Risk Levels; Children And Bystanders; Electrical - GreenWorks DHA103 Operator's Manual

EN
Symbol Name
DANGER ---
Keep Hands
and Feet Away
DANGER ---
Keep Bystand-
ers Away
DANGER ---
Thrown Debris
DANGER ---
Steep Slope
Hazard
DANGER ---
Keep Feet
Away
2.3

RISK LEVELS

The following signal words and meanings are intended to
explain the levels of risk associated with this product.
SYM- SIGNAL
BOL
DANGER
WARNING
CAUTION
CAUTION
2.4

CHILDREN AND BYSTANDERS

Tragic accidents can occur if the operator is not alert to the
presence of children or bystanders.
• Keep the area of operation clear of all persons,
particularly small children, and pets.
• Use extreme care when approaching blind corners,
doorways, shrubs, trees, or other objects that may obscure
your vision of a child or bystander. Keep children,
bystanders, helpers and pets at least 100 feet (30m) from
Explanation
To reduce the risk of injury,
keep hands and feet away from
rotating parts. Do not operate
unless discharge cover or grass
bag is in its proper place. If
damaged, replace immediately.
All visitors should be kept at a
distance from work area.
Remove objects that can be
thrown by the blade in any di-
rection. Wear safety glasses.
Use extra caution on slopes. do
not mow slopes greater than 15
degrees.
Keep feet away from the rotat-
ing cylinder.
MEANING
Indicates an imminently haz-
ardous situation, which, if not
avoided, will result in death
or serious injury.
Indicates a potentially hazard-
ous situation, which, if not
avoided, could result in death
or serious injury.
Indicates a potentially hazard-
ous situation, which, if not
avoided, may result in minor
or moderate injury.
(Without Safety Alert Sym-
bol) Indicates a situation that
may result in property dam-
age.
English
the mower while it is in operation. Stop the machine if
anyone enters the area.
• Never allow children under 14 years old to operate a
power mower. Operators 14 years old and over should
fully read and understand the operator's manual and
safety rules. Only responsible individuals who are
familiar with these rules of safe operation should be
allowed to use this machine.
2.5

ELECTRICAL

The double insulated system is intended to protect the user
from shock resulting from a break in the tool's internal
insulation. Observe all normal safety precautions to avoid
electrical shock.
Electrical connection
This product has a precision-built electric motor. It should be
connected to a power supply that is 120 V, AC only (normal
household current), 60 Hz. Do not operate this product on
direct current (DC). A substantial voltage drop will cause a
loss of power and the motor will overheat. If the product does
not operate when plugged into an outlet, double-check the
power supply.
Extension cords
When using a power tool at a considerable distance from a
power source, be sure to use an extension cord that has the
capacity to handle the current the product will draw. An
undersized cord will cause a drop in line voltage, resulting in
overheating and loss of power. Use the chart to determine the
minimum wire size required in an extension cord. Only round
jacketed cords listed by Underwriter's Laboratories (UL)
should be used.
When working outdoors with a product, use an extension cord
that is designed for outside use. This type of cord is
designated with "W-A" or "W" on the cord's jacket.
Before using any extension cord, inspect it for loose or
exposed wires and cut or worn insulation.
A proper extension cord is available at an authorized service
center.
It is possible to tie the extension cord and power cord in a
knot to prevent them from becoming disconnected during use.
Make the knot as shown in the figure, then connect the plug
end of the power cord into the receptacle end of the extension
cord. This method can also be used to tie two extension cords
together.
Minimum Gauge for Extension Cords (AWG)
(when using 120 V only)
6
WARNING