Home Connect - Bosch DRC97AQ50 User Manual And Assembly Instructions

en Home Connect
8.2 Connecting via your home network
Follow the instructions in
1.
→ "Automatically connecting the appliance to the
WLAN home network (Wi-Fi)", Page 10 or
→ "Manually connecting the appliance to the WLAN
home network (Wi-Fi)", Page 10.
9
Home Connect
This appliance is network-capable. Connecting your ap-
pliance to a mobile device lets you control its functions
via the Home Connect app, adjust its basic settings
and monitor its operating status.
The Home Connect services are not available in every
country. The availability of the Home Connect function
depends on the availability of Home Connect services
in your country. You can find information about this at:
www.home-connect.com.
To be able to use Home Connect, you must first set up
the connection to the WLAN home network (Wi-Fi
to the Home Connect app.
¡ "Automatically connecting appliance to WLAN home
network (Wi-Fi)" → Page 10
¡ "Connecting appliance to WLAN home network (Wi-
Fi) manually" → Page 10
The Home Connect app guides you through the entire
login process. Follow the instructions in the Home Con-
nect app to configure the settings.
If the appliance is not connected to your home net-
work, it functions as an appliance with no network con-
nection and can still be operated via the display.
Tips
¡ Please consult the documents supplied by
Home Connect.
¡ Please also follow the instructions in the Home Con-
nect app.
Notes
¡ Please note the safety precautions in this instruction
manual and make sure that they are also observed
when operating the appliance via the Home Con-
nect app.
→ "Safety", Page 2
¡ Operating the appliance on the appliance itself al-
ways takes priority. During this time it is not possible
to operate the appliance using the Home Connect
app.
¡ In networked standby mode, the appliance requires
a maximum of 2 W.
¡ If you need your device's MAC address to connect
to your home network, you can find this next to the
"rating plate" → Page 15 inside the appliance. To
do this, "Remove the filter" → Page 12.
9.1 Automatically connecting the appliance
to the WLAN home network (Wi-Fi)
If your router has a WPS function, you can connect the
appliance to your WLAN home network (Wi-Fi) automat-
ically.
Note: The appliance cannot be switched on during the
connection process. Press
1
Wi-Fi is a registered trademark of the Wi-Fi Alliance.
10
1
) and
to cancel the process.
As soon as the appliance is connected to the home
2.
network, establish the connection to the hob via the
Home Connect app.
Follow the instructions on your mobile device.
3.
Requirements
¡ Wi-Fi on the router is activated.
¡ The appliance receives signals from the WLAN home
network (Wi-Fi) at its installation location.
¡ The Home Connect app is installed on your mobile
device.
¡ The appliance and the light are switched off.
Press and hold the
1.
the LED display.
Press .
2.
a LED 1 and LED 7 flash in the LED display.
Press the WPS button on the router within the next
3.
2 minutes.
a If the connection has been established, the appli-
ance automatically connects to the Home Connect
app. LED 3 and LED 7 flash in the LED display.
If no connection can be established, the appliance
4.
automatically switches to the manual connection to
the home network, LED 2 and LED 7 flash in the
LED display. Log the appliance manually into the
home network or press
gin.
On your mobile device, follow the instructions for
5.
automatic network login.
a The login process is complete when LED 7 stops
flashing and remains continuously lit.
9.2 Manually connecting the appliance to
the WLAN home network (Wi-Fi)
Note: The appliance cannot be switched on during the
connection process. Press
Requirement: The appliance and the light are switched
off.
Press and hold the
1.
the LED display.
Press twice to start logging into your home net-
2.
work manually.
a LED 2 and LED 7 flash in the LED display.
Follow the instructions in the app.
3.
a If the connection has been established, the appli-
ance automatically connects to the Home Connect
app. LED 3 and LED 7 light up in the LED display.
On your mobile device, follow the instructions for
4.
manually logging into your network.
a The login process is complete when LED 7 stops
flashing and remains continuously lit.
button until LED 7 flashes in
in order to restart the lo-
to cancel the process.
button until LED 7 flashes in