)

  • Page 45: Ensamblaje Du Combo De Armazón De Acero

    STEEL-FRAME COMBO ASSEMBLY / ASSEMBLAGE DU COMBO CADRE EN ACIER / ENSAMBLAJE DEL ARMAZÓN DE ACERO PARTS REQUIRED / PIÈCES REQUISES / PIEZAS REQUERIDAS Metal parts / Pièces en métal Piezas de metal Conversion kit / Kit de conversion Kit de conversión AKC (x4) BDL (x1) AJK (x1)
  • Page 46 STEEL-FRAME COMBO ASSEMBLY / ASSEMBLAGE DU COMBO CADRE EN ACIER / ENSAMBLAJE DEL ARMAZÓN DE ACERO CONVERSION KIT HARDWARE REQUIRED / QUINCAILLERIE REQUISE DU KIT DE CONVERSION / HERRAJE REQUERIDO DEL KIT DE CONVERSIÓN AQW (x1) AAD (x2) ABS (x2) AAS (x2) APX (x2) AAB (x2)
  • Page 47 STEEL-FRAME COMBO ASSEMBLY / ASSEMBLAGE DU COMBO CADRE EN ACIER / ENSAMBLAJE DEL ARMAZÓN DE ACERO • Two types of rim hardware come with the steel-framed backboard & rim combo kits: that for the Slam-It rim and that for the Slam-It Pro rim.
  • Page 48 STEEL-FRAME COMBO ASSEMBLY / ASSEMBLAGE DU COMBO CADRE EN ACIER / ENSAMBLAJE DEL ARMAZÓN DE ACERO HARDWARE REQUIRED (SLAM-IT PRO) / QUINCAILLERIE REQUISE (SLAM-IT PRO) / ® ® HERRAJE REQUERIDO (SLAM-IT PRO) ® AAM (x2) ABC (x2) (Not used with Slam-It Pro rim) ®...
  • Page 49  SECTION 5 (CONTINUED) / SECTION 5 (SUITE) SECCIÓN 5 (CONTINUACIÓN) TOOLS AND HARDWARE REQUIRED / OUTILS ET QUINCAILLERIE REQUIS INSTRUMENTAL Y HERRAJE REQUERIDOS 1/2 in/po (≈13 mm) (x1) AAM (x2) AAR (x2) ABD (x2) ABF (x2) ABQ (x1) APY (x1) AAQ (x1) Metal-frame backboard—will have one of two types of rims: Slam-it or Slam-it...
  • Page 50  SECTION 5 (CONTINUED) / SECTION 5 (SUITE) SECCIÓN 5 (CONTINUACIÓN) TOOLS AND HARDWARE REQUIRED / OUTILS ET QUINCAILLERIE REQUIS INSTRUMENTAL Y HERRAJE REQUERIDOS 1/2 in/po (≈13 mm) (x1) AAJ (x2) • Slide the pivot assembly into the housing of the Slam-It Pro rim (ALX) and align the holes as indicated.
  • Page 51  SECTION 5 (CONTINUED) / SECTION 5 (SUITE) SECCIÓN 5 (CONTINUACIÓN) TOOLS AND HARDWARE REQUIRED / OUTILS ET QUINCAILLERIE REQUIS INSTRUMENTAL Y HERRAJE REQUERIDOS 1/2 in/po (≈13 mm) (x1) AAQ (x1) • Use the 1/2 in/po (≈13 mm) socket to press the second push nut (AAQ) 1/4 in/po (≈6,4 mm) onto the other end of the axle to lock the pin in place.
  • Page 52  SECTION 5 (CONTINUED) / SECTION 5 (SUITE) SECCIÓN 5 (CONTINUACIÓN) TOOLS AND HARDWARE REQUIRED / OUTILS ET QUINCAILLERIE REQUIS INSTRUMENTAL Y HERRAJE REQUERIDOS 3/8 in/po (≈10 mm) ABS (x2) (x1) 3/8 in/po (≈10 mm) (x1) AAB (x2) AAS (x2) •...
  • Page 53  SECTION 5 (CONTINUED) / SECTION 5 (SUITE) SECCIÓN 5 (CONTINUACIÓN) TOOLS AND HARDWARE REQUIRED / OUTILS ET QUINCAILLERIE REQUIS INSTRUMENTAL Y HERRAJE REQUERIDOS 1/2 in/po (≈13 mm) (x2) ACS (x2) ABK (x2) • Insert the two rim bolts up through the holes in the backboard. Slide one (1) spacer (ACS) over each bolt. Set the backboard bracket assembly onto the backboard, the ends of the u-bolt through the holes.
  • Page 54  SECTION 5 (CONTINUED) / SECTION 5 (SUITE) SECCIÓN 5 (CONTINUACIÓN) TOOLS AND HARDWARE REQUIRED / OUTILS ET QUINCAILLERIE REQUIS INSTRUMENTAL Y HERRAJE REQUERIDOS 1/2 in/po (≈13 mm) (x1) AAV (x2) AJW (x2) 5.10 • Tighten the two (2) jam nuts (ABI) onto the U-bolt as far as they will go. •...
  • Page 55  SECTION 5 (CONTINUED) / SECTION 5 (SUITE) SECCIÓN 5 (CONTINUACIÓN) TOOLS AND HARDWARE REQUIRED / OUTILS ET QUINCAILLERIE REQUIS INSTRUMENTAL Y HERRAJE REQUERIDOS 1/2 in/po (≈13 mm) (x1) ABK (x2) AOW (x1) 5.12 • Set the spring retainer plate (AOW) over the two bolts. •...
  • Page 56  SECTION 5 (CONTINUED) / SECTION 5 (SUITE) SECCIÓN 5 (CONTINUACIÓN) TOOLS AND HARDWARE REQUIRED / OUTILS ET QUINCAILLERIE REQUIS INSTRUMENTAL Y HERRAJE REQUERIDOS APX (x2) 5.14 • Slide a bolt (APX) under the ridges in each groove in the back of the backboard. •...
  • Page 57  SECTION 5 (CONTINUED) / SECTION 5 (SUITE) SECCIÓN 5 (CONTINUACIÓN) TOOLS AND HARDWARE REQUIRED / OUTILS ET QUINCAILLERIE REQUIS INSTRUMENTAL Y HERRAJE REQUERIDOS 1/2 in/po (≈13 mm) (x1) ADR (x4) ABK (x2) 5.16 • Secure the backboard brackets to the backboard using two (2) nuts (ABK). •...
  • Page 58  SECTION 5 (CONTINUED) / SECTION 5 (SUITE) SECCIÓN 5 (CONTINUACIÓN) TOOLS AND HARDWARE REQUIRED / OUTILS ET QUINCAILLERIE REQUIS INSTRUMENTAL Y HERRAJE REQUERIDOS 5.18 • Fold the outer guard (BDN) and set the dunk latch (BDL) into it. • Plier le outer guard (BDN) et mettre le loquet de dunk (BDL) in it. •...
  • Page 59  SECTION 5 (CONTINUED) / SECTION 5 (SUITE) SECCIÓN 5 (CONTINUACIÓN) TOOLS AND HARDWARE REQUIRED / OUTILS ET QUINCAILLERIE REQUIS INSTRUMENTAL Y HERRAJE REQUERIDOS 7 1/16 in/po (≈17,9 cm) AAD (x1) ABL (x1) 5.19 • Place one of the four extension arms (AKC) against the backboard bracket with a spacer (ABL) between them. Insert a bolt (AAD) through the extension arm and spacer.
  • Page 60  SECTION 5 (CONTINUED) / SECTION 5 (SUITE) SECCIÓN 5 (CONTINUACIÓN) TOOLS AND HARDWARE REQUIRED / OUTILS ET QUINCAILLERIE REQUIS INSTRUMENTAL Y HERRAJE REQUERIDOS 3/4 in/po (≈19 mm) (x2) ABL (x1) AAX (x1) 5.20 • Slide a spacer (ABL) and another extension arm (AKC) over the bolt. Secure with one (1) nut (AAX). Tighten the nut until it is fl ush with the end of the bolt.
  • Page 61  SECTION 5 (CONTINUED) / SECTION 5 (SUITE) SECCIÓN 5 (CONTINUACIÓN) TOOLS AND HARDWARE REQUIRED / OUTILS ET QUINCAILLERIE REQUIS INSTRUMENTAL Y HERRAJE REQUERIDOS 7 1/16 in/po (≈17,9 cm) 3/4 in/po (≈19 mm) (x2) 9/16 in/po (≈14 mm) (x2) 7 in/po (≈17,8 cm) AAD (x1) AAX (x1) ABB (x1)
  • Page 62  SECTION 5 (CONTINUED) / SECTION 5 (SUITE) SECCIÓN 5 (CONTINUACIÓN) TOOLS AND HARDWARE REQUIRED / OUTILS ET QUINCAILLERIE REQUIS INSTRUMENTAL Y HERRAJE REQUERIDOS ADP (x10) 5.22 • Peel the plastic fi lm off the front of the backboard. • Peler le fi lm plastique de la face avant du panneau. •...
  • Page 63  SECTION 5 (CONTINUED) / SECTION 5 (SUITE) SECCIÓN 5 (CONTINUACIÓN) TOOLS AND HARDWARE REQUIRED / OUTILS ET QUINCAILLERIE REQUIS INSTRUMENTAL Y HERRAJE REQUERIDOS ADP (x6) 5.24 • Secure the left and right corner frame pads (BAA and BAB) to the bottom of the frame, overlapping the center frame pad.

  • Page 64: Pole Installation

    POLE INSTALLATION / INSTALLATION AU POTEAU / INSTALACIÓN AL POSTE HARDWARE REQUIRED / QUINCAILLERIE REQUISE / HERRAJE REQUERIDO Hardware bag / Sac de quincaillerie / Bolsa de herraje 1/2 x 7 1/16 in/po (13 mm x 17,9 cm) AAD (x2) FKG (x4) AAX (x2) TOOLS REQUIRED / OUTILS REQUIS / INSTRUMENTAL REQUERIDO...
  • Page 65  SECTION 6 (CONTINUED) / SECTION 6 (SUITE) SECCIÓN 6 (CONTINUACIÓN) TOOLS AND HARDWARE REQUIRED / OUTILS ET QUINCAILLERIE REQUIS INSTRUMENTAL Y HERRAJE REQUERIDOS 1/2 x 7 1/16 in/po (13 mm x 17,9 cm) 3/4 in/po (≈19 mm) (x2) AAD (x2) AAX (x2) FKG (x4) •...

  • Page 66: Wall Installation

    WALL INSTALLATION / INSTALLATION AU MUR / INSTALACIÓN AL MURO HARDWARE REQUIRED / QUINCAILLERIE REQUISE / HERRAJE REQUERIDO Hardware bag / Sac de quincaillerie / Bolsa de herraje 1/2 x 7 1/16 in/po (13 mm x 17,9 cm) AAD (x2) FKG (x4) AAX (x2) TOOLS REQUIRED / OUTILS REQUIS / INSTRUMENTAL REQUERIDO...
  • Page 67  SECTION 7 (CONTINUED) / SECTION 7 (SUITE) SECCIÓN 7 (CONTINUACIÓN) TOOLS AND HARDWARE REQUIRED / OUTILS ET QUINCAILLERIE REQUIS INSTRUMENTAL Y HERRAJE REQUERIDOS 3/4 in/po (≈19 mm) (x2) 1/2 x 7 1/16 in/po (13 mm x 17,9 cm) AAX (x2) AAD (x2) FKG (x4) •...
  • Page 68 ADJUSTMENT / AJUSTEMENTE / AJUSTO OPERATION OF THE QUICK ADJUST II SYSTEM ® The QUICK ADJUST II system is adjustable from 7.5' to 10' in 6" increments. ® To Raise the Goal: Place the end of a broom stick under the rim plate and push up until the desired height is reached The system will automatically lock into place.

  • Page 69: Maintenance

    MAINTENANCE / ENTRETIEN / MANTENIMIENTO The life of this basketball system depends on many variables. The climate, exposure to corrosives such as salt, pesticides, or herbicides, and excessive use or misuse can all contribute to system failure, which may cause property damage or personal injury. Check your basketball system frequently for loose hardware, excessive wear, and signs of corrosion.

  • Page 70: Warning Sticker

    Son mécanisme a été conçu uniquement pour soutenir le poids du panneau et de l’anneau. N’accrochez rien au manche, à l’anneau, au panneau ni aux leviers sous peine d’endommager l’équipement et d’annuler la garantie. Lifetime Products, Inc., Clearfield, UT 84016 www.lifetime.com 7/12/2016 # 1176611...
  • Page 71 NOTES / REMARQUES / NOTAS...

  • Page 72: Registration

    ® À Lifetime , l’entretien de ta confi dentialité est notre politique de longue date. Et tu peux être sûr que Lifetime ne vendra pas ni fournira pas tes données personnelles à d’autres tiers, ou les permettra d’utiliser tes données personnelles à leur propres fi ns.
  • Page 73 2. This warranty is nontransferable and is expressly limited to the repair or replacement of defective product. If the product is defective within the terms of this warranty, Lifetime Products, Inc. will repair or replace defective parts at no cost to the purchaser.
  • Page 74 6. Cette garantie remplace expressément toutes autres garanties, expresses ou tacites, y compris les garanties de commercialisation ou d’adaptation à un but particulier dans la mesure permise par les lois fédéraux et des états. Ni Lifetime Products, Inc. ni aucun de ses représentants n’assure aucune autre responsabilité concernant ce produit. Cette garantie vous accorde des droits particuliers, et vous aurai peut-être des autres droites qui varient d’un état à...

  • Page 75: Garantía

    NO ESTÁN DISPONIBLES O SON OBSOLETAS. 1. El comprador original recibe la garantía de que los sistemas de basquetbol Lifetime estarán libres de defectos de material o de mano de obra por un período de cinco años a contar desde la fecha de la compra original. La palabra “defectos” se define como imperfecciones que perjudican el uso del producto.
  • Page 76 1-800-424-3865 7:00 am–5:00 pm (M–F) MST and 9:00 am–1:00 pm Saturday MST As someone who has experienced a Lifetime product, your voice holds a lot of power. Whether you absolutely love your product or want to suggest improvements, your review will make a di erence.

Table of Contents