Gas Supply Requirements - Whirlpool WFR7300S Instruction For Installation, Use And Handling

Gas Supply Requirements

This range is ready to work with L.P. gas from a mobile or stationary tank.
To use your range with natural gas (pipe) you must call Whirlpool Service to change the nozzle and make
the necessary adjustments. See the "Service" section on p. 22
The qualified technician must carry out the conversion of both the upper burner jets and the range regulator
(in case the model has this); you must make sure that the connection is not leaking and that the gas
pressure in the stove is as shown below:
2.75kPa< 2750 Pa< 27.5 mbar
CONNECTION OF THE RANGE TO THE GAS LINE FOR MODELS:
A combination of splice pipes must be used to connect the range to the existing gas supply line. Your
connection may be different, according to the type of supply line, size and location.
1. To connect your range, use the material specified in the figure below:
CONNECTION OF THE RANGE TO THE GAS LINE FOR MODELS:
For models
WFR73000S,
WFR7400S,
WFR9000S,
WER9000S,
WFR9100S and
WER9100S
2.
Once your gas line is connected, OPEN the gas supply valve and check that there are no leaks by pouring
soap bubbles on the connections and elbows of the pipes.
3.
Check that the copper pipe is not damaged or bent in a way that obstructs the passage of gas to your
range..
DO NOT USE PLASTIC HOSES FOR GAS CONNECTIONS BECAUSE THEY CAN LEAK, EVEN THOSE
Recommendations:
•
If the installation is not new, clean the pipes to avoid plugging the nozzles.
•
In order to facilitate the movement of the appliance, the installer must make a coil with the copper
flexible pipe and install a shutoff valve in the gas supply line. This valve must be outside the range and
accessible to the people who use it.
•
Always use pipes and pressure regulators according to local regulations.
•
Check the validity of the tubes and pressure regulators and replace them if necessary.
•
Tighten all gas connections properly during installation.
In some European factories the letter "W" of the part code mentioned herein will be automatically •
When moving your range, avoid damaging the gas connection to avoid gas leakage.
30-Mar-2020 13:12:28 EDT | RELEASED
Operative pressure LP gas
28 cm water column
MODEL
WFR7300S
WFR7400S
WFR9000S
WER9000S
WFR7600S
WER7600S
WFR9100S
WER9100S
Stove
regulator
NOTE: The material shown for this installation does not come with the stove.
Stove regulator
Cople NPT 1/2 to
3/8"
NOTE:The material shown for installation is not included with the stove
DO NOT USE FLAMES TO DETECT GAS LEAKS.
THAT HAVE STEEL MESH ON THEIR SURFACE.
replaced by the number "4000" (e.g. "W12345678" becomes "400012345678")
Operative pressure Natural gas
1.76 kPa< 1760 Pa< 17.6 mbar
18 cm water column
LP gas kit to natural gas
W11344945
W11344946
W11344947
W11344948
W11353307
W11353308
Copper tube with conical
nuts 9.5mm (3/8 ") in length
Copper tube with
necessary to reach the gas
9.4mm (3/4 ")
conical nuts
3/8 "9.5mm stopcock
Copper tube with conical
nuts 9.5mm (3/8 ") in length
Copper tube with
necessary to reach the gas
9.4mm (3/4 ")
conical nuts
3/8 "9.5mm stopcock
WFR7600S Y WER7600S
Gas
regulator
9.5mm
Cople-nipple
(3/8 NPT)
Gas
regulator
Cople-Niple
9,5mm (3/8"
de
NPT)
32