Digital Audio Sources; Tuner Operation - Harman Kardon AVR 85 Owner's Manual

Note: Once a program has been encoded
with surround information, it retains the
surround matrix as long as the program
is broadcast in stereo. Thus, movies with
surround sound will carry surround
information when they are broadcast via
conventional TV stations, cable, pay TV
and satellite transmission. In addition, a
growing number of made-for-television
programs, sports broadcasts, radio dra-
mas and music CDs are also recorded in
surround sound. You may obtain a list of
these programs and discs from the Dolby
Laboratories web site at www.dolby.com
Surround modes may be selected in one
of three ways.
From the front panel, use the
or buttons to scroll
@
Mode ¤
through the list of modes. The selected
mode will appear in large letters in the
front panel display, and in a two-line
reminder on the video screen. Once the
selection is made, the mode will continue
to appear in a smaller indictor at the
bottom of the front panel display
(see figure 9).
From the remote, modes may be selected
by simply pressing the button that corre-
sponds to the desired mode
Modes may also be selected using the on-
screen display. Press
Select j
remote to display the
MAIN MENU
Then press twice so that the on-
i
¤
screen cursor is next to
SURROUND
. Press again to move
Select j
MODE
to the next menu.
At the Surround Mode Menu, press the
‹ ›
or buttons until the desired
i
mode name appears on the screen. Press
until the on-screen cursor
¤
to
RETURN TO MAIN MENU
press . At the main menu select
Select
Basic Operation
MENU OFF
menus.
A different mode may be selected for
audio and video sources. Once a mode
has been selected, it will be attached to
those sources in memory. Thus, you
may select
one video source and
After the initial selections are made, the
unit will automatically return to your
preferred mode for each type of input
whenever it is chosen.

Digital Audio Sources

When a source is connected to the AVR85
and playing digital audio information,
first select the source using the front
panel or remote input selectors, and then
⁄
Mode
press the appropriate digital input using
the
Digital Input Selectors g9
the remote or front panel. Depending on
the type of digital source in use, the
indicator
AC-3
Dolby Digital signal is present, or the
indicator
PCM
standard two-channel SP/DIF-type
digital signal is present.
Once a Dolby Digital signal is detected
the unit will automatically switch to the
. Dolby Digital mode. When a PCM digital
y
source is detected you may select any of
the surround modes except Dolby Digital.
on the
. Note: The Dolby Digital mode may not
be selected when PCM digital or analog
signals are present. If the Dolby Digital
mode is selected when an AC-3 input is
not detected the AVR85 will default to the
STEREO
is next
>
and
22
and press to exit the
Select
as the mode for
PRO LOGIC
for another.
HALL
will light when a
A
will light when a
R
mode.
For information on using Digital Audio
Sources, see the Advanced Features
section of this manual.
IMPORTANT NOTE: Many people
incorrectly presume that sound should
always be heard from the surround
channels. In reality, it is normal for
the surround channels to operate occa-
sionally, and often to be silent. Movie
directors and sound mixers typically
use these channels only when needed to
create an effect or establish ambience.
Artificially increasing the volume level
to the surround channels may destroy
the illusion of carefully controlled audio
effects and add unwanted noise to your
system.

Tuner Operation

on The FM/AM tuner is extremely flexible,
and offers a number of options. The
following instructions will enable you
to take advantage of the tuner's many
features.
To select tuner operation, press the
button
2
AM/FM
or the remote . Press the button again
d
to select the desired frequency band if
required.
Manual up/down tuning is accessible
by pressing the
Tune
either up or down
⁄
‚ TUNE /SEARCH —
buttons on the remote. Pressing
s
these buttons once increases or decreases
the station frequency by one step.
Holding the buttons down quickly scans
for the next station. Holding the tune
buttons for a few seconds and then
releasing them will set the tuner to the
next station with an acceptable signal.
on the front panel,
button
Ú
or the
¤