On-Screen Display - Harman Kardon AVR 85 Owner's Manual

or . When either input
AUDIO VIDEO
type is highlighted in reverse video use
the or buttons to select the
i
‹ ›
source you wish to listen to or view.
Remember that the video source should
be selected first when you wish to watch
one source and listen to another.
To select a digital audio input use the
or buttons to position the on-
i
⁄ ¤
screen cursor next to
> DIGITAL
and note that the word
Select j
will be highlighted in reverse
DIGITAL
video. Then use the or
‹ ›
to select the desired digital source. Note
that when the digital source is selected,
the audio source will indicate
You may also use this menu to turn the
attenuation, or ATT, function on for this
source only by moving the cursor to the
line and using the or
‹
ATT
to select or . When the ATT
i
ON OFF
function is enabled the input level is
reduced to prevent overloading the input
circuits.
: At this menu (see
SURROUND MODE
figure #15) you may change the
surround mode by using the
buttons to position the on-screen
i
cursor next to and using the
> MODE
or buttons to select the desired
i
‹ ›
mode. To change the delay time position
the cursor next to
SURROUND CH
then use the or buttons
‹ ›
desired delay time for the surround
channels. Note that an adjustment for
the delay time of the center channel is
possible only in the Dolby Digital mode.
: At this menu you may
TEST TONE
adjust the speaker output levels. For
information on this procedure, refer to
the System Configuration section of this
manual.

On-Screen Display

MULTI-ROOM SEL
on configuring and using the multiroom
audio functions of the AVR85, consult the
appropriate section of this manual.
SET UP MENU
using the Setup menus, refer to the
System Configuration section of this
manual.
. Press
SLEEP TIMER SET
to set the sleep timer, which you will
place the unit in a standby mode after a
buttons
i
set period of time. To reach this menu,
press the
position the on-screen cursor
.
** SLEEP TIMER
At the next screen, the
menu (see figure #16) the cursor
SET
will be next to
or buttons
›
buttons
time before turn off and note that the
›
time will blink. Press the
that the on-screen cursor
is next to
or buttons
‹ ›
press
Select j
stop flashing indicating that the timer
has been started. Press
or
so that the cursor is next to
⁄ ¤
TO MAIN MENU
that when the
the screen the time figure will appear
next to the words
and
may check the time remaining before
to select
i
shut off at any time by pressing the
button
Sleep
viewing the on-screen display (see figure
#12).
Position the on-screen cursor
to
MENU OFF
menu system and return to normal
operation.
27
: For information
: For information on
: This enables you
or buttons to
i
⁄ ¤
next to
>
and press
Select j
SLEEP TIMER
. Use the
TIMER SET
to select the amount of
i
button so
¤
>
. Use the
TIMER ON OFF
to highlight
i
ON
. The time figure will
one more time
¤
RETURN
and press select. Note
returns to
MAIN MENU
. You
SLEEP TIMER
on the remote and
z
next
>
at any time to exit the
S U R R O U N D
M O D E : P R O
D E L A Y T I M E
C E N T E R C H
S U R R O U N D
R E T U R N T O
Figure 15
S L E E P T I M E R
T I M E R S E T
T I M E R O F F
.
R E T U R N T O
Figure 16
‹
and
M O D E
L O G I C
C O N T R O L
: N O N E
C H : 2 m s
M A I N M E N U
S E T
1 0 m i n
O N
M A I N M E N U