Table of Contents
Advertisement
en Home Connect
Connecting directly
Requirements
¡ Your appliance is now switched off.
¡ Before connecting the appliances, reset all connec-
tions to your home network or other appliances. If
your appliance is connected directly to the hob, it
cannot be connected to your home network as well
and you will not be able to use Home Connect.
Note: Refer to the section entitled "Hob-based hood
1.
control" in the instruction manual for your hob.
Switch on the hob and select the search mode.
Press and hold the button until the LED for
2.
Home Connect flashes in the LED display.
a The appliance is connected to the hob if the LED for
Home Connect no longer flashes and lights up per-
manently.
Connecting via your home network
Follow the instructions in
1.
→ "Automatically connecting the appliance to the
WLAN home network (Wi-Fi)", Page 8 or
→ "Manually connecting the appliance to the WLAN
home network (Wi-Fi)", Page 8.
As soon as the appliance is connected to the home
2.
network, establish the connection to the hob via the
Home Connect app.
Follow the instructions on your mobile device.
3.
Home Connect
This appliance is network-capable. Connecting your ap-
pliance to a mobile device lets you control its functions
via the Home Connect app, adjust its basic settings
and monitor its operating status.
The Home Connect services are not available in every
country. The availability of the Home Connect function
depends on the availability of Home Connect services
in your country. You can find information about this at:
www.home-connect.com.
To be able to use Home Connect, you must first set up
the connection to the WLAN home network (Wi-Fi
to the Home Connect app.
¡ Automatically connecting appliance to WLAN home
network (Wi-Fi) → Page 8
¡ Connecting appliance to WLAN home network (Wi-
Fi) manually → Page 8
The Home Connect app guides you through the entire
login process. Follow the instructions in the Home Con-
nect app to configure the settings.
If the appliance is not connected to your home net-
work, it functions as an appliance with no network con-
nection and can still be operated via the display.
Tips
¡ Please consult the documents supplied by
Home Connect.
¡ Please also follow the instructions in the Home Con-
nect app.
1
Wi-Fi is a registered trademark of the Wi-Fi Alliance.
8
Notes
¡ Please note the safety precautions in this instruction
manual and make sure that they are also observed
when operating the appliance via the Home Con-
nect app.
→ "Safety", Page 2
¡ Operating the appliance on the appliance itself al-
ways takes priority. During this time it is not possible
to operate the appliance using the Home Connect
app.
¡ In networked standby mode, the appliance requires
a maximum of 2 W.
¡ If you need your device's MAC address to connect
to your home network, you can find this next to the
rating plate → Page 14 inside the appliance. To do
this, Remove the filter → Page 10.
Automatically connecting the
appliance to the WLAN home network
(Wi-Fi)
If your router has a WPS function, you can connect the
appliance to your WLAN home network (Wi-Fi) automat-
ically.
Note: The appliance cannot be switched on during the
connection process. Press
Requirements
¡ Wi-Fi on the router is activated.
¡ The appliance receives signals from the WLAN home
network (Wi-Fi) at its installation location.
¡ The Home Connect app is installed on your mobile
device.
¡ The appliance and the light are switched off.
Press and hold the button until LED 7 flashes in
1.
the LED display.
Press .
2.
a LED 1 and LED 7 flash in the LED display.
Press the WPS button on the router within the next
3.
2 minutes.
a If the connection has been established, the appli-
ance automatically connects to the Home Connect
app. LED 3 and LED 7 flash in the LED display.
If no connection can be established, the appliance
4.
1
) and
automatically switches to the manual connection to
the home network, LED 2 and LED 7 flash in the
LED display. Log the appliance manually into the
home network or press
gin.
On your mobile device, follow the instructions for
5.
automatic network login.
a The login process is complete when LED 7 stops
flashing and remains continuously lit.
Manually connecting the appliance to
the WLAN home network (Wi-Fi)
Note: The appliance cannot be switched on during the
connection process. Press
Requirement: The appliance and the light are switched
off.
to cancel the process.
in order to restart the lo-
to cancel the process.
Advertisement
Table of Contents
