Table of Contents
Advertisement
en | 2 | Operating Instructions | SMT500 Leak Detector
Safety Precautions
BEFORE OPERATING THIS TOOL, ALL OPERATORS SHOULD
READ AND UNDERSTAND THIS DOCUMENT AND FOLLOW
ALL SAFETY WARNINGS AND INSTRUCTIONS.
KEEP THESE INSTRUCTIONS WITH THE TOOL FOR FUTURE
REFERENCE. IF YOU HAVE ANY QUESTIONS, CONTACT YOUR
BOSCH REPRESENTATIVE OR DISTRIBUTOR.
DANGER
When an engine is operating, keep the service area well
ventilated or attach a building exhaust removal system to the
engine exhaust system. Engines produce carbon monoxide, an
odorless, poisonous gas that causes slower reaction time and
can lead to death or serious personal injury.
WARNING:
•
All diagnostic work should be performed with the engine off
•
Do not leave a vehicle unattended while equipment is
connected or operating
•
Operates on a 12-volt battery: connect to battery (+) and
chassis ground (-)
•
Vapor chamber can become hot. Do not lift or carry by
vapor chamber
•
Do not perform tests near a source of spark of ignition
•
When working with the fuel system, work in a well-venti-
lated area
•
Always wear the appropriate safety protection
•
Wear OSHA standard eyewear and protective gloves
when using this equipment
•
When working with hydraulic or fuel lines, be careful
that liquids under pressure do not escape and create a
dangerous condition. Use adequate ventilation and make
sure there are no sparks or possibility of sparks that may
ignite any vapor.
•
Wear an American National Standards Institute (ANSI) Z87.1
approved eye shield when testing or repairing vehicles.
•
Objects propelled by whirling engine components or
pressurized liquids escaping may cause personal injury.
•
Set the parking brake and block the wheels before test-
ing or repairing a vehicle. It is especially important to
block the wheels on front-wheel drive vehicles because
the parking brake does not hold the drive wheels.
•
Do not drive the vehicle and operate the software at the
same time.
•
Maintain adequate clearance around moving components
or belts during testing.
•
Moving components and belts can catch loose clothing,
body parts, or test equipment and cause serious personal
injury or tool damage.
•
Automotive batteries contain sulfuric acid and produce
explosive gases that can result in serious injury due to
ignition of gases. Keep lit cigarettes, sparks, flames, and
other ignition sources away from the battery at all times.
•
Refer to the service manual for the vehicle being ser-
viced. Adhere to all diagnostic procedures and precau-
tions. Failure to do so could result in personal injury or
otherwise unneeded repairs.
•
Use only specially designed replacement parts (brake
hoses and lines) for ABS equipped vehicles.
•
After bleeding the brake system, check the brake pedal
for excessive travel or a "spongy" feel. Bleed again if
either condition is present.
•
When installing transmitting devices (Citizen Band radio,
telephone, etc) on ABS-equipped vehicles, do not locate
the antenna near the ABS control unit or any other con-
trol unit.
•
This equipment has been tested and found to comply with
SP01501467 | REV A | 4.2021
the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates and
radiates radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harm-
ful interference to radio communications.
•
Do not operate the tool with a damaged cord or connector.
Replace damaged cords and connectors immediately.
•
Do not expose tool to rain, moisture, or snow.
•
Verify that cords are located where they will not be
stepped on, tripped over, or otherwise become a safety
hazard or subjected to damage or stress.
•
Do not store or leave your tool near a heat source such as
a radiator, fireplace, stove, electric heater, or other heat-
generating appliance or otherwise expose it to tempera-
tures in excess of 60ºC (140ºF). When heated to excessive
temperatures, battery cells could explode or vent, causing
personal injury or risk of fire.
CAUTION:
•
Do not place the tool on the distributor of a vehicle.
Strong electromagnetic interference can damage the tool.
•
Never disconnect or reconnect any electrical connec-
tor while the ignition is on. Powertrain Control Module
(PCM) damage may result.
Bosch Automotive Service Solutions Inc
Advertisement
Table of Contents
