Hatco THERMO-FINISHER TF-2005 Installation & Operating Manual
Tf 2000 series food finisher
Hide thumbs
Also See for THERMO-FINISHER TF-2005:
- Specification sheet (2 pages) ,
- Brochure & specs (3 pages)
Table of Contents
Advertisement
Quick Links
THERMO-FINISHER
This manual contains important safety information
concerning the maintenance, use and operation
of this product. Failure to follow the instructions
contained in this manual may result in serious injury.
If you're unable to understand the contents of this
manual, please bring it to the attention of your
supervisor. Do not operate this equipment unless
you have read and understood the contents
of this manual.
Food Finisher
TF 2000 Series
Installation &
Operating Manual
I & W #07.05.110.00
Este manual contiene importante información sobre
seguridad concerniente al mantenimiento, uso y
operación de este producto. Cualquier falla en el
seguimiento de las instrucciones contenidas en este
manual puede resultar en un serio daño. Si usted no
puede entender el contenido de este manual por
favor pregunte a su supervisor. No opere este equipo
al menos que haya leído y comprendido el contenido
de este manual.
™
Advertisement
Table of Contents
Related Manuals for Hatco THERMO-FINISHER TF-2005
Summary of Contents for Hatco THERMO-FINISHER TF-2005
- Page 1 THERMO-FINISHER Operating Manual This manual contains important safety information concerning the maintenance, use and operation of this product. Failure to follow the instructions contained in this manual may result in serious injury. If you’re unable to understand the contents of this manual, please bring it to the attention of your supervisor.
-
Page 2: Table Of Contents
Thermo-Finisher Food Finisher. We recommend all installation, operating and safety instructions appearing in this manual be read prior to installation or operation of your Hatco Food Form No. TF20M-0603 Programming The Unit ...7 General ...7 Programming Controller ...8... -
Page 3: Important Safety Instructions
To avoid electrical shock or personal injury, do not steam clean or use excessive water on the unit. If service is required on this unit, contact your Authorized Hatco Service Agent, or contact the Hatco Service Department at 800-558-0607 or 414-671-6350; fax 800-690-2966 or International fax 414-671-3976. - Page 4 Some aftermarket or generic replacement parts do not have the characteristics that will allow them to operate safely in Hatco equipment. It is essential to use Hatco Replacement Parts when repairing Hatco equipment. Failure to use Hatco Replacement...
-
Page 5: Model Descriptions
A plate rack and attached cord and plug set are included. MODEL TF-2005 The TF-2005 model features two upper elements and a removable broiler pan for heating food product. Loading and unloading of food is done on the control side of the unit. -
Page 6: Specifications
If the plug and receptacle do not match, contact a qualified electrician to determine the proper voltage and size and install the proper electrical outlet. Model Voltage TF-2005 TF-2010 TF-2015 TF-2020 TF-2030 TF-2040 TF-2045 * NEMA L15-30P for Canada. -
Page 7: Dimensions
DIMENSIONS EXTERIOR DIMENSIONS Model (A) Width (B) Depth 19-1/2"†♦ ♦ TF-2005 14" (356 mm) (495 mm) TF-2010 15-1/4" 21-3/4" (387 mm) (553 mm) TF-2015 15-1/4" 21-3/4" (387 mm) (553 mm) TF-2020 19-3/8" 21-1/8" (492 mm) (537 mm) TF-2030 19-3/8" 22-7/8"... -
Page 8: Installation
INSTALLATION UNPACKING 1. Remove unit from box. 2. To prevent delay in obtaining warranty coverage, fill out and mail in warranty card. 3. Remove tape and protective packaging from all surfaces of unit. 4. Place wire plate rack on top of rack supports, making sure plate rack is not in direct contact with glass base. -
Page 9: Programming The Unit
GENERAL Thermo-Finisher units (except TF-2005, TF-2010 ™ and TF-2045) have both an upper and lower heating zone. The upper elements heat the product on the plate and the lower elements heat the center of the plate. Five adjustable program button selections allow the operator to fine tune the radiant heat input and heating time for a variety of menu items. -
Page 10: Programming Controller
NOTE: Models TF-2005, TF-2010 and TF-2045 do not have lower heating elements but all steps must be performed as if a bottom heating element is present. The power (LP) and time (LT) values set for the bottom zone must be less than the top zone for proper operation. - Page 11 PROGRAMMING CONTROLLER Figure 7. Programming a Selection Form No. TF20M-0603...
-
Page 12: Idle Mode
PROGRAMMING CONTROLLER IDLE MODE The Thermo-Finisher features an “Idle” mode. Once ™ the unit reaches the rEdY mode, the upper heating element(s) automatically go into a programmed idle power setting. (The display will still show rEdY during the idle mode). The unit will stay in this mode until one of the five Program buttons is pressed, or the unit goes into auto-shut off. - Page 13 Figure 8. Programming Idle Mode Figure 9. Programming Auto-Off Mode PROGRAMMING CONTROLLER Form No. TF20M-0603...
-
Page 14: Operation
OPERATION BASIC FOOD FINISHING CAUTION Some exterior surfaces on the unit will get hot. Use caution when touching these areas to avoid injury. CAUTION To avoid any injury or damage to the unit do not operate appliance without installation of supplied legs. CAUTION DO NOT use “Pyrex”... -
Page 15: Maintenance
Some aftermarket or generic replacement parts do not have the characteristics that will allow them to operate safely in Hatco equipment. It is essential to use Hatco Replacement Parts when repairing Hatco equipment. Failure... -
Page 16: Recommended Food Finishing Guide
RECOMMENDED FOOD FINISHING GUIDE Food Item Upper Power Value Upper Time Value Bratwurst On tray, precooked for 20 minutes. Broccoli Mornay Topped with a white sauce. Broiled Seasoned Tomato Halves Cauliflower Mornay Topped with a yellow cheese sauce. Chicken Fillet Banquette honey- mustard breast patties. - Page 17 Food Item Upper Power Value Upper Time Value Philly Sandwich Toast Hoagie Roll separate from meat, onion and pepper filling. Sugar Cookies Made on pizza pan. Pizza-Thin Crust Pork Kebabs Seasoned pork tenderloin squares on metal skewers, soy seasoned Potatoes Au Gratin Boiled, diced, potatoes in a cheddar cheese sauce.
-
Page 18: Hatco Limited Warranty
Hatco reserves the right to accept or reject any such claim in whole or in part. Hatco will not accept the return of any Product without prior written approval from Hatco, and all such approved returns shall be made at Buyer’s sole expense. - Page 19 NOTES Form No. TF20M-0603...
-
Page 20: Authorized Parts Distributors
NEW YORK GCS Service Acme American Repairs, Inc. Indianapolis 317-545-9655 Brooklyn Parts & Service Fax (800) 690-2966 Printed in U.S.A. June 2003 HATCO AUTHORIZED PARTS DISTRIBUTORS NEW YORK (continued) Alpro Service Co. 319-323-1823 Brooklyn Appliance Installation Buffalo Northern Parts Dist.