BWS-T4 Series
7. OPERATING PROCEDURES
7.1.
DIP-SWITCHES CONFIGURATION
The configuration indicated in table must be selected on both the dip-
switch present on the side of the control unit, after to have removed the
cap of protection. The description corresponding to the pre-choosen
selection is reported.
1
function
X
not used
2
function
muting A-B act on the sensor couples 1
Off
and 2.
muting C-D act on the sensor couples 3
and 4.
On
muting A-B act on the sensor couple 1.
muting C-D act on the sensor couple 2.
The sensor couples 3-4 continue to
function normally.
3
function
Off
muting 60 s
On
muting ∞ s
The control-unit is manufactured from the factory with the following
configuration:
•
Automatic restoring, all four optics in muting, the maximum
duration of the muting is of sixteen seconds.
7.2.
CONFIGURATION OF THE NUMBER OF PHOTOCELLS
In case you use a number of photocells which is lower than 4, operate
as follows: to disconnect the photocells do not use and therefore do not
connect to the control unit; carry out a connection among the following
terminals:
unused photocell
1
2
3
4
At least one pair of photocells must be connected, otherwise (condition
of all the disconnected photocells) the control unit is locked.
Instructions manual
SW 1
SW 2
O N
4
1
2
3
3
2
1
4
ON
NOT E: configure the two dip-
switch in the sam e waj,otherwise
the central control unit is locked
and code '8' is displayed.
4
function
Off
manual restoring
On
automatic restoring
connection
19 to 27
20 to 28
23 to 31
24 to 32
12
Serie BWS-T4
7. PROCEDURE OPERATIVE
7.1.
CONFIGURAZIONE DEI DIP-SWITCH.
La configurazione indicata in tabella deve essere selezionata su
entrambi i dip-switch presenti sul fianco della centralina, dopo aver
asportato
il
tappo
di
protezione:
corrispondente alla selezione prescelta:
1
funzione
X
non utilizzato
2
funzione
muting A-B agiscono sulle coppie di
Off
sensori 1 e 2
muting C-D agiscono sulle coppie di
sensori 3 e 4
muting A-B agiscono sulla coppia di
On
sensori 1
muting C-D agiscono sulla coppia di
sensori 2
le coppie di sensori 3-4 continuano
ad operare normalmente
3
funzione
Off
muting 60 s
On
muting ∞ s
La centralina esce dalla fabbrica configurata nel seguente modo:
•
Ripristino automatico, tutte 4 le ottiche in muting, durata
massima del muting di 60 secondi.
7.2.
CONFIGURAZIONE DEL NUMERO DI FOTOCELLULE
In caso di utilizzo di un numero di fotocellule inferiore a 4 agire come
segue:
per escludere le fotocellule non utilizzate e quindi non collegate
all'unità di controllo fare un collegamento tra i seguenti morsetti:
fotocellula non utilizzata
1
2
3
4
Manuale istruzioni
si
riporta
la
descrizione
SW1
SW2
ON
4
1
2
3
3
2
1
4
ON
NOTA BENE: configurare i due
dip-switch nello stesso modo, in
caso contrario la centralina andrà
in blocco visualizzando il codice '8'
sul display.
4
funzione
Off
ripristino manuale
On
ripristino automatico
collegamento
19 con 27
20 con 28
23 con 31
24 con 32
12