Advertisement
Quick Links
Hertford - 3 Door Robe
Assembly Instructions -
Dimensions
Width - 125.5cm
Depth - 49cm
Height - 194cm
Important -
Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, call the Customer Helpline: 03456 400800
Please keep for future reference
346/3390
357/4533
MADE IN
BRITAIN
Issue 3 - 28/01/15
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Heart of House Hertford 346/3390
Summary of Contents for Heart of House Hertford 346/3390
- Page 1 Hertford - 3 Door Robe Assembly Instructions - 346/3390 Please keep for future reference 357/4533 Dimensions Width - 125.5cm Depth - 49cm MADE IN Height - 194cm BRITAIN Important - Please read these instructions fully before starting assembly If you need help or have damaged or missing parts, call the Customer Helpline: 03456 400800 Issue 3 - 28/01/15...
-
Page 2: Care And Maintenance
Safety and Care Advice Important - Please read these instructions fully before starting assembly • Warning: This unit weighs • Make sure you have enough • We do not approximately 80kgs. space to layout the parts before recommend the Please lift with care. starting. - Page 3 If you have damaged or missing components, call the Components - Panels Customer Helpline: 03456 400800 quoting the reference numbers below Please check you have all the panels listed below (DF370) (1185 x 482mm) Base (DF371) (1185 x 463mm) Left Side Right Side Divider Rail...
- Page 4 If you have damaged or missing components, call the Components - Fittings Customer Helpline: 03456 400800 quoting the reference numbers below Please check you have all the fittings listed below Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required.
- Page 5 If you have damaged or missing components, call the Assembly Instructions Customer Helpline: 03456 400800 quoting the reference numbers below Step 1 Start preparing the divider Please refer to the drawings opposite. You have a choice of 2 positions to fit the large shelf.
- Page 6 Assembly Instructions Step 2 Finish preparing the divider Screw a metal dowel into the divider Finished Note: Tighten the metal front edge dowels up fully against the panels. Fit 4 hinge plates onto Turn the divider over the divider , making sure that the slot is facing towards the finished front edge.
- Page 7 Assembly Instructions Step 4 Fit top and base to the right side Note: The top is 482mm Attach the top to the deep and the base is divider using 2 463mm deep. screws Attach the base the divider using 2 screws Finished front edge...
- Page 8 Assembly Instructions Step 6 Fit the right side Push the right side onto the top base Use a screwdriver to tighten the 2 large locking nuts fitted to the top and the 2 fitted to the base Note: Turn the large locking nuts as far as they will go - more than...
- Page 9 Assembly Instructions Step 8 Prepare the left side Fit 1 or 2 rail holders into the same position as you did in step 1 for the Finished divider. front edge To fit the rail holder screw through the top hole with screw into the mark hole drilled in the left side .
- Page 10 Assembly Instructions Step 9 Fit the rail Push the rail onto the divider Use a screwdriver to Finished tighten the large locking front edge fitted to the rail Note: Support the rail until the left side has been fitted in the next step. Step 10 Fit the left side Push the left side...
- Page 11 Assembly Instructions Step 11 The measurement from top corner X to bottom corner X must be equal to the measurement from top corner Y to bottom corner Y Fit the back panels Square up the unit by making sure that measurement x:x equals y:y.
- Page 12 Assembly Instructions Step 12 Fit the hanging rails Push the small hanging rail and large hanging rail(s) into the rail holders fitted to the panels. Note: You may have chosen different large hanging rail positions to the ones shown. Step 13 Fit the shelf studs Insert 4 shelf studs each shelf.
- Page 13 Assembly Instructions Step 14 Fit the shelves Lower the large shelf and small shelf down onto the shelf studs Note: You may have chosen a different position for the large shelf to the one shown. Step 15 Prepare the 3 doors Push fit 4 hinges into each of the 3 doors...
- Page 14 Assembly Instructions Step 16 Fit doors and handles Note: The easiest way to attach each door is to fit the top hinge first, then align and fit the other hinges. Push the hinge onto the front part of the hinge plate The recess at the bottom of screw B goes into the slot in the hinge plate.
- Page 15 Assembly Instructions Step 17 Adjust the doors if needed Before adjusting the doors, use a spirit level to check the base (or top) of the unit is level, front-to-back and side-to-side in the 3 positions shown. Use suitable packing pieces (not supplied) to make the unit level BEFORE making any adjustment to the hinges,...
- Page 16 Assembly Instructions Step 18 Screw Fit the overbalance Washer protector Wall fixing Strap (not supplied) Strap To prevent possible Washer overbalancing we recommend that this unit Screw is secured to a suitable (not supplied) wall by fitting of the overbalance protector kit to the unit, or an alternative fixing method of your choice.
Need help?
Do you have a question about the Hertford 346/3390 and is the answer not in the manual?
Questions and answers