Subscribe to Our Youtube Channel
Related Manuals for Global Fire Equipment JUNO NET
Summary of Contents for Global Fire Equipment JUNO NET
- Page 1 G L O B A L F I R E E Q U I P M E N T JUNO-NET Fire Alarm Control Panel CONNECTION SCHEMATICS June 15, 2004 Revision 0.12...
-
Page 2: Connection Schematic
CONNECTION SCHEMATIC Typical System Schematic G L O B A L F I R E E Q U I P M E N T J-NET-CON CON 1 MAX CURRENT PER LAMP =100mA CON 6 CON 5 MAX 3A FAST ACTING CON 2 EARTH AUX 1... - Page 3 L1 L1 LOOP INPUT October 11, 2003 Revision 0.10...
- Page 4 CONNECTION SCHEMATIC G L O B A L F I R E E Q U I P M E N T L1 OUT L1 IN EXTERNAL SUPPLY FOR ZONE L1 OUT L1 IN Z+ Z- EXT 24V ZONE MONITORING UNIT (ZMU) J1 &...
- Page 5 CONNECTION SCHEMATIC QUAD-ZMU G L O B A L Analogue Loop F I R E E Q U I P M E N T Connection Board EXTERNAL SUPPLY FOR ZONE FAULT ZONE D LOOP FIRE FAULT ZONE C FIRE QUAD FAULT ZONE B FIRE...
- Page 6 CONNECTION SCHEMATIC Input/Output G L O B A L EXTERNAL SUPPLY FOR RELAY F I R E E Q U I P M E N T VOLTAGE FREE RELAY CONTACTS IO-ISO REV.: C NOTE: IF USED WITH EXTERNAL POWER SUPPLY, (J1 & J2 on the solder side) SHOULD BE OPEN MONITORED ALARM INPUT...
- Page 7 CONNECTION SCHEMATIC Input G L O B A L F I R E E Q U I P M E N T LOOP INPUT LOOP 2 LOOP 2 LOOP 3 LOOP 3 LOOP 1 LOOP 1 RETURN RETURN RETURN Analogue Loop Connection Board ELECTRICAL CHARACTERISTICS MECHANICAL CHARACTERISTICS...
- Page 8 CONNECTION SCHEMATIC Triple Input / Output G L O B A L EXTERNAL SUPPLY F I R E E Q U I P M E N T FOR RELAYS VOLTAGE FREE RELAY CONTACTS C1 NC NO C2 NC NO C3 NC NO 3 I/O UNIT NOTE: REQUIRES EXTERNAL SUPPLY FOR RELAY OUTPUT...
- Page 9 CONNECTION SCHEMATIC LSC-ISO LOOP SOUNDER CONTROL MODULE WITH AMP MONITORED OUTPUT G L O B A L F I R E E Q U I P M E N T OUTPUT TO EXTERNAL CONVENTIONAL POWER SUPPLY SOUNDERS END OF LINE: 10K RES. L1 L1 EXTERNAL POWER SUPPLY...
- Page 10 CONNECTION SCHEMATIC LSCM1 LOOP SOUNDER CONTROL MODULE G L O B A L F I R E E Q U I P M E N T TO SOUNDER SOUNDER BEACON BLACK TECHNICAL CHARACTERISTICS 17-40 VOLTS DC 30 - 95% NON-CONDENSING WORKING VOLTAGE: HUMIDITY: 330uA MAX.
- Page 11 CONNECTION SCHEMATIC MCPA-KAC G L O B A L F I R E E Q U I P M E N T ...TO THE NEXT DEVICE HAUT OBEN NO POLARITY FOR WIRES COMING FROM MODULE COMING FROM THE INSTALLATION (SHADED AREA CONNECTS FROM MODULE ONLY) LOOP 2 LOOP 2 LOOP 3...
- Page 12 CONNECTION SCHEMATIC MCPA-LP G L O B A L F I R E E Q U I P M E N T 1 2 3 4 5 6 7 8 L1 L1 L2 L2 ADDRESS LOOP 2 LOOP 2 LOOP 3 LOOP 3 LOOP 1 LOOP 1...
- Page 13 CONNECTION SCHEMATIC VULCAN-A G L O B A L F I R E E Q U I P M E N T CONNECTIONS AND TONE CONFIGURATIONS FOR VULCAN ADDRESSABLE SOUNDER DETECTOR BASE L1 L1 L2 L2 = JUMPER SWEEPING ALTERNATING ALTERNATING CONTINUOUS TONE...
- Page 14 CONNECTION SCHEMATIC VIPER-SE-A G L O B A L F I R E E Q U I P M E N T CONNECTIONS AND TONE CONFIGURATIONS FOR VIPER - SE (SPECIAL EDITION) ADDRESSABLE SOUNDER DETECTOR BASE L1 L1 L2 L2 = JUMPER SWEEPING ALTERNATING...
- Page 15 CONNECTION SCHEMATIC VIPER-SE-C G L O B A L F I R E E Q U I P M E N T CONNECTIONS AND TONE CONFIGURATIONS FOR VULCAN/VIPER-SE CONVENTIONAL SOUNDER ALTERNATING LOW-FREQUENCY TONE SWEEPING TONE C- C- ALTERNATING HIGH-FREQUENCY TONE = JUMPER NOTE: TO OBTAIN CONTINUOUS TONE CONNECT 0V TO C- TERMINALS (SHORT BETWEEN - AND C-)
-
Page 16: Dip Switch Addressing
G L O B A L F I R E E Q U I P M E N T DIP SWITCH ADDRESSING 101. 102. 103. 104. 105. 106. 107. 108. 109. 110. 111. 112. 113. 114. 115. 116. 117. 118. 119.
Need help?
Do you have a question about the JUNO NET and is the answer not in the manual?
Questions and answers