Sharp PC-GP10 Series Operation Manual
  1. Manuals
  2. Brands
  3. Sharp Manuals
  4. Laptop
  5. PC-GP10 Series
  6. Operation manual
Sharp PC-GP10 Series Operation Manual

Sharp PC-GP10 Series Operation Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
â
NOTEBOOK COMPUTER
PC - GP10 Series
OPERATION MANUAL

Advertisement

Table of Contents
loading

Related Manuals for Sharp PC-GP10 Series

Summary of Contents for Sharp PC-GP10 Series

  • Page 1 â NOTEBOOK COMPUTER PC - GP10 Series OPERATION MANUAL...
  • Page 2 Notice for Users in the UK and Ireland The mains lead of this product is fitted with a non-rewireable (moulded) plug incorporating a 3A fuse. Should the fuse need to be replaced, a BSI or ASTA approved BS 1362 fuse marked and of the same rating as above;...
  • Page 3 Copyright Recording and playback of any material may require consent, which SHARP is unable to give. Please refer particularly to the provisions of the Copyright Act 1956, the Dramatic and Musical Performers Protection Act 1958, the Performers Protection Acts 1963 and 1972 and to any subsequent statutory enactments and...

  • Page 4: Notice For Users In Europe

    Notice for Users in Europe About the Modem Your Sharp PC-GP series with integral modem has been designed to work with the analogue PSTN’s in the following countries: • United Kingdom • Ireland • Italy • Germany • Switzerland If you wish to connect the equipment to the PSTN in a country not listed above, you should contact your equipment supplier for further details.
  • Page 5 This equipment complies with the requirements of the Directive 1999/5/EC. Dieses Gerät entspricht den Anforderungen der EU-Richtlinie 1999/5/EG. Cet appareil est conforme aux exigences de la directive 1999/5/CE. Este aparato satisface las exigencias de las Directiva 1999/5/CE. Quest'apparecchio è conforme ai requisiti delle direttiva 1999/5/CE. Dit apparaat voldoet aan de eisen van de richtlijn 1999/5/EG.
  • Page 6 CAUTION: TO PREVENT ELECTRICAL SHOCK, DISCONNECT THE AC CORD AND THE BATTERY BEFORE SERVICING. CAUTION: FOR A COMPLETE ELECTRICAL DISCONNECTION, PULL OUT THE MAIN PLUG AND THE BATTERY. VORSICHT: UM DIE STROMZUFUHR VOLLSTÄNDIG ZU UNTERBRECHEN, DEN NETZSTECKER HERAUSZIEHEN UND DIE BATTERIE ÈNTFERNEN. ATTENTION: POUR UN ARRET TOTAL DU SYSTEME, DECONNECTEZ LA PRISE DE COURANT SECTEUR ET LA BATTERIE.

  • Page 7: Safety Precautions

    Safety Precautions General • Follow all cautions and instructions, which may be marked, on the computer. • Except as described elsewhere in this manual, refer all servicing to qualified personnel. Immediately shut off the computer and seek servicing under the following conditions: •...
  • Page 8 • Do not drop the computer nor hit it with other equipment. • Do not scratch the surface of the LCD screen. • Turn off the computer and disconnect the AC power cord before cleaning. Battery Pack Precautions CAUTION DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY REPLACED. REPLACE ONLY WITH THE SAME OR EQUIVALENT TYPE RECOMMANDED BY THE MANUFACTURER.
  • Page 9 Discharging • Do not use the battery pack for any purpose other than powering the computer. Storage • Store the battery pack in a cool and dry place. Never allow the temperature to exceed 60 ° C (140 ° F) during storage. •...

  • Page 10: About This Manual

    Information in this manual is subject to change without notice and does not represent a commitment on the part of SHARP Corporation. SHARP Corporation shall not be liable for technical or editorial errors or omissions contained herein; nor for incidental or consequential damages resulting from the furnishing, performance, or use of this material.

  • Page 11: Recording Important Information

    Recording Important Information For future reference, please record the following information in the spaces provided below. Model Number: Serial Number: Date of purchase: Dealer’s Name: Place of purchase: Password: The serial number is printed on a sticker located on the bottom of the computer.

  • Page 12: Manual Conventions

    Manual Conventions This manual uses a set of style conventions described below. Notes and Cautions are italicized with icons: A note icon informs you of a special technique or information that may help you perform a task or better understand a process. A caution icon alerts you to something that may cause problems or damage to hardware, software or data.

  • Page 13: Table Of Contents

    Table of Contents Notice for Users in UK and Ireland ................i Notice for Users in Europe...................iii Safety Precautions....................vi About This Manual ....................ix Recording Important Information................x Manual Conventions....................xi Table of Contents....................xii Overview of Computer ..................xiv Quick Setup Installing Battery Pack..................1-1 Connecting AC Power ..................1-3 Setting Up Windows XP ..................1-5 Turning Off Your Computer ................1-6...
  • Page 14 USB Device....................... 4-8 PC Card ......................4-8 Printer ......................4-11 Using IEEE 1394 Devices................4-12 Communication Functions Built-in Modem ....................5-1 LAN unit......................5-4 Setup Utility Running the Setup Utility .................. 6-1 Main Menu......................6-3 Advanced Menu ....................6-4 Security Menu ....................6-5 Exit Menu ......................

  • Page 15: Overview Of Computer

    Overview of Computer Each number after an arrow indicates the page referring to the part. Actual appearance of your computer may be slightly different depending on the model. Front Microphone LCD Screen → 2-18 Power/ Battery Power/ Battery Status Indicator →...
  • Page 16 Right Optical Drive → 2-9 Left PC Card Slot Floppy Disk Drive Ventilation Openings → 2-7 → 4-8 →vi...
  • Page 17 Rear Microphone Jack IEEE1394 Connector Parallel Port→4-11 → 4-6 →4-12 S Video Output Security Slot →A-7 Jack LAN Jack Audio Output →2-14 →5-4 Jack (S/PDIF compliant) AC Adapter Jack →4-4 →1-3 External Monitor Connector Modem Jack USB Connectors →4-3 →5-2 →4-8 Bottom Memory Slot Cover→A-1...

  • Page 18: Quick Setup

    CHAPTER 1 Quick Setup Your computer is designed and pre-configured for easy setup and use. This chapter describes the steps to get your computer up and running as quickly as possible. Read this chapter first. Installing Battery Pack Your computer is powered with either the rechargeable battery pack or AC power. See the next chapter for more information on power sources.
  • Page 19 Insert the battery pack into the computer. Push the battery pack until you hear the clicking sound. Slide the battery lock lever to the locked position ( ). Turn over your computer and go to the next section.

  • Page 20: Connecting Ac Power

    Connecting AC Power Plug the AC adapter cable to the AC adapter jack on the rear side of your computer. Plug the AC power cord into the AC adapter. Plug the AC power cord into a wall outlet. AC Adapter AC Adapter Jack AC Power Cord To Wall Outlet...
  • Page 21 Slide the display cover lock lever to right until the display cover releases, and raise the cover. Display Cover Lock Button Press the power button to turn on your computer. Power Indicator When you turn on the computer, the power indicator ( ) turns green, the computer goes through a self test to detect any problems, and Windows XP...

  • Page 22: Setting Up Windows Xp

    Setting Up Windows XP The steps in the setup process are as follows: • Configuring your location, language and keyboard • Accepting license agreement • Naming your computer • Creating an account • Completing configuration To set up Windows XP, follow the instructions on the screen. See also the Windows XP quick start guide.

  • Page 23: Turning Off Your Computer

    select Category View, you can choose the category which may be related to what you want to do, then, choose your task by clicking it. If Classic View selected, all the icons appear simultaneously. You can open a property dialog box, or similar window, for the component or feature represented by that icon, by double-clicking it.

  • Page 24: Basic Operations

    CHAPTER 2 Basic Operations This chapter describes the basic operations of your computer. Choosing Power Source You can use the computer with one of the following power sources: • AC power from a wall outlet Use AC power whenever possible; rely on the battery only when AC power is not available.
  • Page 25 About the Power Indicators The following indicators show the power status of your computer. Indicator Light Meaning Power On (green) Operating (powered by AC power) Blinking (green) In System Standby (when powered by AC power) Powered off / in System Hibernate/ powered by a battery pack Battery On (green)

  • Page 26: Resetting The System

    Resetting the System You may need to restart the system if the computer becomes unoperable or after adding new hardware or software. Resetting may cause data loss. Use the resetting process only if the normal Windows XP Shut Down does not work because of software malfunction.

  • Page 27: Using The Glide Pad

    Using the Glide Pad Your computer is equipped with an integrated pointing device called a glide pad. Using the glide pad, you can move the pointer, select an item from a menu, and perform other tasks in the same way you would with a mouse. Glide Pad •...
  • Page 28 have to exert much pressure on the pad. The glide pad will respond to a light touch from your fingertip. Click, Double-click, and Right-click To click or double-click, you can use the left button just like that of a mouse. Instead of clicking the left button, you can also just tap gently anywhere on the rectangular pad.

  • Page 29: Using The Keyboard

    Using the Keyboard Your computer, equipped with the Windows Enhanced Keyboard, provides all the functionality of a full-sized desktop keyboard. Special Keys Opens the Windows Start menu. Windows Key Opens an application-specific short-cut menu equivalent to right-clicking. Application Key System Function Keys When pressed together with the Fn key, function keys set specific system parameters.

  • Page 30: Using The Floppy Disk

    Using the Floppy Disk You can use a double-density (2DD) 720KB or high-density (2HD) 1.44MB floppy disk. Handling Floppy Disks • Do not open the shutter and touch the disk inside; otherwise, you will not be able to read or write data to the disk. •...
  • Page 31 difficulty inserting or removing disks, seek the assistance of an authorized service technician. • Do not touch the disk while reading/writing data. It may cause malfunction of the computer and the drive. Removing Before removing the floppy disk, make sure the floppy disk indicator is not lit.

  • Page 32: Using An Optical Drive

    Using an Optical Drive With the optical drive, you can read data from CD and write data into CD-R/RW. Furthermore, you can enjoy a movie etc, with the DVD-ROM disk. CAUTION FOR LASER Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.
  • Page 33 Inserting a Disk Make sure the optical drive indicator does not light on; then, press the eject button to open the drive tray slightly. Optical drive Indicator Gentry pull out the tray. Place your disk, label side up, onto the tray and slightly press the center of the disk until it clicks into the place.
  • Page 34 Gently push the tray back into the computer. • Do not leave the tray pulled out. Also, avoid touching the lens in the tray. If the lens becomes dirty, the disk may malfunction. • Do not wipe the lens with materials with rough surface (such as paper towels).

  • Page 35: Writing Data To Cd-R/Rw

    Writing Data to CD-R/RW You can use a CD-R or a CD-RW disk to write data on. CD-RW is an erasable disk to which you can write data onto and from which you can erase data. CD-R is non-erasable disk to which you can write data only once. If free space remains, you can add data until the disk is full.

  • Page 36: Watching Dvd-Rom Video

    Watching DVD-ROM Video You can enjoy watching DVD-ROM video on your computer using the application called Win DVD. See online help of Win DVD for more details. Before watching DVD-ROM video, follow the instructions below: • Connect the AC adapter. If the battery is discharged, the operation will stop.
  • Page 37 Your DVD drive Region can be changed four times. Once this limit is reached, it cannot be changed again. To change the region code: Insert a DVD-ROM disk into the drive. If the region code of your disk is different from that of your DVD-ROM drive, the message “Playback of content from this region is not permitted”...
  • Page 38 Connect the television set to your computer. S Video Output Jack To S Video Input Jack Audio Output Jack Stereo Mini Plug To Audio Input Jacks: White Plug to Left Red Plug to Right Turn on the computer and the television set. Right-click somewhere on the Windows desktop.
  • Page 39 Enjoying Dolby Digital Audio Your computer is Dolby Digital compliant. If you connect Dolby Digital compliant audio equipment or headphones, you will have an audio output similar to a big theater. For connection, refer to Audio System of Chapter 4. WinDVD is equipped with Dolby Headphone properties You can enjoy...

  • Page 40: Controlling Audio

    Controlling Audio You can control the output volume of your computer by the following steps. With the keyboard Press Fn and F3 keys simultaneously to decrease the output volume. Press Fn and F4 keys simultaneously to increase it. This operation also adjusts the Windows volume control below. For example, if you press Fn + F3 keys, the volume level in Windows will decrease, too.

  • Page 41: Adjusting The Display

    Adjusting the Display You can adjust the brightness, resolution, and number of colors of the internal LCD display. Changing Brightness of Display Press Fn and F6 keys simultaneously to decrease the brightness of the display. Press Fn and F7 keys simultaneously to increase it. Press Fn and F8 keys simultaneously to maximize it.
  • Page 42 1024 x 768 dots. To see the hidden parts, move mouse pointer to the parts and scroll it. • You cannot switch to a display resolution and number of colors that are not available. • In the Color quality, Medium (16 bit) means 65,536 (64K) colors, and Highest(32 bit) means about 16,770,000 (16M) colors.

  • Page 43: Sharing The Computer

    Sharing the Computer If you are sharing the computer with your colleagues or family members, set a user account for each person. Every user can choose their favorite desktop setting, web site lists, or make their own My Documents folder etc., and save them to their user account.
  • Page 44 Click start - Log Off. Select Switch User or Log Off. If you select Log Off, the dialog box, which asks you to save your data may appear. Select a new account to start Windows XP again. • If you cannot see Switch User in Log Off Windows dialog box, click Change the way users log on or off in User Accounts dialog box, and check Use Fast User Switching and click Apply Options.
  • Page 45 Changing Password Follow the steps 1-2 on the above section. Select the account you want to change, if you log on to the computer with an Administrator account. If you log on the computer with a limited account, go to the next step. (You cannot change the password for another user account.) Select Change the password.

  • Page 46: Battery And Power Management

    CHAPTER 3 Battery and Power Management This chapter explains how to manage the computer’s power effectively and use the battery pack. In this section, you often see the expression “Power Options Properties dialog box”. To open the dialog box: Click start - Control Panel. Click Performance and Maintenance - Power Options in Category view or double-click Power Options icon in Classic view.
  • Page 47 Management section in this chapter. • When the battery has not been charged, your computer may not operate properly. Connect the AC power to charge the battery. Charging the Battery Pack Connect the AC adapter to the computer. While the battery is being charged, the battery status indicator turns orange.
  • Page 48 Low Battery Indication When the battery power becomes significantly low (under 10%), the battery status indicator ( ) blinks red, the warning beep sounds. Save your data and turn off the computer, or connect the computer to AC power immediately. Otherwise, the computer will be shut down and the data may be lost.
  • Page 49 Turn on the computer. When the message <F2> to enter System Configuration Utility appears, press F2 to open the Setup Utility. Disconnect the AC adapter, and leave the computer on until the battery is completely discharged and the system shuts down automatically. Connect the computer to AC power and let the battery fully charge again.
  • Page 50 Slide the battery release lever to right and hold it; then, pull out the battery pack. Battery Release Lever Lift up the battery pack and remove it from the computer. Insert a new battery pack into the computer. Push the battery pack until you hear the clicking sound.
  • Page 51 Slide the battery lock lever to the locked position ( ). Turn over the computer and it’s ready to use.

  • Page 52: Power Management

    Power Management Power management saves electricity and extends battery life by controlling power supply to built-in devices. You can set the following power management properties in Windows XP. • Stopping power supply to the hard disk • Stopping power supply to the display •...
  • Page 53 Using System Standby/Hibernate System standby/hibernate is a very useful power management tool. For example, after your computer has entered System standby mode, you can restart your computer more quickly when compared to a restart, after a normal shutdown operation. When your computer resumes from System standby/hibernate, the system restores the exact last state of the computer.
  • Page 54 battery for long periods of time, we recommend System hibernate. Confirm that System hibernate is supported by the following steps below. In the Power Options Properties dialog box, select Hibernate tab. Confirm Enable hibernation is checked. Click OK. Close Control Panel window. Set Timer to Enter System standby/Hibernate Automatically Your computer will enter System standby/hibernate automatically when the specified time has passed without any operation.
  • Page 55 • You press the power button. The above functions if you perform the following: In the Power Options Properties dialog box, select Advanced tab. Select Hibernate or Stand by in When I press the power button on my computer: Click OK. Close Control Panel window.

  • Page 56: Peripherals

    CHAPTER 4 Peripherals This chapter describes how to use peripheral devices with your computer. You can connect a printer, external monitor, or other devices to your computer. To ensure proper use, be sure to read the instructions for each peripheral device before connecting it to your computer.
  • Page 57 Peripheral Connection Overview Audio Equipment (S/PDIF compliant) External Monitor Microphone IEEE 1394 Device Printer Video Equipment with USB Devices S Video connector...

  • Page 58: Display

    Display You can use an external monitor with your computer. To display images on both displays simultaneously, use the 1024x768 resolution. • Some monitors, which are not compatible with your computer, may not display correctly. • In this section, you often see the expression “Display Properties dialog box.”...

  • Page 59: Audio System

    Displaying the Screen on an External Monitor To display the screen on an external monitor, you may need to install the driver for your external monitor. Before using the external monitor, refer to the manual included with your external monitor. Switching the Display 1.
  • Page 60 Connecting Digital Audio Equipment The audio output jack of the computer is compliant to S/PDIF (Sony/Philips Digital Interface). You can connect S/PDIF compliant audio equipment to the computer and output/record sound. Audio Output Jack S/PDIF Compliant Audio Equipment S/PDIF Compliant Audio Cable When recording sound with an audio equipment: •...
  • Page 61 Connecting Analog Audio Equipment Audio Output Jack White You can adjust the output volume in Windows XP by double-clicking the speaker icon in the taskbar or use Fn + F3 or F4 keys combination. Connecting Headphone Use headphones with an impedance of more than 8Ω (32Ω is recommended). Audio Output Jack Connecting a Microphone You can input sound using an external microphone connected to the microphone...
  • Page 62 Microphone Jack To record sound: Click start; then, point All Programs –Accessories – Entertainment. Click Sound Recorder. See Help for Sound Recorder for more details.

  • Page 63: Usb Device

    USB Device With a USB connection, you can connect/disconnect peripherals without turning off the computer. Generally, when you connect a device to the computer, the necessary driver will be installed automatically. See also the manuals of peripheral devices supporting USB. To remove USB devices, you may need to perform the following before you remove them: Click Unplug or Eject Hardware icon (...
  • Page 64 Inserting a PC Card When a new card is correctly inserted, the appropriate driver is automatically installed. If the driver is not installed correctly, you will hear a warning beep. In this case, install the PC card driver by following the instructions on the screen. Confirm the PC card eject button is inside the computer cabinet.
  • Page 65 Ejecting PC Card • Some PC cards may become hot after long use. • Be sure to use the procedure below when ejecting a PC card. Otherwise, the system may not work properly. Click the Unplug or Eject Hardware icon ( ) on the taskbar.

  • Page 66: Printer

    Printer You can connect a printer to the parallel port or the USB port. Before using a printer, read the printer manual and install the printer driver. Connecting to Parallel Port Turn off the computer and the printer. Connect the computer and the printer with the printer cable. If the connector has screws, tighten them.

  • Page 67: Using Ieee1394 Devices

    Using IEEE1394 Devices You can connect the IEEE 1394 devices to the IEEE1394 port on the rear side of the computer. The IEEE 1394 is a digital interface for handling digital video, digital audio and other data in two directions between devices, and for controlling other equipment.
  • Page 68 Connect the other end of the DV cable into the DV connector of the IEEE 1394 device. IEEE 1394 connector To IEEE 1394 Compliant Device Install the driver according to the instructions on the screen. Generally when you connect the device to the computer, the necessary driver will be installed automatically.
  • Page 69 4-14...

  • Page 70: Communication Functions

    CHAPTER 5 Communication Functions This chapter explains how to use the built-in modem and the LAN unit. Built-in Modem You can use the built-in modem for data transfer and fax communication. • The built-in modem on your computer is designed only for regular analog telephone lines.
  • Page 71 modem cable to the telephone line. To Telephone Modem Modem Cable Core Jack Be sure not to connect to the LAN jack (with mark) next to the modem jack. It may damage both the modem cable and the LAN jack. Turn on the computer.
  • Page 72 Internet Connection Windows XP has a special Internet Connection Wizard to help you to connect to the Internet with ease. Click start – Control Panel. Click Network and Internet Connections; then, Network Connections. If Classic view is selected, double-click Network Connections icon. . In Network Connections dialog box, click Create a new connection of Network Tasks.

  • Page 73: Lan Unit

    LAN unit You can connect to a LAN (Local Area Network) with the 100 Base-TX/10 Base-T LAN unit on your computer. To activate the LAN unit, perform the following steps. Use a category 3 LAN cable when connecting to 10 BASE-T LAN, and the category 5 when connecting to 100 BASE-TX LAN.
  • Page 74 LAN Jack To Network Hub Do not connect the LAN cable to the modem jack (with mark) next to the LAN jack. It will damage the LAN cable and the modem jack. Turn on the computer. Click start - Control Panel. Click Network and Internet Connections;...

  • Page 76: Setup Utility

    CHAPTER 6 Setup Utility This chapter describes how to run the Setup Utility to change settings on your computer. Running the Setup Utility With the Setup Utility, you can customize the system configuration information, such as time and date, port assignments, or passwords. The information you have specified is saved in a special area called CMOS RAM, which the system reads every time you turn on the computer.
  • Page 77 Entering and Exiting the Setup Utility Turn on the computer. When <F2> to enter System Configuration Utility appears, press F2 . The Setup Utility opens. Change the desired settings. Refer to the next section. Select Exit menu; then press Enter . Select one of the exit methods, and press Enter .

  • Page 78: Main Menu

    Main Menu Date and Time defines the system date and time. Use arrow keys to select the value, and minus key or space bar to change value. Hard Disk Type shows the type of the hard disk of your computer. Press Enter to show the details.

  • Page 79: Advanced Menu

    Advanced Menu LPT Port sets the printer port, selecting the base I/O address and IRQ. Disabled means that you cannot use the port. Mode can be selected from Bi-Directional, ECP (Extended Capabilities Port mode), EPP (Enhanced Parallel Port mode) or Output Only.

  • Page 80: Security Menu

    Security Menu Set Password defines the password (up to eight characters). See the next section about the password setting. If you lose your password, you will be unable to access the computer or change the configuration. Make sure to select a password you will never forget, or write it down and protect it in a secure place.
  • Page 81 Changing the Password In the Security menu of the Setup Utility, select Set Password and press Enter . Type your current password, and press Enter . Type your new password, and press Enter . Type your new password again, and press Enter . If you want the password is required when booting, confirm Password on Boot is marked with ×.

  • Page 82: Exit Menu

    Exit Menu Exit Saving Changes saves the settings you have changed and exits the Setup Utility. Exit Discarding Changes exits the Setup Utility without saving the settings you have changed. Load Setup Defaults returns the values of all items to the default. To exit, select one of the above items.

  • Page 84: Appendixes

    Appendixes The appendixes contain additional information on the use and care of your computer. Memory Module (PC-GP10-CM only) You can expand the memory size by installing a memory module. For available memory modules, ask your local dealer. Default memory size is 256MB (PC-GP10-CM) and 512MB (PC-GP10-CH). PC- GP10-CH is not memory expandable.
  • Page 85 Loosen two screws and remove the memory slot cover. Memory Slot Cover Align the memory module as shown below, matching the notched part of the module with the projected part of the memory socket of the computer. Left Slot Right Slot Projected Part 20°...
  • Page 86 Press the memory module slowly to place it into the memory socket until you hear the clicking sound. Replace the memory slot cover to the computer matching the projected parts of the cover with the notched parts of the computer. Tighten the screws.

  • Page 87: Maintenance And Care

    appear at the bottom of the sentence. Share video memory size will not be included with the value. Uninstalling the Memory Module Follow steps 1-2 of Installing the Memory Module. Slightly bend the two latches outward until the memory module is released. Remove the memory module and follow steps 5-8 of Installing the Memory Module.
  • Page 88 Loosen the screw and remove the cover of the backup battery box. Remove the backup battery. • Never use a metallic material. If the material touches to the circuit, your computer may malfunction. Insert a new backup battery with the plus side (a part number is printed) up. Insert a battery into two hooks of the box and press down the battery.
  • Page 89 Replace the backup battery box cover to the computer matching the projected parts of the cover with the notched parts of the computer. Tighten the screw. Insert the battery pack and turn over the computer. Connect the AC adapter and turn on the computer. If you see the message Press F1 to Continue, Del to Load CMOS defaults, press Delete key.
  • Page 90 Using a Security Cable You can connect a security cable to the security slot on the rear side of your computer to prevent theft. Cleaning the Computer Cabinet Apply a small amount of mild cleaning solution to a dry, lint-free cloth and wipe the cabinet with the cloth.
  • Page 91 Screen The surface of the screen may become smeared and accumulate dust during use. Avoid touching the screen with your fingers when using the system. Gently wipe the surface of the screen with a soft cloth that has been dipped in a mild detergent solution and squeezed dry.

  • Page 92: Re-Installation Instructions

    Re-installation Instructions To recover your hard disk, you will use PowerQuest®EasyRestore™. Before starting re- installation, read the following End User License Agreement first. PowerQuest(R) EasyRestore (TM) End User License Agreement IMPORTANT: Read this before using your copy of PowerQuest software. This document is a legal agreement between you, the "end user,"...
  • Page 93 disclosure by the Government is subject to restrictions as set forth in subparagraph (c)(1)(ii) of the Rights in Technical Data and Computer Software clause at DFARS 252.227-7013or subparagraphs (c)(1) and (2) of the Commercial Computer Software-Restricted Rights at 48 CFR 52.227-19, as applicable. Contractor/manufacturer is PowerQuest Corporation/P.O.
  • Page 94 Preparation for Re-installation You can format the hard disk and re-install the preinstalled software with the recovery CD-ROM, and set the status of your computer to the same configuration as shipped from the factory. Necessary for re-installation are the following: •...
  • Page 95 restored to its original state in C: drive. Formatting the drives and re-installing Windows XP 1. Make sure the computer is turned off. 2. If any peripheral devices are connected to your computer, disconnect them. 3. Connect the AC adapter; then, turn on the computer. •...
  • Page 96 12. If you see the message The hard disk has been recovered successfully, the Optical drive will be opened automatically. Remove the Product Recovery CD-ROM disk 2. The system will restart automatically. 13. Set up Windows XP, following the instructions on the screen. Make sure to set date and time.

  • Page 97: Specifications

    Specifications Parts PC-GP10-CH PC-GP10-CM 1.2GHz Mobile AMD Athlon4 1.1GHz Mobile AMD Athlon4 Processor Processor Primary cache 128KB (Integrated with CPU) Secondary cache 256KB (Integrated with CPU) Including system BIOS,VGA BIOS, Plug&play compliant BIOS System SDRAM 512MB (not SDRAM 256MB (expandable) expandable) Video 16MB (default setting.

  • Page 98: Troubleshooting

    Troubleshooting This chapter describes how to troubleshoot computer problems. Common Problems Problems with your computer can be caused by something as minor as an unplugged power cord or as major as a damaged hard disk drive. The information in this troubleshooting section is designed to help you find and solve minor problems.
  • Page 99 Trouble when Starting Question: Why doesn't the power indicator or the battery power indicator turn on? • Make sure the AC adapter is correctly connected to the AC adapter jack of your computer. • Make sure the AC power cable is correctly connected to a live wall outlet. Connect another electric equipment to the wall outlet and check whether it is live or not.
  • Page 100 Question: Why do I get the message Press ‘H’ to retry Hard Disk, any other key for floppy? • If you cancel the re-installation on the way, you will see the message. Refer to Re-installation Instructions of Appendixes and re-install the system. Make sure to select Recovers both C: and D: drive when re-installing the system.
  • Page 101 Question: Why can’t I change the display with Fn + F5 keys? • When playing the animation or game, Fn + F5 key combination may not work. Close the currently running application. • Use Display Properties dialog box to change it. •...
  • Page 102 Trouble with Floppy Disks Question: Why can't I use a floppy disk? • Confirm the floppy disk is inserted correctly. • Confirm the drive and file name are correct. • The floppy disk may not be formatted or could be corrupted. Format the disk or use another disk.
  • Page 103 • Confirm the drive and file names are correct. • Confirm the disk is not stained or scratched. • Confirm the disk or files are supported. Question: Why doesn’t the DVD movie play smoothly? • Set back the screen resolution, color quality and screen refresh rate to the default value.
  • Page 104 you connect the modem to a digital PBX, both the modem and the PBX may be damaged. Question: Why is the access speed so slow? • Close the applications currently opened. • Try to connect another ISP (Internet Service Provider), or try to connect in some other time.
  • Page 105 Question: Why don't peripheral devices function correctly? • Set System standby and System hibernates to Never in Power Options Properties dialog box. If this does not work, set Turn off hard disks to Never . • Confirm they are Windows XP compliant. •...
  • Page 106 Question: Why can't I turn off the computer? • Follow the instructions on Why doesn't the keyboard or the glide pad function ? Question: Why the computer is so hot? • When charging the battery pack, its surrounding area or the front of the keyboard may become hot, but this is not a problem.
  • Page 107 T-10...
  • Page 108 Index removing, 2-11 CD-R/RW, 2-12 AC adapter connecting, 1-3 using, 2-2 Display Account changing brightness, 2-18 creating, 2-20 changing resolution, 2-18 deleting password, 2-22 changing number of colors, 2-18 setting password, 2-21 switching the display, 2-6, 4-4 switching, 2-20 troubleshooting, T-3 Audio turning off, 2-6 controlling output volume, 2-17...
  • Page 109 connecting to telephone line, 5-1 troubleshooting, T-6 Glide pad changing configuration, 2-5 clicking and double-clicking, 2-5 drag and drop, 2-5 Optical drive scroll, 2-5 troubleshooting, T-5 troubleshooting, T-4 Hard disk drive Passwords troubleshooting, T-5 changing, 6-6 deleting, 6-6 setting, 6-5 PC cards IEEE 1394 device, 4-12 inserting, 4-9...
  • Page 110 Resetting power button, 2-3 Television set, 2-14 reset switch, 2-3 Troubleshooting common problems, T-1 communications, T-6 display, T-3 Setup utility floppy disk drive, T-5 advanced menu, 6-4 hard disk drive, T-5 entering and exiting, 6-2 keyboard or glide pad, T-4 exit menu, 6-7 peripherals, T-7 main menu, 6-3...
  • Page 111 SHARP CORPORATION ã 2001 SHARP CORPORATION PRINTED IN CHINA TINSE3354ACZZ 1...

This manual is also suitable for:

Pc-gp10-chPc-gp10-cm

Table of Contents