Fastener Specifications; Operation - Craftsman CMPPN23 Instruction Manual

English

FASTENER SPECIFICATIONS

Model
Nail
Lengths 1/2" (13 mm) –1" (25 mm)
Air Inlet
nOTE: Use only CRAFTSMAN approved fasteners.
Trigger (Fig. A)

WARNING: Keep fingers AWAY from trigger when not
driving fasteners to avoid accidental firing. Never carry
tool with finger on trigger.

WARNING: Once the secondary trigger is pulled the
tool will drive a fastenere every time the primary trigger
is pulled.
This tool is equipped with with a dual trigger actuation
system. the secondary trigger
to depress the primary trigger
trigger is depressed the tool will fire a fastener.
Air Fitting (Fig. B, C)
The tool is equipped with a 1/4" (6.4 mm) male quick
connector coupling. A 3/8" (9.5 mm) male quick connector
coupling may be used when a 1/4" (6.4 mm) supply line is
not available.
nOTE: A 3/8" (9.5 mm) supply line (and fittings) are required
for maximum tool performance. iMPORTAnT: Always use
couplings that relieve all pressure from the tool when it
is disconnected from the power supply. Always use hose
connectors that shut off air supply from compressor when
the tool is disconnected.
To Install an Air Fitting
1. Wrap the male end of the fitting with thread seal tape
prior to assembly to eliminate air leaks.
2. To install a 1/4" (6.4 mm) fitting: screw it directly into the
and tighten firmly. nOTE: If a cap is in the air
air inlet 3
inlet, remove it prior to inserting the fitting.
3. To install a 3/8" (9.5 mm) fitting: screw the fitting into the
3/8" (9.5 mm) adapter and then into the air inlet of the
tool and tighten firmly.
Preparing the Tool

WARNING: Read the section titled IMPORTANT
SAFETY INSTRUCTIONS at the beginning of this
manual. Always wear proper eye [ANSI Z87.1 (CAN/
CSA Z94.3)] and hearing protection [ANSI S12.6 (S3.19)]
when operating this tool. Keep the fastener pointed
away from yourself and others. For safe operation,
complete the following procedures and checks before
each use of the fastener.
NOTICE: To reduce the risk of damage to the tool,
only use pneumatic tool oil or a non‑detergent SAE
20 weight oil. Oil with additives or detergent will
damage tool parts.
6
23 gauge pin nails
1/4" NPT (6.4 mm)
2 must be depressed in order
1 . Each time the primary
• Before you use the tool, be sure that the compressor
tanks have been properly drained. nOTE: Use a filter and
regulator when possible.
• Wear proper eye, hearing and respiratory protection.
• Remove all fasteners from the magazine.
• Check for smooth and proper operation of contact trip
and pusher assemblies. Do not use tool if either assembly
is not functioning properly. NEVER use a tool that has the
contact trip restrained in the up position.
• Check air supply: Ensure air pressure does not exceed
operating limits; 60 to 100 p.s.i.g., (4.1 to 6.9 kg/cm
• Lubricate tool:
Use CRAFTSMAN pneumatic tool oil or a
‑
non-detergent S.A.E. 20 weight oil. DO NOT use
detergent oil or additives as they will damage O-rings
and rubber parts.
‑ Use a filter when possible.
‑ Add 5 to 7 drops of oil in the air fitting a least twice
a day.
• Keep tool pointed away from yourself and others.
• Connect air hose.
• Check for audible leaks around valves and gaskets. Never
use a tool that leaks or has damaged parts.
Using the Secondary Trigger (Fig. A)

WARNING: To reduce the risk of injury, Always wear
proper eye [ANSI Z87.1 (CAN/CSA Z94.3)] and hearing
protection [ANSI S12.6 (S3.19)] when operating
this tool.

WARNING: Do not keep trigger depressed when tool is
not in use. Serious personal injury may result.

WARNING: Disconnect air line from tool and remove
fasteners from magazine before making adjustments.
Serious personal injury may result.
The tool is locked off until the secondary trigger
is depressed.

OPERATION


WARNING: To reduce the risk of serious personal
injury, turn unit off and remove air supply before
making any adjustments or removing/installing
attachments or accessories. An accidental actuation
can cause injury.
Proper Hand Position (Fig. D)

WARNING: To reduce the risk of serious personal injury,
ALWAYS use proper hand position as shown.

WARNING: To reduce the risk of serious personal
injury, ALWAYS hold securely in anticipation of a
sudden reaction.
Proper hand position requires one hand on the main
handle 9 .
2 ).
2